SAE AS 85421 15C-2008 FITTING ELBOW 45 BEAM SEAL 3000 4000 PSI BULKHEAD MALE ENDS《外螺纹端闷头3000 4000 psi光束密封45弯头配件》.pdf

《SAE AS 85421 15C-2008 FITTING ELBOW 45 BEAM SEAL 3000 4000 PSI BULKHEAD MALE ENDS《外螺纹端闷头3000 4000 psi光束密封45弯头配件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 85421 15C-2008 FITTING ELBOW 45 BEAM SEAL 3000 4000 PSI BULKHEAD MALE ENDS《外螺纹端闷头3000 4000 psi光束密封45弯头配件》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING, ELBOW, 45 , BEAM SEAL, 3000/4000 PSI, BULKHEAD, MALE ENDS AS85421/15Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, phot

2、ocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2001-05REVISED 2008-01 REA

3、FFIRMED 2015-04 THIRD ANGLE PROJECTION CUSTODIAN: G-3 REV.C FEDERAL SUPPLY CLASS 4730AS85421/15 SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: AS85421 /4/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse of

4、thisreportis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancel

5、led. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85421/15C RATIONALE AS85421/15C HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. FIGURE 1 AEROSPACE STANDAR

6、D AS85421/15 SHEET 2 OF 3 REV. C FITTING, ELBOW, 45 , BEAM SEAL, 3000/4000 PSI, BULKHEAD, MALE ENDS TABLE 1 - DIMENSIONAL DATA MASS. LB/EA, APPROX, REF DASH NO. TUBE OD T THREAD AS8879 A B C (REF) E RAD (MIN) F RAD (REF) TI CRES -03 .188 .3750-28UNJS-3A .987 .378 .375 .084 .188 .025 .044 -04 .250 .4

7、375-24UNJS-3A 1.028 .420 .375 .084 .188 .029 .051 -05 .312 .5000-24UNJS-3A 1.046 .438 .438 .084 .219 .037 .066 -06 .375 .5625-20UNJS-3A 1.120 .471 .500 .084 .250 .046 .081 -08 .500 .7188-20UNJS-3A 1.246 .528 .562 .140 .281 .078 .138 -10 .625 .8438-18UNJS-3A 1.433 .619 .688 .140 .344 .113 .201 -12 .7

8、50 1.0000-16UNJ-3A 1.576 .685 .875 .196 .438 .154 .273 -14 .875 1.1250-16UNJ-3A 1.723 .753 1.125 .196 .563 .240 .424 -16 1.000 1.2500-14UNJS-3A 1.725 .783 1.125 .196 .563 .243 .430 -20 1.250 1.5781-14UNJS-3A 1.775 .836 1.375 .196 .688 .375 .662 -24 1.500 1.8438-14UNJS-3A 2.027 1.003 1.625 .196 .813

9、.583 1.031 SIZES -20 AND -24 WERE ORIGINALLY DESIGNATED AS SIZES -21 AND -25 ON SOME MANUFACTURERS DRAWINGS. THESE SIZES WILL NOT CONNECT WITH THE ORIGINAL -20 AND -24 FITTINGS. SEE PARAGRAPH 6.4 IN THE PROCUREMENT SPECIFICATION FOR ADDITIONAL INFORMATION. NOTES: /1/ MATERIAL: a. CODE LETTER P - TYP

10、E 17-4PH CORROSION RESISTANT STEEL PER AMS 5643. b. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY BAR PER AMS 4928 OR AMS 4965. c. CODE LETTER V - TYPE 15-5PH, CORROSION RESISTANT STEEL PER AMS 5659. 2. HEAT TREATMENT: a. MATERIAL CODE LETTER P - CONDITION H1075 PER AMS 2759/3. b. MATERIAL CODE LETTER

11、T - NONE. c. MATERIAL CODE LETTER V - AGE TO CONDITION H 1075 PER AMS-H-6875 OR AMS 2759/3. 3. FINISH: a. MATERIAL CODE LETTER P - PASSIVATE PER AMS 2700, TYPE 6 OR 7. b. MATERIAL CODE LETTER T - NONE. c. MATERIAL CODE LETTER V - PASSIVATE PER AMS 2700, TYPE 6 OR 7. /4/ PROCUREMENT SPECIFICATION: AS

12、85421 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS85421 FOR THIS STANDARD. SEE WW.EAUDITNET.COM FOR CURRENT QPL ON-LINE. /5/ I

13、DENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZES 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS” AND MATERIAL CODE LETTER, AND FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING. b. FOR SIZES 08 AND LARGER: MANU

14、FACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER, AND FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING. AEROSPACE STANDARD AS85421/15 SHEET 3 OF 3 REV. C FITTING, ELBOW, 45 , BEAM SEAL, 3000/4000 PSI, BULKHEAD, MALE ENDS 6. INVENTORIED PARTS CONFORMING TO

15、 THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION. 7. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS FOLLOWS: a. CORROSION RESISTANT STEEL AT 3000 psi. b. TITANIUM ALLOY AT 4000 psi. 8. DRY FILM LUBRICANT: APPLY DRY FILM LUBRICANT PER AS5272, TYPE I T

16、O SEALING SURFACE. OVERSPRAY IN BORE IS NOT PERMITTED. 9. TITANIUM IS NOT RECOMMENDED FOR USE IN GASEOUS OR LIQUID OXYGEN SYSTEMS. 10. INTERPRETATION OF DRAWING PER ARP4296. 11. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO B

17、E 125 in Ra. FORGED SURFACES MAY BE 250 in Ra. 12. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 13. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 14. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS + .015, ANGULAR DIMENSIONS + 0 30 15. EXAMPLE OF PART NUMBER

18、: AS85421/15 V 06 SIZE CODE, TUBE SIZE IN SIXTEENTHS IN .0625 INCREMENTS MATERIAL CODE LETTER /1/ BASIC PART NUMBER 16. IN THE EVENT OF CONFLICT BETWEEN THE TEXT OF THIS DOCUMENT AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS DOCUMENT TAKES PRECEDENCE. NOTHING IN THIS DOCUMENT, HOWEVER, SUPERSEDE

19、S APPLICABLE LAWS AND REGULATIONS UNLESS A SPECIFIC EXEMPTION HAS BEEN OBTAINED. 17. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.