SAE AMS 5659 H1025A-2013 Steel Corrosion-Resistant Bars Wire Forgings Rings and Extrusions 15Cr - 4 5Ni - 0 30Cb (Nb) - 3 5Cu Consumable Remelted Solution and Precipitation Heat Tr.pdf

《SAE AMS 5659 H1025A-2013 Steel Corrosion-Resistant Bars Wire Forgings Rings and Extrusions 15Cr - 4 5Ni - 0 30Cb (Nb) - 3 5Cu Consumable Remelted Solution and Precipitation Heat Tr.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 5659 H1025A-2013 Steel Corrosion-Resistant Bars Wire Forgings Rings and Extrusions 15Cr - 4 5Ni - 0 30Cb (Nb) - 3 5Cu Consumable Remelted Solution and Precipitation Heat Tr.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising ther

2、efrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this

3、publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-49

4、70 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5659/H1025A RATIONALE AMS5659/H1025A results from a limited scope ballot to c

5、orrect embedded paragraph references (3.5.3.2, 4.2.1.1). 1. SCOPE 1.1 Form This specification covers a corrosion-resistant steel product in the solution and precipitation heat treated (H1025) condition. 1.1.1 The aged product may be supplied directly by a mill or by a producer other than the mill. T

6、he latter would be accomplished by precipitation heat treatment of solution treated material previously certified to AMS5659. The entity assuming responsibility for the aging operation is designated the producer of AMS5659/H1025A. 1.2 Application These products have been used typically for parts req

7、uiring corrosion resistance and high strength up to 600 F (316 C) with good ductility and strength in the transverse direction in large section sizes, but usage is not limited to such applications (See 8.1). 1.3 Classification Melting practice classification shall be in accordance with AMS5659. AERO

8、SPACE MATERIAL SPECIFICATION AMS5659/H1025 REV. A Issued 2012-11 Revised 2013-08 Superseding AMS5659/H1025 Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 15Cr - 4.5Ni - 0.30Cb (Nb) - 3.5Cu Consumable Remelted, Solution and Precipitation Heat Treated (H1025) (Composition simi

9、lar to UNS S15500) SAE INTERNATIONAL AMS5659/H1025A Page 2 of 5 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unl

10、ess a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001,

11、 Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. AMS2750 Pyrometry AMS2759/3 Heat Treatment, Precipitation-Hardening Corrosion-Resistant and Maraging Steel Parts AMS5659 Steel, Corrosion Resistant, Bars, Wire, Forgings, Rings, and Extrusions 15Cr - 4.5Ni - 0.30C

12、b (Nb) - 3.5Cu, Consumable Remelted, Solution Heat Treated, Precipitation Hardenable AMS-H-6875 Heat Treatment of Steel Raw Materials 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall be in accordance with AMS5659. 3.2 Melting Practice Shall be in accordance with AMS5659. 3.3 Condition Shall be in acc

13、ordance with AMS5659, and the following: 3.3.1 The product shall be supplied in the precipitation hardened (H1025) heat treat condition. 3.3.2 If straightening is performed after precipitation hardening heat treatment, product shall be stress relieved by heating to 925 F (496 C) and soaking for at l

14、east one hour plus one hour additional for each inch (25 mm) of thickness or fraction thereof greater than 1 inch (25 mm). When load thermocouples are used, the soaking time shall be at least one hour. 3.4 Heat Treatment Shall be in accordance with AMS5659 and the following: 3.4.1 Precipitation Heat

15、 Treatment 3.4.1.1 Shall be in accordance with the requirements applicable to either AMS-H-6875 or AMS2759/3 at the vendors option, except acceptance testing and criteria shall be as specified in 3.5.3.1. Precipitation heat treatment furnaces shall have Type B instrumentation. 3.4.1.2 When the produ

16、ct is precipitation heat treated by an entity other than the mill producer of the AMS5659-certified product, the heat treatment source shall be accredited by a recognized industry agency for stainless steel heat treatment acceptable to the purchaser. SAE INTERNATIONAL AMS5659/H1025A Page 3 of 5 3.5

17、Properties All products shall conform to the following requirements: 3.5.1 Macrostructure Shall be in accordance with AMS5659. 3.5.2 Microstructure Shall be in accordance with AMS5659. 3.5.3 Tensile Properties Shall be in accordance with the following: 3.5.3.1 Bars Product, 12 inches (305 mm) and un

18、der in nominal diameter, thickness or for hexagons, least distance between parallel sides, and having a maximum cross-sectional area of 144 square inches (930 sq cm) shall be as shown in Table 1. Properties for larger sizes shall be as agreed upon between purchaser and vendor. Tensile testing shall

19、be performed in accordance with ASTM A 370. TABLE 1A - TENSILE PROPERTIES, INCH/POUND UNITS Condition Specimen Orientation Tensile Strength ksi Minimum Yield Strength at 0.2% Offset ksi Minimum Elongation in 2 Inches or 4D % Minimum Reduction of Area % H1025 Longitudinal Transverse 155 185 155 185 1

20、45 145 12 8 45 32 TABLE 1B - TENSILE PROPERTIES, SI UNITS Condition Specimen Orientation Tensile Strength MPa Minimum Yield Strength at 0.2% Offset MPa Minimum Elongation in 50.8mm or 4D % Minimum Reduction of Area % H1025 Longitudinal Transverse 1069 1276 1069 1276 1000 1000 12 8 45 32 3.5.3.1.1 Lo

21、ngitudinal tensile property requirements apply to specimens taken in the centerline longitudinal direction. 3.5.3.1.2 Transverse tensile property requirements apply to specimens taken approximately perpendicular to the centerline longitudinal direction. 3.5.3.1.3 Transverse tensile property requirem

22、ents apply only to bars from which a test specimen not less than 2-1/2 inches (63.5 mm) long can be taken. If the cross-sectional dimensions of square or rectangular bar permits, the transverse testing shall be of the centerline short-transverse (ST) direction; otherwise, the orientation shall be ce

23、nterline long transverse (LT). For rounds, align the samples at the centerline. 3.5.3.1.4 Bars tested in the transverse direction need not be tested in the longitudinal direction. 3.5.3.2 All other product forms: The property requirements of 3.5.3.1 shall apply. Test plans shall be as agreed upon be

24、tween vendor and purchaser. SAE INTERNATIONAL AMS5659/H1025A Page 4 of 5 3.5.3.3 When the ultimate tensile strength exceeds 185 ksi, one additional aging cycle may be performed. The set temperature for the additional aging may be higher than 1025 F (552 C), but not more than 25 F (14 C) higher. The

25、soaking time shall be not more than the original precipitation heat treatment cycle. 3.5.3.4 When the tensile properties as specified in Table 1 are not met, it is permissible to again perform solution heat treatment in accordance with AMS5659 and precipitation heat treatment to the requirements spe

26、cified in 3.4, and retest. 3.5.4 Hardness Not Applicable 3.6 Quality Shall be in accordance with AMS5659. 3.7 Tolerances Shall be in accordance with AMS5659. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor shall supply all samples for vendors tests and shall be responsib

27、le for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements. Applicable acceptance test data generated for prior certification to AMS5659 need not be repeat

28、ed for certification to AMS5659/H1025A. 4.2 Classification of Tests Shall be in accordance with AMS5659 and the following. 4.2.1 Acceptance Tests 4.2.1.1 Tensile properties (3.5.3.1) and tolerances (3.7) are acceptance tests and shall be performed on each lot. 4.2.2 Sampling and Testing Shall be in

29、accordance with AMS5659. 4.2.2.1 Resampling and Retesting Shall be in accordance with AMS5659. 4.3 Reports 4.3.1 Material provided by a producing mill The vendor of product shall furnish with each shipment a report showing the results of tests for composition and macrostructure rating of each heat a

30、nd for tensile properties of each lot, and stating that the product conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5659/H1025A, type of melting practice used, details of the precipitation heat treatment used (including, if

31、straightened, the subsequent stress relief cycle), size, and quantity. If the product size being shipped is different from the nominal metallurgically worked cross-sectional size, details of how the shipped size was extracted from the larger product shall be reported. SAE INTERNATIONAL AMS5659/H1025

32、A Page 5 of 5 4.3.2 Product from other than a producing mill using material previously certified to AMS5659 The vendor of product shall furnish with each shipment the original mill certification of the AMS5659 product and the H1025 heat treatment process certification and test report, including trac

33、eability to accreditation of the precipitation heat treat facility (See 3.4.1.2). 5. PREPARATION FOR DELIVERY Shall be in accordance with AMS5659. 6. ACKNOWLEDGMENT Shall be in accordance with AMS5659. 7. REJECTIONS Shall be in accordance with AMS5659. 8. NOTES Shall be in accordance with AMS5659 an

34、d the following: 8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision

35、 of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 When planning a manufacturing operation, users of this product should consider the surface condition that may be on the as-received product. 8.3 Procurement documents should specify not less than the following: AMS5659/H1025A Size of product desired Quantity of product desired. PREPARED BY AMS COMMITTEE “F”