UL 496 CRD-2013 UL Standard for Safety Lampholders - Section Paragraph Reference 4 8 6 3 Subject Minimum lead wire gauge size for GU24 outlet-box lampholders (Edition 13 September.pdf

《UL 496 CRD-2013 UL Standard for Safety Lampholders - Section Paragraph Reference 4 8 6 3 Subject Minimum lead wire gauge size for GU24 outlet-box lampholders (Edition 13 September.pdf》由会员分享，可在线阅读，更多相关《UL 496 CRD-2013 UL Standard for Safety Lampholders - Section Paragraph Reference 4 8 6 3 Subject Minimum lead wire gauge size for GU24 outlet-box lampholders (Edition 13 September.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUNDERWRITERS LABORATORIES INC. CERTIFICATION REQUIREMENT DECISIONThis Certification Requirement Decision is prepared and published by Underwriters Laboratories Inc.(UL). It is normative for the a

2、pplicable UL Product Certification Program(s); however, it is currently notpart of the UL Standard(s) referenced below.Product Category (CCN): OKCT, OKCT7Standard Number: UL 496Edition Date: September 30, 2008Edition Number: 13Section / Paragraph Reference: 4.8.6.3Subject: Minimum lead wire gauge si

3、ze for GU24 outlet-box lampholdersDECISION:The lead wires of an outlet-box lampholder shall not be smaller than 16 AWG (1.3 mm2).Exception: This requirement does not apply to outlet-box lampholders provided with GU24 or GU24-1lampholders.RATIONALE FOR DECISION:The minimum 16 AWG lead wire requiremen

4、t for outlet box lampholders goes back to the eleventh editionof UL 496 when the scope of the standard was limited to Edison-base lampholders. Although therequirement was carried through subsequent revisions of the standard when the scope was extended toinclude fluorescent lampholders, it did not an

5、ticipate GU24 outlet-box lampholders.The current-carrying capacity of 16 AWG conductors is suitable for screw lampholders that can be ratedup to 600 Volts, with a maximum power rating of 660 Watts for medium or 2000 Watts for mogul bases.GU24 lampholders on the other hand are limited to 300 V by ANS

6、I_ANSLG C81.62 and intended forenergy efficient lamp loads of less than 100 Watts. Furthermore, Clause SA2.3 of UL 496 prohibitsbase-to-base adapters that would allow a GU24 holder to accept an Edison screw-base. It should also benoted that an independent proposal to limit the rating of GU24 lamphol

7、ders to 300 Watts has alreadygained STP consensus.In conclusion, 18 AWG lead wires have sufficient current carrying capacity for GU24 lampholders andshould be permitted for this application. This is consistent with the requirements for fluorescent luminairesand lighting components such as ballasts a

8、nd LED drivers that are directly connected to a branch circuit.Copyright 2013 Underwriters Laboratories Inc.UL, in performing its functions in accordance with its objectives, does not guarantee or warrant thecorrectness of Certification Requirement Decisions it may issue or that they will be recogni

9、zed or adoptedby anyone. Certification Requirement Decisions are the opinion of Underwriters Laboratories Inc. inpractically applying the requirements of the standard. They do not represent formal interpretations of thestandard under American National Standards Institute (ANSI) processes. UL shall n

10、ot be responsible toanyone for the use of or reliance upon Certification Requirement Decisions by anyone. UL shall not incurany obligation or liability for damages, including consequential damages, arising out of or in connectionwith the use or reliance upon Certification Requirement Decisions. The

11、electronic version of theCertification Requirement Decision is the current version and previously printed copies may be outdated.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULThis document is published as a service to ULs certification customersSTANDARD NUMBER: UL 496 -2-