SANS 50025-5-2009 Hot rolled products of structural steels Part 5 Technical delivery conditions for structural steels with improved atmospheric corrosion resistance《热轧结构钢产品 第5部分 改进.pdf

《SANS 50025-5-2009 Hot rolled products of structural steels Part 5 Technical delivery conditions for structural steels with improved atmospheric corrosion resistance《热轧结构钢产品 第5部分 改进.pdf》由会员分享，可在线阅读，更多相关《SANS 50025-5-2009 Hot rolled products of structural steels Part 5 Technical delivery conditions for structural steels with improved atmospheric corrosion resistance《热轧结构钢产品 第5部分 改进.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21932-1 SANS 50025-5:2009 Edition 1 EN 10025-5:2004 Edition 1SOUTH AFRICAN NATIONAL STANDARD Hot rolled products of structural steels Part

4、 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance This national standard is the identical implementation of EN 10025-5:2004 and is adopted with the permission of CEN, rue de Stassart 36, B-1050 Brussels. Published by SABS Standards Division 1 Dr L

5、ategan Road Groenkloof Private Bag X191 Pretoria 0001 Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 50025-5:2009 Edition 1 EN 10025-5:2004 Edition 1 Table of changes Change No

6、. Date Scope National foreword This South African standard was approved by National Committee SABS TC 1077, Engineering materials Ferrous metals, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in Feb

7、ruary 2009. This standard may only be used and printed by approved subscription and freemailing clients of the SABS. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10025-5 November 2004 ICS 77.140.10; 77.140.50 Supersedes EN 10155:1993 English version Hot rolled products of structural steels -

8、 Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance Produits lamins chaud en aciers de construction - Partie 5: Conditions techniques de livraison pour les aciers de construction rsistance amliore la corrosion atmosphrique Warmgewalzte Erzeugni

9、sse aus Bausthlen - Teil 5: Technische Lieferbedingungen fr wetterfeste Bausthle This European Standard was approved by CEN on 1 April 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a nati

10、onal standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in an

11、y other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finla

12、nd, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR

13、NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10025-5:2004: EThis standard may only be used and printed by approved subscription and freemailing clients of the S

14、ABS.EN 10025-5:2004 (E) 2 Contents Page Foreword4 1 Scope 5 2 Normative references 5 2.1 General standards .5 2.2 Standards on dimensions and tolerances (see 7.7.1)6 2.3 Standards on testing .6 3 Terms and definitions .6 4 Classification and designation.7 4.1 Classification7 4.1.1 Main quality class

15、es 7 4.1.2 Grades and qualities .7 4.2 Designation 7 5 Information to be supplied by the purchaser .8 5.1 Mandatory information8 5.2 Options .8 6 Manufacturing process .8 6.1 Steel making process8 6.2 Deoxidation 9 6.3 Delivery conditions9 7 Requirements.9 7.1 General9 7.2 Chemical composition 9 7.3

16、 Mechanical properties.9 7.3.1 General9 7.3.2 Impact properties.10 7.3.3 Improved deformation properties perpendicular to the surface 10 7.4 Technological properties 10 7.4.1 Weldability10 7.4.2 Formability10 7.5 Surface properties .11 7.5.1 Strip.11 7.5.2 Plates and wide flats .11 7.5.3 Sections 11

17、 7.5.4 Bars and rods.11 7.6 Internal soundness11 7.7 Dimensions, tolerances on dimensions and shape, mass12 8 Inspection.12 8.1 General12 8.2 Type of inspection and inspection document 12 8.3 Frequency of testing .12 8.3.1 Sampling.12 8.3.2 Test units12 8.3.3 Verification of chemical composition12 8

18、.4 Tests to be carried out for specific inspection.12 9 Preparation of samples and test pieces13 9.1 Selection and preparation of samples for chemical analysis .13 9.2 Location and orientation of samples and test pieces for mechanical tests13 9.2.1 General13 9.2.2 Preparation of samples .13 This sta

19、ndard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 10025-5:2004 (E) 3 9.2.3 Preparation of test pieces.13 9.3 Identification of samples and test pieces .13 10 Test methods .13 10.1 Chemical analysis13 10.2 Mechanical tests 14 10.3 Ultrasonic testing 14

20、 10.4 Retests14 11 Marking, labelling, packaging 14 12 Complaints .14 13 Options (see 5.2)14 Annex A (informative) List of corresponding former designations 22 Annex B (informative) List of national standards which correspond with EURONORMS referenced 23 Annex C (informative) Additional information

21、for the use of steel with improved atmospheric corrosion resistance .24 Annex D (informative) Notes on fabrication 25 Bibliography26 This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 10025-5:2004 (E) 4 Foreword This document (EN 10025-5:2004)

22、has been prepared by Technical Committee ECISS/TC 10 “Structural steels - Grades and qualities”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2005,

23、and conflicting national standards shall be withdrawn at the latest by May 2005. This document supersedes together with EN 10025-1:2004, EN 10155:1993, Structural steels with improved atmospheric corrosion resistance - Technical delivery conditions. The titles of the other parts of this document are

24、: Part 1: General technical delivery conditions; Part 2: Technical delivery conditions for non-alloy structural steels; Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels; Part 4: Technical delivery conditions for thermomechanical rolled weld

25、able fine grain structural steels; Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition. This document has been prepared under Mandate M/120 given to CEN by the European Commission and the European Free Trade Associat

26、ion, and supports essential requirements of the EU Construction Products Directive (89/106/EEC). For relationship with the EU Construction Products Directive, see informative Annex ZA of EN 10025-1:2004. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the f

27、ollowing countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerlan

28、d and the United Kingdom. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 10025-5:2004 (E) 5 1 Scope Part 5 of this document, in addition to part 1, specifies requirements for flat and long products of hot rolled steels with improved atmosph

29、eric corrosion resistance in the grades and qualities given in Tables 2 and 3 (chemical composition) and Tables 4 and 5 (mechanical properties) in the usual delivery conditions as given in 6.3. The thicknesses in which products of the steel grades and qualities specified in this document may be supp

30、lied are given in Table 1. In addition to EN 10025-1:2004 the steels specified in this document are especially intended for use in welded, bolted and riveted components which shall have enhanced resistance to atmospheric corrosion, for service at ambient temperatures (subject to the restrictions des

31、cribed in 7.4.1). The steels specified in this Part 5 are not intended to be heat treated except products delivered in the delivery condition +N. Stress relief annealing is permitted (see also the NOTE in 7.3.1.1 of EN 10025-1:2004). Products delivered in +N condition can be hot formed and/or normal

32、ized after delivery (see Clause 3). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)

33、 applies. 2.1 General standards EN 10020, Definition and classification of grades of steel. EN 10025-1:2004, Hot rolled products of structural steels - Part 1: General technical delivery conditions. EN 10027-1, Designation systems for steels - Part 1: Steel names, principal symbols. EN 10027-2, Desi

34、gnation systems for steels - Part 2: Numerical system. EN 10163-1, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections Part 1: General requirements. EN 10163-2, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections

35、 Part 2: Plates and wide flats. EN 10163-3, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections Part 3: Sections. EN 10164, Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions. EN

36、10221, Surface quality classes for hot-rolled bars and rods - Technical delivery conditions. CR 10260, Designation systems for steels - Additional symbols. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 10025-5:2004 (E) 6 2.2 Standards on d

37、imensions and tolerances (see 7.7.1) EN 10017, Non-alloy steel rod for drawing and/or cold rolling Dimensions and tolerances. EN 10024, Hot rolled taper flange I sections - Tolerances on shape and dimensions. EN 10029, Hot rolled steel plates 3 mm thick or above - Tolerances on dimensions, shape and

38、 mass. EN 10034, Structural steel I and H sections - Tolerances on shape and dimensions. EN 10048, Hot rolled narrow steel strip - Tolerances on dimensions and shape. EN 10051, Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels - Tolerances on dimensions and shape.

39、 EN 10055, Hot-rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions. EN 10056-1, Structural steel equal and unequal leg angles - Part 1: Dimensions. EN 10056-2, Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and d

40、imensions. EN 10058, Hot rolled flat steel bars for general purposes - Dimensions and tolerances on shape and dimensions. EN 10059, Hot rolled square steel bars for general purposes - Dimensions and tolerances on shape and dimensions. EN 10060, Hot rolled round steel bars for general purposes - Dime

41、nsions and tolerances on shape and dimensions. EN 10061, Hot rolled hexagon steel bars for general purposes - Dimensions and tolerances on shape and dimensions. EN 10067, Hot rolled bulb flats - Dimensions and tolerances on shape, dimensions and mass. EN 10162, Cold rolled steel sections - Technical

42、 delivery conditions - Dimensional and cross-sectional tolerances. EN 10279, Hot rolled steel channels - Tolerances on shape and dimensions. 2.3 Standards on testing EN 10160, Ultrasonic testing of steel flat product of thickness equal to or greater than 6 mm (reflection method). EN 10306, Iron and

43、steel - Ultrasonic testing of H beams with parallel flanges and IPE beams. EN 10308, Non-destructive testing - Ultrasonic testing of steel bars. EN ISO 643, Steels Micrographic determination of the apparent grain size (ISO 643:2003). 3 Terms and definitions For the purposes of this document, the ter

44、ms and definitions given in EN 10025-1:2004 and the following apply. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.EN 10025-5:2004 (E) 7 3.1 normalizing rolling rolling process in which the final deformation is carried out in a certain temper

45、ature range leading to a material condition equivalent to that obtained after normalizing so that the specified values of the mechanical properties are retained even after normalizing The abbreviated form of this delivery condition is +N. NOTE In international publications for both the normalizing r

46、olling, as well as the thermomechanical rolling, the expression “controlled rolling“ may be found. However in view of the different applicability of the products a distinction of the terms is necessary. 3.2 as-rolled delivery condition without any special rolling and/or heat treatment condition The

47、abbreviated form of this delivery condition is +AR. 3.3 steel with improved atmospheric corrosion resistance steel in which a certain number of alloying elements, such as P, Cu, Cr, Ni, Mo, has been added in order to increase its resistance to atmospheric corrosion, by forming an auto-protective oxi

48、de layer on the base metal under the influence of weather conditions NOTE 1 Steel with improved atmospheric corrosion resistance is often called weathering steel. NOTE 2 Additional information for the use of steel with improved atmospheric corrosion resistance is given in Annex C. 4 Classification a

49、nd designation 4.1 Classification 4.1.1 Main quality classes The steel grades specified in this document shall be classified as alloy special steels according to EN 10020. 4.1.2 Grades and qualities This document specifies the steel grades S235 and S355 (see Table 5), which differ in their mechanical properties. The steel grades may be supplied in qualities J0, J2 and K2. The qualities differ in specified impact energy requirements. Grade S355 is subdivided into the classes W and WP, which differ mainly in their carbon and phosphorus contents (see Tables