TIA-574-1990 9-Position Non-Synchronous Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange《数字终端设备和数据电路终端设备 使用.pdf

《TIA-574-1990 9-Position Non-Synchronous Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange《数字终端设备和数据电路终端设备 使用.pdf》由会员分享，可在线阅读，更多相关《TIA-574-1990 9-Position Non-Synchronous Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange《数字终端设备和数据电路终端设备 使用.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA-574-1990 APPROVED: MARCH 26, 1990 REAFFIRMED: DECEMBER 10, 1998 REAFFIRMED: MAY 20, 2003 REAFFIRMED: DECEMBER 7, 2012 TIA-574 September 19909-Position Non-Synchronous Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data InterchangeNOTICE

2、TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the

3、proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Pub

4、lications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, n

5、or does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate s

6、afety and health practices and to determine the applicability of regulatory limitations before its use. (From Project No. 3-4094-RF3, formulated under the cognizance of the TIA TR-30.2 Subcommittee on DTE-DCE Interfaces and Protocols.) Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Technology

7、(b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may invo

8、lve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a st

9、atement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or cond

10、itions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respe

11、cts the Document or its contents. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise)

12、, whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Engineering Manual, 4thedition) then (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Ref

13、erence; (ii) TIAs policy of encouragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and published pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identi

14、fication to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the co

15、ntents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS IN

16、TELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODU

17、CT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDE

18、NTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING

19、NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. STD-EIA TIA-57q-ENGL 1770 3234b00 Ob1390b L7q EIA/TIA-574 CONTENTS 1 .SCOPE . i 1.1 GENERAL 1 1.2 CONNECTION . 1 1.3 BITSEQUENCES 1 1.4 DATA SIGN

20、ALING RATES . 1 1.5 NON-SYNCHRONOUS COMMUNICATION . 1 1.6 CLASSES OF SERVICE 1 2 . INTERFACE MECHANICAL CHARACTERISTICS 2 2.1 POINT OF INTERFACE 2 2.2 INTERFACE CONNECTOR . 2 2.3 CONNECTOR CONTACT ASSIGNMENTS 7 3 . FUNCTIONAL DESCRIPTIONS OF THEINTERCHANGE CIRCUITS 8 3.1 GENERAL 8 3.2 CLASSIFICATION

21、 OF CIRCUITS . 8 3.3 SIGNAL CHARACTERISTICS, GENERAL 9 3.4 DEFINITIONS OF INTERCHANGE CIRCUITS 9 LIST OF FIGURES Figure 2.1 . 2 Figure2.2 . 3 Figure23 . 4 Figure2.4 . 5 Figure2.5 . 6 Figure2.6 . 6 Figure2.7 . 7 Figure3.1 . 8 ii STD-EIA TIA-57Y-ENGL 1770 m 323Yb00 Ob13707 000 m EIA/TIA-574 Page 1 SEC

22、TION ONE 1. SCOPE 1.1 GENERAL This Standard is applicable to the interconnection of data terminating equipment (DTE) and data circuit-terminating equipment (DCE) employing serial binary data interchange where a minimal number of control and information circuits are required. It defies: Section 1 - S

23、cope Section 2 - Interface Mechanical Characteristics Section 3 - Functional Description of the Interchange Circuits The electrical characteristics applicable to this interface can be found in AMERICAN NATIONAL STANDARD ANSI/EIA/TIA-562. 1.2 CONNECTION When used in conjunction with the above mention

24、ed electrical characteristics standard, this Standard applies where equipment on one side of the DTE/DCE interface is intended for connection directly to the other side without additional technical considerations. 1.3 BIT SEQUENCES This Standard applies to data communication systems where data is bi

25、t serialized by the DTE and the DCE and places no restrictions on the arrangement or the sequence of bits. 1.4 DATA SIGNALING RATES This Standard is applicable for use at all data signaling rates supported by EIA/TIA-562. 1.5 NON-SYNCHRONOUS COMMUNICATION This Standard applies to non-synchronous ser

26、ial binary data communication systems. 1.6 CLASSES OF SERVICE This Standard applies to switched, non-switched, dedicated, leased or private line service, either two-wire or four-wire. Consideration is given both to point-tepoint and multipoint operation. EIA/TIA-574 Page 2 SECTION TWO 2. INTERFACE M

27、ECHANICAL CHARACTERISTICS 2.1 POINT OF INTERFACE The interface between the DTE and the DCE is located at a pluggable connector signal interface point between the two equipments (see Figure 2.1). A %position connector is specified for this interface. Figure 2.1 Point of Interface The DTE shall be pro

28、vided with a male connector as specified in Section 2.2. An interface cable terminated in a female connector as specified in Section 2.2 should be provided for connection to the DCE. The configuration for connection of the interface cable at a point other than the point of demarcation is not specifi

29、ed. NOTE: When additional functions are provided in a separate unit inserted between the DTE and the DCE, the male connector shall be associated with the side of the unit which interfaces with the DTE. A cable with a female connector shall be provided on the side of the unit which interfaces the DCE

30、. 2.2 INTERFACE CONNECTOR Figure 2.2 illustrates the cable interface connector which has female contacts (sockets) and a male shell (receptical). Figure 2.3 illustrates the DTE connector which has male contacts (pins) and a female shell (plug). These figures also illustrate the contact numbering. Fi

31、gures 2.4, 2.5 and 2.6 illustrate contact spacing and dimensions. STD-EIA TIA-574-ENGL L770 m 323qb00 ObL3707 783 m 16.46 16.21 EIA/TIA-574 Page 3 Figure 2.2 Cable Interface Connector EIA/TIA-574 Page 4 R 2.69 17.04 16.79 - r I Figure 2.3 DTE Interface Connector EIA/TIA-574 Page 5 L5.49 Dimensions i

32、n mi 11 imetres Figure 2.4 Insert Dimensions EU f TIA-574 Page 6 10.03 -+=“ Figure 2.5 Contact Specification - Male 9.63 c “ “- When the pin is mated with the socket, sufficient applied by the socket to ensure proper electrical force shall be contact. Figure 2.6 Contact Specification - Female 4 STD-

33、EIA TIA-57q-ENGL L770 m 3234b00 Ob13713 304 m 2.3 CONNECTOR CONTACT ASSIGNMENTS Contact Number 1 2 3 4 5 6 7 8 9 Circuit 109 104 103 10812 102 107 105/133 106 125 Description Received Line Signal Detector Received Data Transmitted Data DTE Ready Signal Common DCE Ready Request to Send/Ready for Rece

34、iving Clear to Send Ring Indicator Figure 2.7 EIA/TIA-574 Page 7 Connector Contact Assignments Note: When hardware flow control is required Circuit 105 may take on the functionality of Circuit 133. EIA/TIA-574 Page 8 SECTION THREE 3. FUNCTIONAL DESCRIPTIONS OF THE INTERCHANGE CIRCUITS 3.1 GENERAL Th

35、is Section defines the basic interchange circuits that apply, collectively, to all systems. 3.2 CLASSIFICATION OF CIRCUITS Each interchange circuit is characterized as one of the three following types: Signal Common Data Control A list of interchange circuits specifying the circuit number, name, typ

36、e and direction relative to the DCE, of each, is presented in Figure 3.1. Number Name 102 Sianal Common 103 Transmitted Data 104 Received Data 105 Request to Send 106 Clear To Send 107 DCE Ready 108/2 DTE Ready 133 Ready for Receiving 125 Ring Indicator 109 Received Line Signal Detector Circuit Dire

37、ction To DCE From DCE To DCE From DCE From DCE To DCE From DCE To DCE From DCE Circuit Type Signal Common Data Data Control Control Control Control Control Control Control Figure S.1 Interchange Circuits by Category STD-EIA TIA-574-ENGL L770 m 3234b00 Ob13715 L87 m EIA/TIA-574 Page 9 3.3 SIGNAL CHAR

38、ACTERISTICS, GENERAL Interchange circuits transferring data across the interface shall hold MARK (binary ONE) or SPACE (binary ZERO) conditions for the total nominal duration of each signal element. Distortion tolerances axe set forth in EIA-404A, Standard for Start-Stop Signal Quality for Non- sync

39、hronous Data Terminal Equipment. 3.4 DEFINITIONS OF INTERCHANGE CIRCUITS Circuit 102 - Signal Common Direction - not applicable This circuit establishes the common reference potential for all interchange circuits. Within the DCE, this circuit shall be brought to one point and it shall be possible to

40、 connect this point to Protective Ground by means of a wire strap inside the equipment. This wire strap may be connected or removed, at installation, as required to meet applicable regulations or to minimize the introduction of noise into the electronic circuitry. This strap may be paralleled by an

41、impedance (high at low frequencies) to provide, when the strap is removed, for immunity to static discharges or for other purposes. Circuit 105 - Transmitted Data Direction - To the DCE Signals on this circuit are generated by the DTE and transferred to the local DCE for transmission to remote DTEs

42、or for maintenance or control of the local DCE. The DTE shall hold Circuit 103 in the binary ONE (MARK) condition at all times when no data or maintenance or control signals are being transferred across the interface. In all systems, except as noted below, the DTE shall not transfer data across the

43、interface unless an ON condition exists on all of the following Circuits (where they axe implemented): - Circuit 105, Request to Send - Circuit 106, Clear to Send - Circuit 107, DCE Ready - Circuit 108/2, DTE Ready In DTEs supporting serial dialing DCEs, programming or control signals maybe transfer

44、red across the interface on Circuit 103 when the conditions listed below exist for the Circuits specified (where they are implemented): - Circuit 106, Clear to Send = ON - Circuit 107, DCE Ready = OFF - Circuit 108/2, DTE Ready = ON EIA/TIA-574 Page 10 Circuit 104 - Received Data Direction - From th

45、e DCE Signals on this circuit are generated by the receiving DCE in response to data signals received from the remote DCE, or in response to maintenance or control signals from the local DTE. Circuit 104 shall be held in the binary ONE (MARK) condition at all times when Circuit 109 (Received Line Si

46、gnal Detector) is in the OFF condition. In half-duplex operation, Circuit 104 shall be held in the binary ONE (MARK) condition when Circuit 105 (Request to Send) is ON and for a brief interval following the ON to OFF transition of Circuit 105 to allow for the completion of transmission (see Circuit

47、103 - Transmitted Data) and the decay of line reflections. Circuit 105 - Request to Send Direction - To the DCE This circuit is used to condition the local DCE for data transmission and on a half-duplex channel, to control the direction of data transmission of the local DCE. In one-way or duplex ope

48、ration, the ON condition maintains the DCE in the transmit mode. The OFF condition maintains the DCE in a non-transmit mode. In half-duplex operation, the ON condition maintains the DCE in the transmit mode and inhibits the receive mode. The OFF condition maintains the DCE in the receive mode. A tra

49、nsition from OFF to ON instructs the DCE to enter the transmit mode. The DCE responds by taking such action as may be necessary and indicates completion of such action by turning ON Circuit 106 (Clear to Send), thereby indicating to the DTE that data may be transferred across the interface on Circuit 103 (Transmitted Data). A transition from ON to OFF instructs the DCE to complete the transmission of all data which was previously transferred across the interface on interchange Circuit 103 and then assume a non-transmit mode or a receive mode as appropriate. The DCE respond