IEC 61784-5-17-2013 Industrial communication networks - Profiles - Part 5-17 Installation of fieldbuses - Installation profiles for CPF 17《工业通信网络.配置文件.第5-17部分 现场总线的安装.CPF 17安装配置文件》.pdf

《IEC 61784-5-17-2013 Industrial communication networks - Profiles - Part 5-17 Installation of fieldbuses - Installation profiles for CPF 17《工业通信网络.配置文件.第5-17部分 现场总线的安装.CPF 17安装配置文件》.pdf》由会员分享，可在线阅读，更多相关《IEC 61784-5-17-2013 Industrial communication networks - Profiles - Part 5-17 Installation of fieldbuses - Installation profiles for CPF 17《工业通信网络.配置文件.第5-17部分 现场总线的安装.CPF 17安装配置文件》.pdf（56页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61784-5-17 Edition 1.0 2013-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial communication networks Profiles Part 5-17: Installation of fieldbuses Installation profiles for CPF 17 Rseaux de communication industriels Profils Partie 5-17: Installation des bus de terrain Profils dinstalla

2、tion pour CPF 17 IEC 61784-5-17:2013 colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, includi

3、ng photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or

4、your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les

5、microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de vo

6、tre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International St

7、andards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC pub

8、lications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Sta

9、y up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definiti

10、ons in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the C

11、ustomer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications C

12、EI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des p

13、ublications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Publish

14、ed dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi

15、que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 6

16、1784-5-17 Edition 1.0 2013-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial communication networks Profiles Part 5-17: Installation of fieldbuses Installation profiles for CPF 17 Rseaux de communication industriels Profils Partie 5-17: Installation des bus de terrain Profils dinstallation p

17、our CPF 17 INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE U ICS 25.040.40; 35.100.40 PRICE CODE CODE PRIX ISBN 978-2-8322-1069-7 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale W

18、arning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colour inside 2 61784-5-17 IEC:2013 CONTENTS FOREWORD . 5 INTRODUCTION . 7 1 Scope . 8 2 Normative references . 8 3 Te

19、rms, definitions and abbreviated terms . 8 4 CPF 17: Overview of installation profiles 8 5 Installation profile conventions . 8 6 Conformance to installation profiles 9 Annex A (Normative) CP 17/1 (RAPIEnet) specific installation profile. 10 A.1 Installation profile scope . 10 A.2 Normative referenc

20、es . 10 A.3 Installation profile terms, definitions, and abbreviated terms . 10 A.3.1 Terms and definitions 10 A.3.2 Abbreviated terms . 10 A.3.3 Conventions for installation profiles . 10 A.4 Installation planning . 10 A.4.1 General . 10 A.4.1.1 Objective 10 A.4.1.2 Cabling in industrial premises .

21、 10 A.4.1.3 The planning process 10 A.4.1.4 Specific requirements for CPs . 10 A.4.1.5 Specific requirements for generic cabling in accordance with ISO/IEC 24702 10 A.4.2 Planning requirements . 10 A.4.2.1 Safety . 10 A.4.2.2 Security 10 A.4.2.3 Environmental considerations and EMC 10 A.4.2.4 Specif

22、ic requirements for generic cabling in accordance with ISO/IEC 24702 11 A.4.3 Network capabilities 11 A.4.3.1 Network topology 11 A.4.3.2 Network characteristics . 11 A.4.4 Selection and use of cabling components 12 A.4.4.1 Cable selection . 12 A.4.4.2 Connecting hardware selection . 14 A.4.4.3 Conn

23、ections within a channel/permanent link 15 A.4.4.4 Terminators 16 A.4.4.5 Device location and connection . 16 A.4.4.6 Coding and labelling . 16 A.4.4.7 Earthing and bonding of equipment and devices and shielded cabling 16 A.4.4.8 Storage and transportation of cables . 17 A.4.4.9 Routing of cables 18

24、 A.4.4.10 Separation of circuit 18 A.4.4.11 Mechanical protection of cabling components . 18 61784-5-17 IEC:2013 3 A.4.4.12 Installation in special areas . 18 A.4.5 Cabling planning documentation 19 A.4.5.1 Common description . 19 A.4.5.2 Cabling planning documentation for CPs . 19 A.4.5.3 Network c

25、ertification documentation 19 A.4.5.4 Cabling planning documentation for generic cabling in accordance with ISO/IEC 24702. 19 A.4.6 Verification of cabling planning specification . 19 A.5 Installation implementation . 19 A.5.1 General requirements 19 A.5.1.1 Common description . 19 A.5.1.2 Installat

26、ion of CPs . 19 A.5.1.3 Installation of generic cabling in industrial premises 19 A.5.2 Cable installation . 19 A.5.2.1 General requirements for all cabling types 19 A.5.2.2 Installation and routing 20 A.5.2.3 Specific requirements for CPs . 20 A.5.2.4 Specific requirements for wireless installation

27、 . 20 A.5.2.5 Specific requirements for generic cabling in accordance with ISO/IEC 24702 21 A.5.3 Connector installation 21 A.5.3.1 Common description . 21 A.5.3.2 Shielded connectors . 21 A.5.3.3 Unshielded connectors 21 A.5.3.4 Specific requirements for CPs . 21 A.5.3.5 Specific requirements for g

28、eneric cabling in accordance with ISO/IEC 24702 21 A.5.4 Terminator installation . 21 A.5.5 Device installation . 21 A.5.5.1 Common description . 21 A.5.5.2 Specific requirements for CPs . 21 A.5.6 Coding and labelling 21 A.5.6.1 Common description . 21 A.5.6.2 Specific requirements for CPs . 21 A.5

29、.7 Earthing and bonding of equipment and devices and shield cabling . 21 A.5.7.1 Common description . 21 A.5.7.2 Bonding and earthing of enclosures and pathways 21 A.5.7.3 Earthing methods 21 A.5.7.4 Shield termination methods . 22 A.5.7.5 Specific requirements for CPs . 22 A.5.7.6 Specific requirem

30、ents for generic cabling in accordance with ISO/IEC 24702 22 A.5.8 As-implemented cabling documentation . 22 A.6 Installation verification and installation acceptance test 22 A.6.1 General . 22 A.6.2 Installation verification . 22 A.6.2.1 General . 22 A.6.2.2 Verification according to cabling planni

31、ng documentation 22 A.6.2.3 Verification of earthing and bonding 22 A.6.2.4 Verification of shield earthing 22 4 61784-5-17 IEC:2013 A.6.2.5 Verification of cabling system 22 A.6.2.6 Cable selection verification . 23 A.6.2.7 Connector verification . 23 A.6.2.8 Connection verification 23 A.6.2.9 Term

32、inators verification . 23 A.6.2.10 Coding and labelling verification . 23 A.6.2.11 Verification report . 23 A.6.3 Installation acceptance test . 23 A.6.3.1 General . 23 A.6.3.2 Acceptance test of Ethernet based cabling 23 A.6.3.3 Acceptance test of non-Ethernet-based cabling . 24 A.6.3.4 Specific re

33、quirements for wireless installation . 24 A.6.3.5 Acceptance test report 24 A.7 Installation administration . 24 A.8 Installation maintenance and installation troubleshooting . 24 Figure 1 Standards relationships 7 Table A.1 Network characteristics for balanced cabling based on Ethernet 11 Table A.2

34、 Network characteristics for optical fibre cabling 12 Table A.3 Information relevant to copper cable: fixed cables 13 Table A.4 Information relevant to copper cable: cords 13 Table A.5 Information relevant to optical fibre cables . 14 Table A.6 Connectors for balanced cabling CPs based on Ethernet .

35、 14 Table A.7 Optical fibre connecting hardware 15 Table A.8 Relationship between FOC and fibre types (CP 17/1) . 15 Table A.9 Parameters for balanced cables . 19 Table A.10 Parameters for silica optical fibre cables 20 61784-5-17 IEC:2013 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ INDUSTRIAL COM

36、MUNICATION NETWORKS PROFILES Part 5-17: Installation of fieldbuses Installation profiles for CPF 17 FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The objec

37、t of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specification

38、s (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaisi

39、ng with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express,

40、 as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees

41、 in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Co

42、mmittees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not pr

43、ovide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the l

44、atest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, w

45、hether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

46、 indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC

47、61784-5-17 has been prepared by subcommittee 65C: Industrial networks, of IEC technical committee 65: Industrial-process measurement, control and automation. This standard is to be used in conjunction with IEC 61918:2013. 6 61784-5-17 IEC:2013 The text of this standard is based on the following docu

48、ments: FDIS Report on voting 65C/738/FDIS 65C/743/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of IEC 61

49、784-5 series, under the general title Industrial communication networks Profiles Installation of fieldbuses, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed