IEC 61169-59-2017 Radio-frequency connectors - Part 59 Sectional specification for type L32-4 and L32-5 threaded multi-pin radio-frequency connectors《射频连接器 第59部分 L32-4和L32-5型螺纹式多芯射频连接器分规格》.pdf

《IEC 61169-59-2017 Radio-frequency connectors - Part 59 Sectional specification for type L32-4 and L32-5 threaded multi-pin radio-frequency connectors《射频连接器 第59部分 L32-4和L32-5型螺纹式多芯射频连接器分规格》.pdf》由会员分享，可在线阅读，更多相关《IEC 61169-59-2017 Radio-frequency connectors - Part 59 Sectional specification for type L32-4 and L32-5 threaded multi-pin radio-frequency connectors《射频连接器 第59部分 L32-4和L32-5型螺纹式多芯射频连接器分规格》.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61169-59 Edition 1.0 2017-05 INTERNATIONAL STANDARD Radio-frequency connectors Part 59: Sectional specification for type L32-4 and L32-5 threaded multi-pin radio-frequency connectors IEC 61169-59:2017-05(en) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2017 IEC, Geneva, Switz

2、erland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the countr

3、y of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb

4、 Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publi

5、cations The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibli

6、ographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (re

7、ference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also onc

8、e a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing 20 000 terms and definitions in English and French, with equivalent terms in 16 additional languages. Also known as the International Electrotechnical Vocabulary

9、 (IEV) online. IEC Glossary - std.iec.ch/glossary 65 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Cu

10、stomer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC 61169-59 Edition 1.0 2017-05 INTERNATIONAL STANDARD Radio-frequency connectors Part 59: Sectional specification

11、for type L32-4 and L32-5 threaded multi-pin radio-frequency connectors INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 33.120.30 ISBN 978-2-8322-4398-5 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distrib

12、utor. colour inside 2 IEC 61169-59:2017 IEC 2017 CONTENTS FOREWORD . 4 1 Scope 6 2 Normative references 6 3 Terms and definitions 6 4 Mating face and gauge information 7 4.1 Dimensions General connectors Grade 2 7 4.1.1 Connector with pin contact . 7 4.1.2 Connector with socket contact . 9 4.1.3 Mat

13、ing face of RF channel . 12 4.2 Gauges . 13 4.2.1 Gauge for socket centre contact . 13 4.2.2 Gauge for type L32-5 connector with 5 pin contacts . 14 4.2.3 Gauge for L32-4 connector with 4 pin contacts 15 4.2.4 Gauge for L32-5 connector with 5 socket contacts . 16 4.2.5 Gauge for L32-4 connector with

14、 4 socket contacts . 17 5 Quality assessment procedure . 19 5.1 General . 19 5.2 Rating and characteristics . 19 5.3 Test schedule and inspection requirements. 21 5.3.1 Acceptance tests . 21 5.3.2 Periodic tests . 22 5.4 Procedures for the qualification approval 24 5.4.1 Quality conformance inspecti

15、on . 24 5.4.2 Qualification approval and its maintenance 24 5.4.3 Periodic tests . 24 5.4.4 Procedures for quality conformance . 24 6 Instructions for preparation of detail specifications 25 6.1 General . 25 6.2 Identification of the component . 25 6.3 Performance . 25 6.4 Marking, ordering informat

16、ion and related matters 25 6.5 Selection of tests, test conditions and severities . 25 6.6 Blank detail specification pro-forma for Type L32-4 and L32-5 threaded multi-pin radio frequency connectors . 26 7 Marking . 31 7.1 Marking of component . 31 7.2 Marking and contents of package 31 Annex A (nor

17、mative) Isolation test method . 32 A.1 Preparation of test sample 32 A.2 Test procedure 32 Figure 1 L32-5 connector with 5 pin contacts . 7 Figure 2 L32-4 connector with 4 pin contacts . 8 Figure 3 L32-5 connector with 5 socket contacts 9 Figure 4 L32-4 connector with 4 socket contacts 11 Figure 5 M

18、ating face of RF channel . 12 IEC 61169-59:2017 IEC 2017 3 Figure 6 Gauge for socket contact of RF channel . 13 Figure 7 Gauge for L32-5 connector with 5 pin contacts . 14 Figure 8 Gauge for L32-4 connector with 4 pin contacts . 15 Figure 9 Gauge for L32-5 connector with 5 socket contacts . 16 Figur

19、e 10 Gauge for L32-4 connector with 4 socket contacts . 18 Table 1 Dimensions of L32-5 connector with 5 pin contacts . 8 Table 2 Dimensions of L32-4 connector with 4 pin contacts . 9 Table 3 Dimensions of L32-5 connector with 5 socket contacts 10 Table 4 Dimensions of L32-4 connector with 4 socket c

20、ontacts 11 Table 5 Dimensions of the mating face of RF channel 13 Table 6 Dimensions of gauge for socket contact 14 Table 7 Dimensions of gauge L32-5 connector with 5 pin contacts . 15 Table 8 Dimensions of gauge L32-4 connector with 4 pin contacts . 16 Table 9 Dimensions of gauge for L32-5 connecto

21、r with 5 socket contacts . 17 Table 10 Dimensions of gauge for L32-4 connector with 4 socket contacts . 18 Table 11 Rating and characteristics . 20 Table 12 Acceptance tests . 22 Table 13 Periodic tests 23 4 IEC 61169-59:2017 IEC 2017 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RADIO-FREQUENCY CONNE

22、CTORS Part 59: Sectional specification for type L32-4 and L32-5 threaded multi-pin radio-frequency connectors FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees).

23、 The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Spe

24、cifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizati

25、ons liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matter

26、s express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

27、Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC N

28、ational Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself d

29、oes not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they

30、have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature wha

31、tsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publi

32、cations is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Sta

33、ndard IEC 61169-59 has been prepared by subcommittee 46F: RF and microwave passive components, of IEC technical committee 46: Cables, wires, waveguides, RF connectors, RF and microwave passive components and accessories. The text of this International Standard is based on the following documents: CD

34、V Report on voting 46F/351/CDV 46F/362/RVC Full information on the voting for the approval of this International Standard can be found in the report on voting indicated in the above table. IEC 61169-59:2017 IEC 2017 5 This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

35、A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors, can be found on the IEC website. The committee has decided that the contents of this document will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in

36、 the data related to the specific document. At this date, the document will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cover page of this publication indicates th

37、at it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. 6 IEC 61169-59:2017 IEC 2017 RADIO-FREQUENCY CONNECTORS Part 59: Sectional specification for type L32-4 and L32-5 threaded multi-

38、pin radio-frequency connectors 1 Scope This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for type L32-4 and L32-5 threaded multi-pin radio frequency connectors with anti mismating mechanism, 50 nominal im

39、pedance. The operating frequency of each channel is up to 4 GHz. These connectors have been widely used in mobile communication system like TD-SCDMA and TD-LTE, and can also be used in some similar equipment. It also prescribes mating face dimensions for general connectors-grade 2, gauging informati

40、on and tests selected from IEC 61169-1, applicable to all detail specifications relating to type L32-4 and L32-5 multi-pin connectors. This sectional specification provides information and rules for the preparation of detail specifications for type L32-4 and L32-5 multi-pin connectors together with

41、the pro forma blank detail specification. This specification indicates the recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H. NOTE Metric dimension are original dimension

42、s. All undimensioned pictorial configurations are for reference purpose only. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. Fo

43、r undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61169-1:2013, Radio frequency connectors Part 1: Generic specification General requirements and measuring methods IEC 61726, Cable assemblies, cables, connectors and passive microwave componen

44、ts Screening attenuation measurement by the reverberation chamber method IEC 62037 (all parts), Passive RF and microwave devices, intermodulation level measurement 3 Terms and definitions No terms and definitions are listed in this document. ISO and IEC maintain terminological databases for use in s

45、tandardization at the following addresses: IEC 61169-59:2017 IEC 2017 7 IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp 4 Mating face and gauge information 4.1 Dimensions General connectors Grade 2 4.1.1 Connector with pin c

46、ontact 4.1.1.1 L32-5 connector with 5 pin contacts The mating face of L32-5 connector with 5 pin contacts is shown in Figure 1 and its dimensions are shown in Table 1. NOTE 1 Mechanical and electrical reference plane. NOTE 2 Chamfer of three grooves is optional. NOTE 3 The mating face of RF channel

47、with pin contact is shown in Figure 5a) in 4.1.3 and its dimensions are shown in Table 5. NOTE 4 The shape of seal ring is optional. NOTE 5 Anti-mismating pin. NOTE 6 The initial position number of RF channel with pin contact and the other positions numbered clockwise. Figure 1 L32-5 connector with

48、5 pin contacts IEC Note1 C Note4 Note2 Note3 0.1 A B C 1 36 108 144 216 Note5 180 B Main groove Note6 A 0 5Pin EQS2Supplementary groove 8 IEC 61169-59:2017 IEC 2017 Table 1 Dimensions of L32-5 connector with 5 pin contacts Ref. mm Min. Max. a 6,0 6,1 b 6,0 6,2 c 7,5 7,6 d M32X1,5-6g e 14,4 14,5 f 6,

49、0 g 9,5 9,7 h 24,0 k 27,0 27,1 m 2,1 2,2 n 16,5 4.1.1.2 L32-4 connector with 4 pin contacts The mating face of L32-4 connector with 4 pin contacts is shown in Figure 2 and its dimensions are shown in Table 2. NOTE 1 Mechanical and electrical reference plane. NOTE 2 Chamfer of three grooves is optional. NOTE 3 The mating face of RF channel with pin contact is shown in Figure 5a) in 4.1.3 and its dimensions are shown in Table 5.