IEC 61169-26-2013 Radio frequency connectors - Part 26 Sectional specification for TNCA series RF coaxial connectors《射频连接器.第26部分 TNCA系列射频同轴电缆连接器分规范》.pdf

《IEC 61169-26-2013 Radio frequency connectors - Part 26 Sectional specification for TNCA series RF coaxial connectors《射频连接器.第26部分 TNCA系列射频同轴电缆连接器分规范》.pdf》由会员分享，可在线阅读，更多相关《IEC 61169-26-2013 Radio frequency connectors - Part 26 Sectional specification for TNCA series RF coaxial connectors《射频连接器.第26部分 TNCA系列射频同轴电缆连接器分规范》.pdf（56页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61169-26 Edition 1.0 2013-01 INTERNATIONAL STANDARD NORME INTERNATIONALE Radio-frequency connectors Part 26: Sectional specification for TNCA series RF coaxial connectors Connecteurs pour frquences radiolectriques Partie 26: Spcification intermdiaire pour les connecteurs coaxiaux RF srie TNCA I

2、EC61169-26:2013 colourinsideTHIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and mic

3、rofilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member N

4、ational Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccor

5、d crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. I

6、EC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electri

7、cal, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.

8、iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new

9、 IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and Fren

10、ch, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre:

11、 csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique

12、 des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en util

13、isant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelle

14、s publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalen

15、ts dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61169-26 Edition 1.0 201

16、3-01 INTERNATIONAL STANDARD NORME INTERNATIONALE Radio-frequency connectors Part 26: Sectional specification for TNCA series RF coaxial connectors Connecteurs pour frquences radiolectriques Partie 26: Spcification intermdiaire pour les connecteurs coaxiaux RF srie TNCA INTERNATIONAL ELECTROTECHNICAL

17、 COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE U ICS 31.220.10 PRICE CODE CODE PRIX ISBN 978-2-83220-624-9 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication

18、 from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colourinside 2 61169-26 IEC:2013 CONTENTS FOREWORD . 4 1 Scope . 6 2 Normative reference . 6 3 Mating face and gauge information . 6 Dimensions General connectors Grade 1

19、 . 6 3.1Connector with pin-centre contact (see Figure 1) . 6 3.1.1Connector with socket-centre contact (see Figure 2) . 8 3.1.2Gauges . 9 3.2Gauge pins for socket-centre contact (see Figure 3) 9 3.2.1Test procedure 9 3.2.2Dimensions Standard test connectors Grade 0 10 3.3Connector with pin-centre co

20、ntact (see Figure 4) . 10 3.3.1Connector with socket-centre contact (see Figure 5) . 11 3.3.24 Quality assessment procedure 12 General . 12 4.1Rating and characteristics (see Clause 6 of IEC 61169-1:1992) 12 4.2Test schedule and inspection requirements Acceptance tests . 15 4.3Acceptance tests (see

21、Table 8) 15 4.3.1Periodic tests. 16 4.3.2Procedures 18 4.4Quality conformance inspection . 18 4.4.1Qualification approval and its maintenance 18 4.4.25 Instructions for preparation of detail specifications . 19 General . 19 5.1Identification of the component 19 5.2Performance 19 5.3Marking, ordering

22、 information and related matters . 19 5.4Selection of tests, test conditions and severities 19 5.5Blank detail specification pro-forma for type TNCA connector 21 5.6Bibliography 26 Figure 1 Connector with pin-centre contact (for dimensions and key, see Table 1) 7 Figure 2 Connector with socket-centr

23、e contact (for dimensions and key, see Table 2) 8 Figure 3 Gauge pins for socket-centre contact (for dimensions, see Table 3) 9 Figure 4 Connector with pin-centre contact (for dimensions and key, see Table 4) 10 Figure 5 Connector with socket-centre contact (for dimensions and key, see Table 5) 11 T

24、able 1 Dimensions of connector with pin-centre contact . 7 Table 2 Dimensions of connector with socket-centre contact 8 Table 3 Dimensions of gauge pins for socket-centre contact 9 Table 4 Dimensions of connector with pin-centre contact . 10 Table 5 Dimensions of connector with socket-centre contact

25、 11 Table 6 Preferred climatic categories (see IEC 60068-1) 12 Table 7 Ratings and characteristics . 13 61169-26 IEC:2013 3 Table 8 Acceptance tests . 15 Table 9 Periodic tests 16 4 61169-26 IEC:2013 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RADIO-FREQUENCY CONNECTORS Part 26: Sectional specificat

26、ion for TNCA series RF coaxial connectors FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all q

27、uestions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publicat

28、ion(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC c

29、ollaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opini

30、on on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to en

31、sure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently

32、to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certificat

33、ion bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall at

34、tach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fe

35、es) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publicat

36、ion. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61169-26 has been prepared by subcommittee 46F: RF and micr

37、owave passive components, of IEC technical committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories. The text of this standard is based on the following documents: FDIS Report on voting 46F/220/FDIS 46F/225/RVD Full information on the voting for

38、 the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 61169-26 IEC:2013 5 A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors,

39、 can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfir

40、med, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a col

41、our printer. 6 61169-26 IEC:2013 RADIO-FREQUENCY CONNECTORS Part 26: Sectional specification for TNCA series RF coaxial connectors 1 Scope This part of IEC 61169 which is a sectional specification (SS) provides information and rules for the preparation of detail specifications (DS) for TNCA series R

42、F coaxial connectors, with characteristic impedance of 50 , with threaded coupling and operating frequency limit up to 18 GHz, used in wireless, communication, instrument, antenna, test and measurements, radar, and other fields, connecting with RF cables or micro-strips. It also prescribes mating fa

43、ce dimensions for general connectors-grade 2, dimensional details of standard test connectors-grade 0, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to TNCA series connectors. This specification indicates the recommended performance charact

44、eristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H (see Tables 8 and 9). TNCA connectors are recommended for applications above 11 GHz. TNCA connectors are compatible with TNC connectors as described in

45、 the IEC 60169-17 and IEC 60169-26 provided that the dielectric of connector with socket-centre contact does not extend beyond reference plane. However when mated with these connectors, the performances are not ensured. NOTE Attention is drawn to the fact that TNCA interface does not utilize overlap

46、ping PTFE dielectric for increased voltage breakdown resistance. 2 Normative reference The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, th

47、e latest edition of the referenced document (including any amendments) applies. IEC 61169-1:1992, Radio-frequency connectors Part 1: Generic specification General requirements and measuring methods1Amendment 1:1996 Amendment 2:1997 IEC 60068-1, Environmental testing Part 1: General and guidance 3 Ma

48、ting face and gauge information Dimensions General connectors Grade 1 3.1Connector with pin-centre contact (see Figure 1) 3.1.1Metric dimensions are original dimensions. _ 1There exists a consolidated edition 1.2 (1998) that comprises IEC 61169-1:1992, its Amendment 1:1996 and its Amendment 2:1997.

49、61169-26 IEC:2013 7 All undimensioned pictorial configurations are for reference purpose only. Note 2 Reference plane Detail for pin contact abcsrd(2) p h n Full theard g e f Reference plane Sealing gasket to meet required functional and environmental performance ad k 55 66 1 4 7/16-28UNEF-2B(1) m IEC 269/13 Figure 1 Connector with pin-centre contact (for dimensions