SAE J 2656-2016 Fastener Part Standard - Hexagon Socket Square Head and Slotted Headless Set Screws - Inch Dimensioned.pdf
《SAE J 2656-2016 Fastener Part Standard - Hexagon Socket Square Head and Slotted Headless Set Screws - Inch Dimensioned.pdf》由会员分享,可在线阅读,更多相关《SAE J 2656-2016 Fastener Part Standard - Hexagon Socket Square Head and Slotted Headless Set Screws - Inch Dimensioned.pdf(13页珍藏版)》请在麦多课文档分享上搜索。
1、 _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising ther
2、efrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2016 SAE International All rights reserved. No part of this
3、publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-49
4、70 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit HTTP:/STANDARDS.SAE.ORG/J2656_201611 SURFACE VEHICLE STANDARD J2656 NOV2016 Issued 2003-09 Revised 2016-11 Superseding
5、 J2565 JAN2010 Fastener Part Standard - Hexagon Socket, Square Head, and Slotted Headless Set Screws - Inch Dimensioned RATIONALE Section 2: Added and deleted reference documents. Figure 1: Field 8 Designator A deleted; Designator AH added; Designator B revised to note MIL-DTL-13924; Designator M4 d
6、eleted; Designator M added; Designator X3, X6, Y3 and Y6 deleted. Designator X added; Designator Z revised to note the option of ZA or ZC; Designator ZA and ZC added; Designator Z1, Z2, Z3 and Z4 deleted; Designator F added; Designator N added; Designator S added. Table 1: Updated to reflect hardnes
7、s requirements for non-ferrous set screws (ASTM F3042). Section 4: Revised coating notes due to coating changes. Reference document/requirements of F3042 added. Added six dot self-locking marking requirements for set screws greater than 3/8 inch. Section 5: Revised Black Oxide Caution Statement. 1.
8、SCOPE This SAE Part Standard covers selected inch dimensioned set screws manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever fasteners of t
9、he covered materials are used. This standard permits the fasteners to be identified and ordered by a part identification number (PIN) as defined in this document. 1.1 Purpose The purpose of this document is to assist the designer and other personnel in providing requirements and PINs for the most co
10、mmonly used set screws for ship systems and equipment. A PIN is normally required for all military applications and provides a useful means of communicating set screw requirements to suppliers and manufacturers in a very succinct manner. 1.2 Set Screw PINs This document provides PINs that can be use
11、d to identify set screws covered by this standard. The fasteners covered by this standard are manufactured in general accordance with materials and processes identified in standards issued by ASTM. The PIN identifies the thread form, type of head, type of drive, nominal diameter, special features (p
12、lating, locking elements), nominal length and fastener material. SAE INTERNATIONAL J2656 NOV2016 Page 2 of 13 1.3 Procurement Specification Safety - Hazardous Materials While the materials, methods, applications, and processes described or referenced in this specification may involve the use of haza
13、rdous materials, this specification does not address the hazards that may be involved in such use. It is the sole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of a
14、ll personnel involved. Certain elements and their compounds are considered hazardous or toxic materials by the United States (US) Environmental Protection Agency (EPA) and Occupational Safety and Health Agency (OSHA.) Users of these materials should consider special disposal and human exposure requi
15、rements in Title 40. Protection of the Environment, from the Code of Federal Regulations, and the special handling requirements invoked in Title 29, Occupational, Safety and Health, from the Code of Federal Regulations, respectively, and others as applicable. State and Local regulations may also app
16、ly. Some of the examples of certain elements and compounds are the following: mercury, boron, chromium, lead, silver, barium, cadmium and selenium. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this specification to the extent specified herein. Unless otherwise ind
17、icated, the latest issue of SAE publications shall apply. 2.1.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. SAE AMS2412 Plating, Silver Copper Strike, Lo
18、w Bake SAE AMS2487 Anodic Treatment of Titanium and Titanium Alloys - Solution pH 12.4 Maximum SAE AMS2488 Anodic Treatment - Titanium and Titanium Alloys - Solution pH 13 or Higher SAE AS1701 Lubricant, Solid Film SAE J2270 Ship Systems and Equipment - Threaded Fasteners - Inspection, Test, and Ins
19、tallation Guidance SAE J2280 Ship Systems and Equipment - Fasteners - Selection and Identification Requirements 2.1.2 AIA Publication Available from Aerospace Industries Association, 1000 Wilson Boulevard, Suite 1700, Arlington, VA 22209-3928, Tel: 703-358-1000, www.aia-aerospace.org. NAS1283 Fasten
20、ers, Male Threaded, Self-Locking 2.1.3 ASME Publications Available from ASME, P.O. Box 2900, 22 Law Drive, Fairfield, NJ 07007-2900, Tel: 800-843-2763 (U.S./Canada), 001-800-843-2763 (Mexico), 973-882-1170 (outside North America), www.asme.org. ASME B1.1 Unified Inch Screw Threads (UN and UNR Thread
21、 Form) ASME B18.3 Socket Cap, Shoulder, and Set Screws, Hex and Spline Keys (Inch Series) ASME B18.6.2 Slotted Head Cap Screws, Square Head Set Screws, and Slotted Headless Set Screws (Inch Series) ASME B18.12 Glossary of Terms for Mechanical Fasteners ASME B18.18 Quality Assurance for Fasteners SAE
22、 INTERNATIONAL J2656 NOV2016 Page 3 of 13 2.1.4 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org ASTM A342/A342M Standard Test Methods for Permeability of Weakly Magnetic Materials ASTM A380/A
23、380M Cleaning, Descaling and Passivation of Stainless Steel Parts, Equipment, and Systems ASTM A453/A453M High-Temperature Bolting, with Expansion Coefficients Comparable to Austenitic Stainless Steels ASTM B580 Anodic Oxide Coatings on Aluminum ASTM F788/F788M Surface Discontinuities of Bolts, Scre
24、ws, and Studs, Inch and Metric Series ASTM F880 Stainless Steel Socket, Square Head, and Slotted Headless-Set Screws ASTM F912 Alloy Steel Socket Set Screws ASTM F1136/F1136M Zinc/Aluminum Corrosion Protective Coatings for Fasteners ASTM F1470 Fastener Sampling for Specified Mechanical Properties an
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEJ26562016FASTENERPARTSTANDARDHEXAGONSOCKETSQUAREHEADANDSLOTTEDHEADLESSSETSCREWSINCHDIMENSIONEDPDF
链接地址:http://www.mydoc123.com/p-1027500.html