SANS 15614-3-2009 Specification and qualification of welding procedures for metallic materials - Welding procedure test Part 3 Fusion welding of non-alloyed and low-alloyed cast ir.pdf

《SANS 15614-3-2009 Specification and qualification of welding procedures for metallic materials - Welding procedure test Part 3 Fusion welding of non-alloyed and low-alloyed cast ir.pdf》由会员分享，可在线阅读，更多相关《SANS 15614-3-2009 Specification and qualification of welding procedures for metallic materials - Welding procedure test Part 3 Fusion welding of non-alloyed and low-alloyed cast ir.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-22418-9 SANS 15614-3:2009 Edition 1 ISO 15614-3:2008 Edition 1SOUTH AFRICAN NATIONAL STANDARD Specification and qualification of welding p

4、rocedures for metallic materials Welding procedure test Part 3: Fusion welding of non-alloyed and low-alloyed cast irons This national standard is the identical implementation of ISO 15614-3:2008 and is adopted with the permission of the International Organization for Standardization. Published by S

5、ABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001 Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 15641-3:2009 Edition 1 ISO 15614-3:2008 Editio

6、n 1 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS TC 44, Welding and allied processes, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document

7、was published in March 2009. This standard may only be used and printed by approved subscription and freemailing clients of the SABS. Reference number ISO 15614-3:2008(E) ISO 2008INTERNATIONAL STANDARD ISO 15614-3 First edition 2008-03-15 Specification and qualification of welding procedures for met

8、allic materials Welding procedure test Part 3: Fusion welding of non-alloyed and low- alloyed cast irons Descriptif et qualification dun mode opratoire de soudage pour les matriaux mtalliques preuve de qualification dun mode opratoire de soudage Partie 3: Soudage par fusion des fontes non allies et

9、faiblement alliesSANS 15614-3:2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 15614-3:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed bu

10、t shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this

11、area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for us

12、e by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in

13、any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22

14、749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reservedSANS 15614-3:2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 15614-3:2008(E) ISO 2008 All rights reserved iii Contents Page Forewo

15、rd iv Introduction v 1 Scope1 2 Normative references1 3 Terms and definitions .2 4 Welding processes3 5 Preliminary welding procedure specification .3 6 Welding procedure test.3 7 Test piece.3 7.1 General3 7.2 Shape and dimensions of test piece .4 7.3 Welding of test piece.4 8 Examination and testin

16、g .5 8.1 Extent of testing.5 8.2 Location and taking of test specimens .6 8.3 Non-destructive testing.6 8.4 Destructive tests6 8.5 Acceptance criteria7 8.6 Re-testing.7 9 Range of qualification .7 9.1 General7 9.2 Qualification related to the manufacturer .7 9.3 Qualification related to the material

17、.8 9.4 Qualification common to all welding procedures 10 9.5 Qualification specific to processes .12 10 Welding procedure qualification record form.13 Annex A (informative) Welding procedure qualification record form.14 Bibliography 17 SANS 15614-3:2009This standard may only be used and printed by a

18、pproved subscription and freemailing clients of the SABS.ISO 15614-3:2008(E) iv ISO 2008 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is n

19、ormally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part i

20、n the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prep

21、are International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that s

22、ome of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15614-3 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 121, Welding, in collaboration with Techn

23、ical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 10, Unification of requirements in the field of metal welding, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Requests for official interpretations of any aspect of this part of

24、 ISO 15614 should be directed to the Secretariat of ISO/TC 44/SC 10 via your national standards body. A complete listing of these bodies can be found at www.iso.org. ISO 15614 consists of the following parts, under the general title Specification and qualification of welding procedures for metallic

25、materials Welding procedure test: Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys Part 2: Arc welding of aluminium and its alloys Part 3: Fusion welding of non-alloyed and low-alloyed cast irons Part 4: Finishing welding of aluminium castings Part 5: Arc welding of

26、titanium, zirconium and their alloys Part 6: Arc and gas welding of copper and its alloys Part 7: Overlay welding Part 8: Welding of tubes to tube-plate joints Part 10: Hyperbaric dry welding Part 11: Electron and laser beam welding Part 12: Spot, seam and projection welding Part 13: Resistance butt

27、 and flash welding SANS 15614-3:2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 15614-3:2008(E) ISO 2008 All rights reserved v Introduction Details of International Standards dealing with specification and qualification of welding proce

28、dures are given in ISO 15607:2003, Annex A. Welding procedure tests for flash welding are presented in ISO 15614-13 and for friction welding in ISO 15620. SANS 15614-3:2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 15614-3:2009This st

29、andard may only be used and printed by approved subscription and freemailing clients of the SABS.INTERNATIONAL STANDARD ISO 15614-3:2008(E) ISO 2008 All rights reserved 1Specification and qualification of welding procedures for metallic materials Welding procedure test Part 3: Fusion welding of non-

30、alloyed and low-alloyed cast irons 1 Scope This part of ISO 15614 specifies how a preliminary welding procedure specification (pWPS) for production and repair welding of non-alloyed and low-alloyed cast irons is qualified by fusion welding procedure tests. This part of ISO 15614 defines the conditio

31、ns for execution of the welding procedure tests and the range of qualification for welding procedures for all practical welding operations within the range of a defined list of variables. This part of ISO 15614 is applicable to all new welding procedures. However, it does not invalidate previous wel

32、ding procedure tests made to former national standards or specifications. Where additional tests have to be carried out to make the qualification technically equivalent, it is only necessary to do the additional tests on a test piece made in accordance with this part of ISO 15614. Additional tests m

33、ay be required by application standards. This part of ISO 15614 is applicable to welding non-alloyed and low-alloyed grey cast iron castings according to: EN 1561; EN 1562; EN 1563; and EN 1564. The principles of this part of ISO 15614 are also applicable for welding cast iron to steel or to other u

34、nalloyed and low-alloyed cast iron materials. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any a

35、mendments) applies. ISO 783, Metallic materials Tensile testing at elevated temperature ISO 6947, Welds Working positions Definitions of angles of slope and rotation ISO 14175, Welding consumables Gases and gas mixtures for fusion welding and allied processes ISO 15607:2003, Specification and qualif

36、ication of welding procedures for metallic materials General rules ISO 15609-1, Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding ISO 15609-2, Specification and qualification of welding procedures for metallic materials W

37、elding procedure specification Part 2: Gas welding SANS 15614-3:2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 15614-3:2008(E) 2 ISO 2008 All rights reservedISO 15611, Specification and qualification of welding procedures for metallic

38、materials Qualification based on previous welding experience ISO 15613, Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test EN 571-1, Non destructive testing Penetrant testing Part 1: General principles EN 970, Non-destructi

39、ve examination of fusion welds Visual examination EN 1011-1, Welding Recommendations for welding of metallic materials Part 1: General guidance for arc welding EN 1011-8:2004, Welding Recommendations for welding of metallic materials Part 8: Welding of cast irons EN 1321, Destructive tests on welds

40、in metallic materials Macroscopic and microscopic examination of welds EN 1561, Founding Grey cast irons EN 1562, Founding Malleable cast irons EN 1563, Founding Spheroidal graphite cast irons EN 1564, Founding Austempered ductile cast irons EN 10002-1, Metallic materials Tensile testing Part 1: Met

41、hod of test at ambient temperature 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 15607 and the following apply. 3.1 production welding any welding carried out during manufacture before final delivery to the end user 3.2 joint welding production wel

42、ding used to join components together 3.3 finishing welding production welding carried out in order to remove casting defects to ensure the required quality of castings 3.4 repair welding any welding carried out after delivery to the end user, i.e. after the product has been in service SANS 15614-3:

43、2009This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO 15614-3:2008(E) ISO 2008 All rights reserved 34 Welding processes Welding is covered by the following welding processes in accordance with ISO 4063: 111 manual metal arc welding (metal arc

44、 welding with covered electrode); shielded metal arc welding (USA); 114 self-shielded tubular-cored arc welding; 121 submerged arc welding with one wire electrode; 131 metal inert gas welding, MIG welding; gas metal arc welding (USA); 135 metal active gas welding, MAG welding; gas metal arc welding

45、(USA); 136 tubular-cored metal arc welding with active gas shield; flux cored arc welding (USA); 141 tungsten inert gas welding; TIG welding; gas tungsten arc welding (USA); 15 plasma arc welding; 311 oxy-acetylene welding; oxyacetylene welding (USA). 5 Preliminary welding procedure specification (p

46、WPS) The pWPS shall be prepared in accordance with ISO 15609-1 or ISO 15609-2. 6 Welding procedure test The welding and testing of test pieces shall be in accordance with Clauses 7 and 8. The welder or welding operator, who undertakes the welding procedure test satisfactorily in accordance with this

47、 part of ISO 15614, is qualified to weld within the range of qualification according to Clause 9. 7 Test piece 7.1 General The test piece shall comply with the requirements of 7.2, 7.3, and Figure 1. It can be cast separately or removed from the casting/component. Preparation of sufficiently large t

48、est pieces is by machining. When the standardized test pieces as shown in this part of ISO 15614 do not represent the production/joint geometry, the use of ISO 15611 or ISO 15613 shall be required. SANS 15614-3:2009This standard may only be used and printed by approved subscription and freemailing c

49、lients of the SABS.ISO 15614-3:2008(E) 4 ISO 2008 All rights reservedDimensions in millimetres Key 1 discard 2 inspection length The dimensions shown are for information only and may be adjusted to meet production and testing requirements. The edges of the groove should be smooth rounded. Edge preparation of the groove and fit-up shall be as detailed in the pWPS. aIn accordance with Table 3 or Table 4. ba = 5 mm to 15 mm or = 5 to 20. Figure 1 T