SAE AS 81511 53A-2015 CONNECTOR RECEPTACLE JAM NUT MOUNT ELECTRICAL CIRCULAR HIGH DENSITY QUICK DISCONNECT ENVIRONMENT RESISTING INDIVIDUAL RELEASE CRIMP TYPE CONTACTS (CLASS A F A.pdf

《SAE AS 81511 53A-2015 CONNECTOR RECEPTACLE JAM NUT MOUNT ELECTRICAL CIRCULAR HIGH DENSITY QUICK DISCONNECT ENVIRONMENT RESISTING INDIVIDUAL RELEASE CRIMP TYPE CONTACTS (CLASS A F A.pdf》由会员分享，可在线阅读，更多相关《SAE AS 81511 53A-2015 CONNECTOR RECEPTACLE JAM NUT MOUNT ELECTRICAL CIRCULAR HIGH DENSITY QUICK DISCONNECT ENVIRONMENT RESISTING INDIVIDUAL RELEASE CRIMP TYPE CONTACTS (CLASS A F A.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD CONNECTOR, RECEPTACLE, JAM NUT MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIVIDUAL RELEASE, CRIMP TYPE CONTACTS (CLASS A, F, AND W - SERIES 4) AS81511/53Copyright 2015 SAE International All rights reserved. No part of this publication ma

2、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US

3、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2014-10REVISED 2015-04THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.A FEDERAL SUPPLY CLASS 5935AS81511/53 SHEET 1 OF 4 REV. A PROCUREMENT SPECIFICATION: AS81511SAE Technical Standards Board Rules provide

4、 that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews each

5、technicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81511/53A RATIONALE LI

6、MITED SCOPE REVISION IS REQUIRED TO CORRECT FIGURE 1, DIMENSION G AND K LABELS WERE OMITTED FROM THE FIGURE DURING THE AS CONVERSION. THE FIGURE 1 DRAWING NEEDS TO BE CORRECTED TO ADD THE DIMENSION G AND K LABELS. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONS

7、IST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. FIGURE 1 - CONNECTOR RECEPTACLE, JAM NUT MOUNT (SERIES 4) AEROSPACE STANDARD AS81511/53 SHEET 2 OF 4 REV. XA CONNECTOR, RECEPTACLE, JAM NUT MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIVIDUAL RELEASE, CR

8、IMP TYPE CONTACTS (CLASS A, F, AND W - SERIES 4) FIGURE 1 - CONNECTOR RECEPTACLE, JAM NUT MOUNT (SERIES 4) (CONTINUED) TABLE 1 - FIGURE 1 METRIC EQUIVALENTS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS INCHES MILLIMETERS .003 0.08 .035 0.89 .100 2.54 .502 12.75 .005 0.13 .067 1.70 .125 3

9、.18 .770 19.56.006 0.15 .073 1.85 .200 5.08 .778 19.76 .015 0.38 .090 2.29 .230 5.84 1.167 29.64.020 0.51 .094 2.39 .482 12.24 1.187 30.15 TABLE 2 - FIGURE 1 DIMENSIONS SHELL SIZE B D F THREAD G ACROSS FLATS K L ACROSS FLAT N THREAD P LL 8 .553 (14.05) .547 (13.89) .430 (10.92) .424 (10.77) 1/2-28UN

10、EF-2A.989 (25.12) .969 (24.61) 1.072 (27.23) 1.052 (26.72) .598 (15.19) .590 (14.99) 5/8-20UN-2A .640 (16.26) .630 (16.00) .610 (15.49) .600 (15.24)10 .678 (17.22) .672 (17.07) .555 (14.10) .549 (13.94) 5/8-28UN-2A 1.114 (28.30) 1.094 (27.79) 1.197 (30.40) 1.177 (29.90) .723 (18.36) .715 (18.16) 3/4

11、-20UNEF-2A .765 (19.43) .755 (19.18) .735 (18.67) .725 (18.42)14 .928 (23.57) .922 (23.42) .805 (20.45) .799 (20.29) 7/8-28UN-2A 1.401 (35.59) 1.381 (35.08) 1.510 (38.35) 1.490 (37.85) .973 (24.71) .965 (24.51) 1-20UNEF-2A 1.015 (25.78) 1.005 (25.53) .985 (25.02) .975 (24.77)16 1.054 (26.77) 1.048 (

12、26.62) .930 (23.63) .924 (23.47) 1-28UN-2A 1.526 (38.76) 1.506 (38.25) 1.635 (41.53) 1.615 (41.02) 1.098 (27.89) 1.090 (27.69) 1 1/8-20UN-2A 1.140 (28.96) 1.130 (28.70) 1.110 (28.19) 1.100 (27.94)18 1.178 (29.92) 1.172 (29.77) 1.055 (26.80) 1.049 (26.64) 1 1/8-28UN-2A 1.651 (41.94) 1.631 (41.43) 1.7

13、45 (44.32) 1.725 (43.82) 1.222 (31.04) 1.214 (30.84) 1 1/4-20UN-2A 1.265 (32.13) 1.255 (31.88) 1.235 (31.37) 1.225 (31.12)AEROSPACE STANDARD AS81511/53 SHEET 3 OF 4 REV. XA CONNECTOR, RECEPTACLE, JAM NUT MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIVIDUAL R

14、ELEASE, CRIMP TYPE CONTACTS (CLASS A, F, AND W - SERIES 4) TABLE 2A - FIGURE 1 DIMENSIONS SHELL SIZE AR BSC BR BSC CR BSC DR BSC PANEL O-RING EE BSC POSITION 1 2 3 4 5 6 8 128 - - - AS3582-018 40 40 40 40 40 40 10 105 140 215 265 AS3582-020 60 46 46 60 89 60 14 105 140 215 265 AS3582-024 60 46 46 60

15、 89 60 16 105 140 215 265 AS3582-026 50 50 50 50 50 50 18 105 140 215 265 AS3582-028 50 50 50 50 50 50 REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS81511. 1. DESIGN: CONNECTORS SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1 AND TABLE 2. DIMENSIONS ARE IN INC

16、HES AND APPLY AFTER PLATING. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 1 INCH = 25.4 MM. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .016 INCHES. NORMAL MATING KEYWAY POSITION SHOWN IN FIGURE 1. FOR ALTERNATE KEYWAY POSITIONS, SEE AS81511, FIGURE 4. COLOR BANDS SHALL

17、BE BLUE IN COLOR, .100 MAX. WIDTH AND SHALL BE VISIBLE WHEN MOUNTED. INSERT PROTRUSION FOR INSERTS CONTAINING SIZE 12 CONTACTS SHALL BE .070/.020. SLOTTED NUT SHALL CONFORM TO AS81511/20. 2. FOR INSERT ARRANGEMENTS, SEE AS81511, APPENDIX A. 3. PART NUMBER: THE CONNECTOR PART NUMBER WILL CONSIST OF T

18、HE LETTER M, THE BASIC SPECIFICATION NUMBER/APPLICABLE SPECIFICATION SHEET, AND THE APPLICABLE ALPHA-NUMERIC CHARACTERS ON THE CONNECTOR SHELL. THE PART NUMBER SHALL BE FORMULATED AS IN THE FOLLOWING EXAMPLE: M81511/53FD01P1. M81511/53 F D 01 P 1 BASIC PART NUMBER CLASS SHELL SIZE INSERT ARRANGEMENT

19、 CONTACT DESIGNATOR KEY POSITIONS 4. SHELL POLARIZATION: 1 THROUGH 6 KEY POSITION. 5. INSERTION AND REMOVAL TOOLS: AS81969/16 INSERTION/REMOVAL TOOL. 6. MATING CONNECTOR: THIS RECEPTACLE MATES DIRECTLY WITH AS81511/6 AND /56 PLUGS. APPLICATION NOTES: 1. AS81511 CONNECTORS AND ACCESSORIES ARE NOT REC

20、OMMENDED FOR NEW DESIGN. 2. FOR SHELL SIZES 20, 22, AND 24, USE AS81511/23 OR /49. AEROSPACE STANDARD AS81511/53 SHEET 4 OF 4 REV. XA CONNECTOR, RECEPTACLE, JAM NUT MOUNT, ELECTRICAL, CIRCULAR, HIGH DENSITY, QUICK DISCONNECT, ENVIRONMENT RESISTING, INDIVIDUAL RELEASE, CRIMP TYPE CONTACTS (CLASS A, F

21、, AND W - SERIES 4) SPECIFICATION NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHE

22、RE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.