SAE AS 90347-2004 CABLE ASSEMBLY EXTERNAL ELECTRIC POWER AIRCRAFT 28 VOLT DC OPERATING POWER《飞机电缆组件外部电力为28 V直流电 工作电源 FSC 6150[代替 海军 MS90347 版本D 作废公告1 海军 MS903247 版本D 海军 MS90347 .pdf

《SAE AS 90347-2004 CABLE ASSEMBLY EXTERNAL ELECTRIC POWER AIRCRAFT 28 VOLT DC OPERATING POWER《飞机电缆组件外部电力为28 V直流电 工作电源 FSC 6150[代替 海军 MS90347 版本D 作废公告1 海军 MS903247 版本D 海军 MS90347 .pdf》由会员分享，可在线阅读，更多相关《SAE AS 90347-2004 CABLE ASSEMBLY EXTERNAL ELECTRIC POWER AIRCRAFT 28 VOLT DC OPERATING POWER《飞机电缆组件外部电力为28 V直流电 工作电源 FSC 6150[代替 海军 MS90347 版本D 作废公告1 海军 MS903247 版本D 海军 MS90347 .pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD CABLE ASSEMBLY, EXTERNAL ELECTRIC POWER, AIRCRAFT 28 VOLT DC, OPERATING POWER AS90347 ISSUED 2004-04REAFFIRMED 2009-09 CUSTODIAN: SAE AE-8/AE-8A FEDERAL SUPPLY CLASS6150 AS90347 SHEET 1 OF 4 NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MS90347, RE

2、VISION D AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MS90347, REVISION D. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION

3、 REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATI

4、ON OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUA

5、LIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT. Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored i

6、n a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Emai

7、l: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use

8、,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon thi

9、s Technical Report, please visit http:/www.sae.org/technical/standards/AS90347 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD CABLE ASSEMBLY, EXTERNAL ELECTRIC POWER, AIRCRAFT 28

10、VOLT DC, OPERATING POWER AS90347 AS90347SHEET 2 OF 4THIS SPECIFICATION IS APPROVED FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE.THE REQUIREMENTS FOR ACQUIRING THE PRODUCT(S) DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE ISSUE OF THE FOLLOWING SPECIFICATIO

11、N LISTED IN THAT ISSUE OF THE DODISS SPECIFIED IN THE SOLICITATION: MIL-C-7974. TABLE I. CABLE ASSEMBLY. TERMINALSPART NO. WIRESIZE POSITIVE NEGATIVE L FEET .5L METERS .15SUPERSEDESMS90347-7MS90347-8MS90347-9MS90347-10MS90347-11MS90347-120 MS20659-118 MS20659-13520 30 40 60 80 1006.10 9.14 12.1918.2

12、924.3830.48AN2551C20 & MS25488-6 & MS90347-1 AN2551C30 & MS25488-7 & MS90347-2 MS25488-8MS25488-9MS25488-10MS25488-11MS90347-13MS90347-14MS90347-15MS90347-16MS90347-17MS90347-1800 MS20659-120 MS20659-13620 30 40 60 80 1006.10 9.14 12.1918.2924.3830.48AN2551D20 & MS25488-12 & MS90347-3 AN2551D30 & MS

13、25488-13 & MS90347-4 MS25488-14MS25488-15MS25488-16MS25488-17MS90347-19MS90347-20MS90347-21MS90347-22MS90347-23MS90347-240000 MS20659-123 MS20659-12420 30 40 60 80 1006.10 9.14 12.1918.2924.3830.48AN2551E20 & MS25488-18 & MS90347-5 AN2551E20 & MS25488-19 & MS90347-6 MS25488-20MS25488-21MS25488-22MS2

14、5488-23Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD CABLE ASSEMBLY, EXTERNAL ELECTRIC POWER, AIRCRAFT 28 VOLT DC, OPERATING POWER AS90347 AS90347SHEET 3 OF 4TABLE II. SPLICE CRI

15、MP BARRELS (SEE DETAIL A) PART NO. WIRESIZEE FSHRINK TUBING X L (NOM) MS90347-25 0 .578/.558 .458/.438 1.00 X 5 MS90347-26 00 .640/.620 .520/.500 1.25 X 5 MS90347-27 0000 .784/.760 .645/.622 1.25 X 5 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or n

16、etworking permitted without license from IHS-,-,-AEROSPACE STANDARD CABLE ASSEMBLY, EXTERNAL ELECTRIC POWER, AIRCRAFT 28 VOLT DC, OPERATING POWER AS90347 AS90347SHEET 4 OF 4REQUIREMENTS: 1. MATERIAL: SEE ACQUISITION SPECIFICATION. 2. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECI

17、MALS .025 (0.64MM). 3. MOLDED-ON PLUGS, WHEN USED, SHALL MEET ALL THE REQUIREMENTS OF MS25488 EXCEPT THEY SHALL BE MOLDED TO THE CABLES. 4. THE LAST IDENTIFIER OF THE CABLE ASSEMBLY PART NUMBER SHALL BE “A“ TO INDICATE AN ATTACHABLE PLUG OR “M“ TO INDICATE AN INTEGRALLY MOLDED PLUG. 5. CABLE ASSEMBL

18、IES WHICH ARE ACQUIRED FOR AIR FORCE ORIGINAL APPLICATION, SHALL ONLY BE INTEGRALLY MOLDED CABLE ASSEMBLIES. 6. AIR FORCE USE OF ATTACHABLE PLUGS SHALL BE LIMITED TO REPLACEMENT OF ORIGINAL MOLDED ASSEMBLY PLUGS DAMAGED IN SERVICE. 7. SPLICE CRIMP BARRELS SHALL BE CRIMP TYPE. MOLD OR STAMP WIRE SIZE

19、 ON CRIMP BARREL (TABLE II). SPLICE CRIMP BARREL SHALL BE COPPER OR COPPER ALLOY. 8. TERMINAL LUGS CONNECTED TO POSITIVE “+“ AND NEGATIVE “-“ SHALL BE OF THE SIZE LISTED IN TABLE I. 9. MIL-I-23053 HEAT SHRINK INSULATION TUBING WITH ADHESIVE ON THE I.D. SHALL BE PROVIDED BY SUPPLIER OF SPLICE-ON REPL

20、ACEMENT PLUGS. THE TUBING SHALL BE USED TO INSULATE THE CRIMP BARRELS AFTER FIELD INSTALLATION. 10. INSTALLATION INSTRUCTIONS SHALL BE INCLUDED WITH EACH SPLICE-ON REPLACEMENT PLUG. FOR DESIGN FEATURE PURPOSES, THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER ACQUISITION DOCUMENTS REFERENCED HEREIN. R

21、EFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATIONS FOR BID. CERTAIN PROVISIONS OF THIS SPECIFICATION SHEET ARE THE SUBJECT OF INTERNATIONAL STANDARDIZATION AGREEMENT ASCC AIR STANDARD 12/7, 12/12, STANAG 3303 AND 3457. WHEN AMENDMENT, REVISION, OR CANCELLATION OF THIS SPECIFI

22、CATION SHEET IS PROPOSED WHICH WILL AFFECT OR VIOLATE THE INTERNATIONAL AGREEMENT CONCERNED, THE PREPARING ACTIVITY WILL TAKE APPROPRIATE RECONCILIATION ACTION THROUGH INTERNATIONAL STANDARDIZATION CHANNELS INCLUDING DEPARTMENTAL STANDARDIZATION OFFICES, IF REQUIRED. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-