SAE J 3052-2017 Brake Hydraulic Component Flow Rate Measurement for High Differential Pressure ( 5 bar).pdf

《SAE J 3052-2017 Brake Hydraulic Component Flow Rate Measurement for High Differential Pressure ( 5 bar).pdf》由会员分享，可在线阅读，更多相关《SAE J 3052-2017 Brake Hydraulic Component Flow Rate Measurement for High Differential Pressure ( 5 bar).pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising ther

2、efrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this

3、publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-49

4、70 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/J3052_201705 SURFACE VEHICLE RECOMMENDED PRACTICE J3052 MAY2017 Issued 2017-05 Brake Hydraulic

5、 Component Flow Rate Measurement for High Differential Pressure (5 bar) RATIONALE This recommended practice is intended to provide a standard method, test set up, and test conditions for measuring flow characteristics of brake fluid through brake components in a hydraulic brake circuit, in a high pr

6、essure differential flow regime. It maps flow rates through the test specimens, relative to the pressure differential across the test specimen. Data generated in accordance to this standard are intended to be useful towards hydraulic brake response time modeling, towards specifying flow characterist

7、ics in brake components to meet desired hydraulic system response characteristics, and diagnosing the contribution of individual hydraulic components to system level response behavior. FOREWORD This section details some key points used by the founding task force to set the parameters in this recomme

8、nded practice: Every effort was made to give the user flexibility to define the test specimen (as a component or subsystem comprised of multiple components) according to the measurement needs, but provide enough structure to ensure repeatable measurements from lab to lab. It is critical that a clear

9、 definition of the test specimen be determined before the test and documented with the test results. Two test classifications are defined, to fit with two commonly occurring needs for flow data, but with different priorities. The first classification seeks to establish uniform test conditions from l

10、ab to lab, so that components may be validated to a specification for flow characteristics. The second classification seeks to establish the most realistic in-vehicle test set-up, so that flow data may be generated to support system-level modeling activities. The task force recognized that the total

11、 duration of a flow event of interest will often be very short - sometimes tenths of a second or less, which makes the transient flow behavior during the build-up to peak pressure and the subsequent slow down as pressure levels equalize of interest. In addition, the volume flow rates with large pres

12、sure differentials can be quite high, making it difficult to maintain steady-state without suffering changes in fluid properties due to heating or cavitation. Therefore, the task force carefully considered the necessity of reproducing the transient flow (which would be done by forcing fluid into a c

13、losed volume with a step input) versus steady flow (which is the method recommended). By measuring flow through a common set of antilock brake hydraulic control units using both methods, and observing which method produced closer correlation of a brake system model to in-vehicle measured pressure re

14、sponse times, it was determined that the steady flow method produced closer correlation and more repeatable results. Generally, the steady flow method produced lower flow coefficients than the transient method. SAE INTERNATIONAL J3052 MAY2017 Page 2 of 11 1. SCOPE This recommended practice provides

15、a method, test set-up, and test conditions for brake hydraulic component flow rate measurement for high differential pressure (5 bar) flow conditions. It is intended for hydraulic brake components which affect the brake fluid flow characteristics in a hydraulic brake circuit, that are part of a circ

16、uit for which the flow characteristics are important to system operation, and that are exposed to high operating pressure differentials (in the 5 to 100 bar range). Typical applications may include measurement of flow through chassis controls valve bodies, orifices in the brake system such as in flo

17、w bolts, junction blocks, and master cylinders, and through brake pipe configurations. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest version of SAE publications shall apply. 2

18、.1.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. SAE J2994 Brake Hydraulic Component Low Pressure Flow Rate Measurement 3. TEST CLASSIFICATIONS Two diffe

19、rent test classifications are defined, each related to a different purpose for the testing. The classifications are listed below: 1. (Classification 1 - Component Validation) Flow rate measurement for comparison to specification, and for comparing one component design to another. a. Brake Fluid - us

20、e standard reference fluid RM6606. Test fluid properties are to be measured before test (viscosity, density, and water content). An alternate fluid may be used if agreed to by all stakeholders in the test result. b. Plumbing and test fixturing not part of test specimen - specified in sufficient deta

21、il to allow re-creation of test conditions. 2. (Classification 2 - Model Input Generation) Flow rate measurement to characterize flow through a component for modeling and performance diagnostics. a. Brake Fluid - Design intent fluid, test under design intent conditions. b. Test specimen will typical

22、ly be an entire subsystem (e.g., connection pipes to ESC unit, ESC unit itself, and piping to calipers). 4. HIGH PRESSURE DIFFERENTIAL TEST PROCEDURE 4.1 Test Apparatus Please refer to Figure A1 for a diagram of the test set-up and apparatus. Recommended specifications for some equipment may be foun

23、d in Appendix A (based on equipment used in the development of this recommended practice). SAE INTERNATIONAL J3052 MAY2017 Page 3 of 11 4.1.1 Test Specimen The object of the test may be a single component, such as the hydraulic control unit (HCU) of a slip control system, or it may be a set of compo

24、nents in series, such as the HCU in series with downstream piping and pipe connections. If the subject of the test is a single component, then any additional plumbing installed to connect the specimen to instrumentation shall be selected to have negligible flow resistance in comparison to the compon

25、ent on test (see 2.1.11). The definition of the test specimen may have an impact on the flow measurements - for example, a different flow vs. pressure drop behavior may be measured on an HCU, pipe, hose, and caliper/flow bolt setup versus measurement of the HCU by itself. It is important that what i

26、s considered the test specimen be well defined in the test documentation. 4.1.2 Pressure Source A hydraulic pressure source sized to maintain the desired peak pressure differential across the test specimens at the corresponding peak flow rate expected is required. A pump capable of delivering 100 cc

27、/s flow with a pressure head of 10000 kPa will be able to cover many automotive hydraulic component flow demands. The pump should be capable of holding a target pressure with an accuracy of 2%, and pressure pulses from the pump should also be less than 2% of the pressure target. An electrically driv

28、en, swashplate style pump (swashplate controls system pressure) with an electronic feedback-controlled servo valve (to control pressure upstream of the test specimen) has been found to be suitable for these measurements. 4.1.3 Environmental Enclosure The test specimen, the brake fluid supply, and th

29、e fluid-carrying portion of the test fixturing shall be enclosed in an environmental chamber capable of maintaining temperatures between -25 and 25 C. The required accuracy is +0 to -3 C. 4.1.4 Test Fixturing The test specimen, plumbing, and fluid reservoir shall be mounted in fixture to securely ho

30、ld the components in the intended position through the test. 4.1.5 Pressure Transducers The test rig shall be equipped with electronic pressure transducers for measuring the hydraulic pressure differential across the test specimen (the placement shall exclude the flow meter from the measurement). Th

31、e minimum required accuracy of the pressure transducer(s) is 0.2% of full scale accuracy. Full scale is recommended to be 1 bar. A minimum of two individual pressure transducers, or a differential pressure transducer, is required. 4.1.6 Flow Meter The test rig shall be equipped with an electronic fl

32、ow meter to record brake fluid flow through the test specimen. The flow meter is typically installed in between the test specimen and the differential pressure source. The minimum required accuracy 0.2% of full scale accuracy. The recommended range of the flow meter is 0 to 100 cc/s. 4.1.7 Thermocou

33、ples Thermocouples shall be installed in the test chamber and in the center of the fluid reservoir. 4.1.8 Viscometer (REQUIRED for Component Validation classification, optional for Model Input Generation classification). The test rig shall be equipped with a viscometer plumbed into the hydraulic cir

34、cuit downstream of the pressure. The viscometer shall be installed in a manner that allows measurement of the brake fluid viscosity while in test conditions (in the environmental chamber, if applicable) just prior to a flow rate measurement being conducted. It is acceptable to install the viscometer

35、 in parallel to the test specimen and to use valves to open and close the flow of fluid to the viscometer. SAE INTERNATIONAL J3052 MAY2017 Page 4 of 11 4.1.9 Junctions and Valves The use of junctions and valves should be minimized within the hydraulic flow path over which the pressure differential i

36、s measured (including the test specimen). Piping and tubing that is not part of the test specimen should be selected to minimize the flow disturbance within the test specimen (this generally means avoiding sudden transitions in pipe size, and keeping junctions and valves as far away from the test sp

37、ecimen as practicable). It is recommended that valves be of the ball or plug type (typically with a 90 turn from open to closed), with a seal design that can withstand temperatures down to -40 C. This type of valve will minimize the change in flow path cross-sectional area over the valve. 4.1.10 Tes

38、t Fixture Hydraulic Pipe Diameter The diameter of the piping in the hydraulic circuit outside of the test specimen can affect the flow measurement in two ways. (1) Fixture piping between the test specimen and either the upstream or the downstream pressure transducer can affect the flow characteristi

39、cs if not sized correctly, and (2) fixture piping that completes the hydraulic circuit outside of the pressure transducers can contribute to excessive heating of the working fluid (brake fluid) and/or limit the flow rates that can be achieved if not sized adequately. It is recommended that the next

40、larger industry standard size relative to the largest diameter pipe in the test specimen (if applicable) or relative to the largest port size (port size refers to the inner diameter of the flow passage of the port) in the test specimen (if applicable) be selected. Flow losses in fixture piping will

41、vary approximately according to the equations below: (Eq. 1) = 4 128 or (Eq. 2) = 128 4where: D = diameter of the pipe (m) = viscosity of the fluid (m 2 /s) = density of fluid (kg/m 3 ) L = length of the pipe in (m) Q = volumetric flow rate (m 3 /s) P = pressure drop over the pipe in (Pa) Example ca

42、lculation: For a section of fixture pipe between the upstream pressure transducer and the inlet port of the test specimen, such as an ABS module with the following parameters (note that the same calculation can be done separately for a section of fixture pipe between the outlet of the test specimen

43、and the downstream pressure transducer): D = 4.763 mm (0.004763 m) - 3/16-inch outside diameter = 0.000150 m 2 /s (DOT 3 at -25 C) = 1038 kg/m 3L = 10 cm (0.010 m) Q = 20 cc/s = 0.0002 m 3 /s P = 128 * 0.00002 * 0.000150 * 1038 * 0.01/( * 0.004763 4 ) = 2465 Pa = 24.7 millibar SAE INTERNATIONAL J305

44、2 MAY2017 Page 5 of 11 4.1.11 Test Specimen Installation and Orientation For best accuracy, the change in vertical position between pressure sensor locations and the test specimen inlet/outlet positions should be minimized. Due to the relatively large pressure differentials invoked in this procedure

45、, the error due to changes in vertical height of brake piping in the fixture that separates a pressure transducer from the intended inlet or output point of the test specimen is expected to be very small in most practical test set-ups. The correction equation offered in SAE J2994 is applicable here

46、and may be used in special cases where this error is expected to be appreciable. 4.1.12 Data Acquisition and Sample Rate The test rig shall be equipped with a digital data acquisition system capable of recording all specified measurements at a rate of at least 100 Hz. 4.2 Test Conditions 4.2.1 Tempe

47、rature Range Recommended temperatures for the test specimen and brake fluid specified below: Component Validation Classification: Temperatures to conduct testing are -25 C (25 C below zero) and 25 C. Test specimen and test fluid-containing portions of apparatus shall be soaked at temperature to insu

48、re a uniform temperature (see 2.4). Model Input Generation Classification: Temperatures to conduct testing are -25 C (25 C below zero), 0 C, and 25 C. Test specimen and test fluid-containing portions of apparatus shall be soaked at temperature to insure a uniform temperature (see 2.4). 4.2.2 Pressur

49、e Differential Recommended pressure differentials across the test specimen are according to test classification: Component Validation Classification: Test flow at 5, 10, 20, 30, 40, 50, 75, and 100 bar. Model Input Generation classification: The test requester may specify the pressure differential range and pressure inc