IEC 60793-1-50-2014 Optical fibres - Part 1-50 Measurement methods and test procedures - Damp heat (steady state) tests《光纤 第1-50部分：测量方法和试验规程 湿热（稳态）试验》.pdf

《IEC 60793-1-50-2014 Optical fibres - Part 1-50 Measurement methods and test procedures - Damp heat (steady state) tests《光纤 第1-50部分：测量方法和试验规程 湿热（稳态）试验》.pdf》由会员分享，可在线阅读，更多相关《IEC 60793-1-50-2014 Optical fibres - Part 1-50 Measurement methods and test procedures - Damp heat (steady state) tests《光纤 第1-50部分：测量方法和试验规程 湿热（稳态）试验》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60793-1-50 Edition 2.0 2014-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Optical fibres Part 1-50: Measurement methods and test procedures Damp heat (steady state) tests Fibres optiques Partie 1-50: Mthodes de mesure et procdures dessai Essais de chaleur humide (tat continu) IEC 60793-1-50:20

2、14-09(en-fr) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2014 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and micr

3、ofilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member Na

4、tional Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord

5、 crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Centra

6、l Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, elec

7、tronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-a

8、lone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to fi

9、nd IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publ

10、ications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 14 additional languages. A

11、lso known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collec

12、ted from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique

13、Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publications IEC est constamment revu. Veuillez vous assu

14、rer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Spcifications techniques, Rapports techniques et autres

15、 documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur le

16、s projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia

17、.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 14 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire I

18、EC - std.iec.ch/glossary Plus de 55 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clie

19、nts - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 60793-1-50 Edition 2.0 2014-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Optical fibres Part 1-50: Measurement methods and test procedures Damp h

20、eat (steady state) tests Fibres optiques Partie 1-50: Mthodes de mesure et procdures dessai Essais de chaleur humide (tat continu) INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE H ICS 33.180.10 PRICE CODE CODE PRIX ISBN 978-2-8322-1853-2 Registered trademark of

21、the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colour in

22、side 2 IEC 60793-1-50:2014 IEC 2014 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Apparatus 6 3.1 Chamber . 6 3.2 Humidifier . 6 3.3 Other apparatus 6 4 Sampling and specimens . 6 5 Procedure 6 5.1 General . 6 5.2 Optical measurements 6 5.3 Mechanical measurements 7 5.4 Preconditioning

23、. 7 5.5 Conditioning 7 5.6 Recovery 7 6 Pass/fail criteria . 7 7 Results 7 7.1 Information to be provided with each test 7 7.2 Information to be available upon request . 8 8 Specification information . 8 IEC 60793-1-50:2014 IEC 2014 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ OPTICAL FIBRES Part 1

24、-50: Measurement methods and test procedures Damp heat (steady state) tests FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote i

25、nternational co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (here

26、after referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also par

27、ticipate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible,

28、an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While al

29、l reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to ap

30、ply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of

31、 conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this pu

32、blication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirec

33、t, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the c

34、orrect application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60793-1-50 has been prep

35、ared by subcommittee 86A: Fibres and cables, of IEC technical committee 86: Fibre optics. This second edition cancels and replaces the first edition, published in 2001, and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previou

36、s edition: harmonization of the content with sectional specifications of relevant fibre types; extension of the applicability of the standard to class C single-mode fibres. 4 IEC 60793-1-50:2014 IEC 2014 The text of this standard is based on the following documents: CDV Report on voting 86A/1526/CDV

37、 86A/1572/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 60793 series, published under the gene

38、ral title Optical fibres, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the pub

39、lication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print

40、this document using a colour printer. IEC 60793-1-50:2014 IEC 2014 5 OPTICAL FIBRES Part 1-50: Measurement methods and test procedures Damp heat (steady state) tests 1 Scope This part of IEC 60793 provides a practical method for evaluating fibre performance in a defined environment. The purpose of t

41、his standard is to determine the suitability of optical fibre sub-category A1a to A1d multimode fibres and class B and C single-mode fibres to withstand the environmental condition of high humidity and high temperature which may occur in actual use, storage and/or transport. The test is primarily in

42、tended to permit the observation of effects of high humidity at constant temperature over a given period. This procedure is conducted in accordance with IEC 60068-2-78, Test Cab. NOTE The applicability of this test to other fibre categories is under study. 2 Normative references The following docume

43、nts, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068-2-78, Environment

44、al testing Part 2-78: Tests Test Cab: Damp heat, steady state IEC 60793-1-31, Optical fibres Part 1-31: Measurement methods and test procedures Tensile strength IEC 60793-1-32, Optical fibres Part 1-32: Measurement and test procedures Coating strippability IEC 60793-1-33, Optical fibres Part 1-33: M

45、easurement methods and test procedures Stress corrosion susceptibility IEC 60793-1-40:2001, Optical fibres Part 1-40: Attenuation measurement methods IEC 60793-2-10, Optical fibres Part 2-10: Product specifications Sectional specification for category A1 multimode fibres IEC 60793-2-50, Optical fibr

46、es Part 2-50: Product specifications Sectional specification for class B single mode fibres IEC 60793-2-60, Optical fibres Part 2-60: Product specifications Sectional specification for class C single-mode intraconnection fibres 6 IEC 60793-1-50:2014 IEC 2014 3 Apparatus 3.1 Chamber The apparatus con

47、sists of an environmental chamber in accordance with IEC 60068-2-78, Test Cab. The chamber shall be capable of housing the specimen and of allowing access for measurement during conditioning. It shall also be capable of maintaining the specified temperature and humidity within the specified toleranc

48、es. Forced air circulation may be used to maintain homogeneous conditions. The chamber and accessories shall be constructed and arranged in such a manner as to avoid condensation dripping on the specimen. 3.2 Humidifier De-mineralized or de-ionized water is used to obtain the specified humidity. No

49、rust or corrosion contaminants shall be imposed on the specimen by the test facility. The water added to the humidifier shall be controlled according to the manufacturers instructions. 3.3 Other apparatus Additional apparatus may be necessary to perform the examinations and measurements (or as specified in the detail specification). 4 Sampling and specimens For optical measurements, the