NAVY MIL-V-24630-1984 VALVES CHECK IN-LINE FOR HYDRAULIC FLUID AND LUBRICATING OIL FLUID《用于液压油与润滑油液的直通单向阀》.pdf
《NAVY MIL-V-24630-1984 VALVES CHECK IN-LINE FOR HYDRAULIC FLUID AND LUBRICATING OIL FLUID《用于液压油与润滑油液的直通单向阀》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-V-24630-1984 VALVES CHECK IN-LINE FOR HYDRAULIC FLUID AND LUBRICATING OIL FLUID《用于液压油与润滑油液的直通单向阀》.pdf(20页珍藏版)》请在麦多课文档分享上搜索。
1、1 i- MIL-V-2Llb30 48 m 9777706 0275374 4 m E- ZGi -o HIL-V-24630(SH) 19 March I984 MILITARY SPECIFICATION VALVES, CHECK, IN-LINE, FOR HYDRAULIC FLUID AND LUBRICATING OIL FLUID This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by
2、 all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for in-line check valves for use in hydraulic fluid and lubricating oil fluid systems of Naval ships operating up to a maximum pressure of 3000 pounds per square inch (ib/in2).
3、1.2 Classification. In-line check valve assemblies shall be designated by standard part numbers as follows and as specified (see 6.2.1): f 24630 -I- l 1 Prefix Specification to numb er indicate. a military specification 2. APPLICABLE DOCUMENTS Ap p 1 ic a b 1 e she et numb er dimension and Dash numb
4、er specification to represent flow requirement (see specification sheets for dash number s ) 2.1 Government documents. 2.1.1 Specificatims and standards. following specifications and standards of Unless otherwise specified, the the issue listed in that issue of the Department of Defense Index of Spe
5、cifications and Standards (DoDISS) specified in the solicitation form a part of this specification to the extent specified herein. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Nava
6、l Sea Systems Command, SEA 5523, Department of the Navy, Washington, DC 20362 by using the self-addressed Standardization Document Improvement 2roposal (DU Form 1426) appearing at the end of this document or by letter. FSC 4820 THIS DOCUMENT CONTAINS -. m. PAGES Provided by IHSNot for ResaleNo repro
7、duction or networking permitted without license from IHS-,-,-MIL-V-24630 48 M 7999906 0275195 b M! SPECIFICATIONS FEDERAL QQ-N-28 1 QQ-S-7 6 3 UU-P-268 PPP-c-850 PPP-c-1120 MILITARY MIL-V- 3 MIL-S-901 MIL-G-5514 MIL-H-5606 MIL-H-6083 MIL-R-6130 MIL-R-879 1 DOD-D-1000 MIL-P-15024 - Nickel-Copper Allo
8、y Bar, Rod, Plate, Sheet, Strip, Wire, Forgings, and Structural and Spec5al Shaped Sect ions. - Steel Bars, Wire, Shapes, and Forgings, Corrosion-Resisting. - Paper, Kraft, Wrapping. - Cushioning Material, Polystyrene, Expanded, - Cushioning Material, Uncompressed Bound Fiber Resil.ient (for Packagi
9、ng -Uses). for Packaging. - Valves, Fittings, and Flanges (except for Systems - Shock Tests, H.I. (High Inpact); Shipboard Indicated Herein); Packaging of. Machinery, Equipment and Systems, Requirements for. Requirements for. Missile, and Ordnance. Preservation and Operation. - Gland Design; Packing
10、s, Hydraulic, General - Hydraulic Fluid, Petroleum Base; Aircraft, - Hydraulic Fluid, Fetroleuni Rase, for - Rubber, Cellular, Chemically Blown. - Retainer , Packing, Hydraulic, and Pneumatic, - Drawings, Engineering and Associated Lists, - Plates, Tags and Bands for Identification of Tetraf luoroet
11、hylene Kesiri. Equipment. MIL-P-15024/5 - Plates, Identification. MIL-C-15726 - Copper-Nickel Alloy, Rod, Flat Products (Flat Wire, Strip, Sheet, Rar, and Plate) and Forgings MIL-F-17111 - Fluid, Power Transmission. MIL-L-17331 - Lubricating Oil, Steam-Turbine and Gear, MIL-H-17672 - Hydraulic Fluid
12、, Petroleum, Iriliibited. MIL-H-19457 - Hydraulic Fluid, Fire-Resistant, Non-Neurotoxic. MIL-R-20092 - Rubber Sheets and Assembled and Molded Shapes, MIL-C-20159 - Copper-Nickel Alloy (70-30 and 90-10): Castings. MIL-H-22072 - Hydraulic Fluid, Catapult. MIL-P-26514 - Polyurethane Foam, Rigid or Flex
13、ible, foi: MIL-G-27617 - Grease, Aircraft and Instrument, Fuel and MIL-R-83248 - Rubber, Fluorocarbon Elastomer, High Temper- Moderate Service. Cellular, Synthetic, Operi Cell (Foamed Latex). Packaging. Oxidizer Resistant. ature, Fluid, and Compression Set Resistant. Provided by IHSNot for ResaleNo
14、reproduction or networking permitted without license from IHS-,-,-NIL-V-ZLIh30 48 37777Oh 0275176 8 MIL-V-24630 (SH) MILITARY (Continued ) MIL-H-83282 - Hydraulic Fluid, Fire Resistant, Synthetic Hydrocarbon Base, Aircraft, KAT0 Code Number H-537. tion for Hydraulic Fltiid and Lubricating Oil Fluid.
15、 Lubricating Oil Fluid. MIL-V-24630/1 - Valves, Check, In-Line, Non-Reversible Installa- MIL-V-24630/2 - Valves, Check, In-Line, for Hydraulic Fluid and STANDARDS FEDERAL, FED-STD-H28 - Screw-Thread Standards for Federal Services. MILITARY MIL-STD-167-1 - Mechanical Vibrations of Shipboard Equipment
16、 (Type I - Environmental and Type II - Internally Excited). Inspection and Repair for Machinery, Piping, arid Pressure Vessels in Ships of the United States Navy. and Acceptance Criteria of Shipbcard Equipment. Guidelines. MIL-STD-278 - Fabrication Welding and Inspection; and Casting MIL-STD-740 - A
17、irborne and Structiireborne Koie Keasurements MIL-STD-810 - Environmental Test Methods and Engineering (Copies of specifications and standards required hy contractors in connection with specific acquisition functicns should be obtained from the contracting activity or as directed by the contracting
18、officer. ) 2.2 Other publications. The following documents form a part of this specification to the extent specified herein. The issues of the documents which are indicated as DoD adopted shall be the issue listed in the current DoDISS and the supplement thereto, if applicable. APERICAK KATIONAL STA
19、NDARDS INSTITUTE (ANSL) 346.1 - Surface Texture (Surface Roiighness, Waviness and Lay). Y14.5 - Dimensioning and Tolerancing. (DOE adopted) (DoD adopted) (Application for copies should be addressed to the American Kational- Standards Institute, Inc. , 1430 Broadway, New Ycrk, NY lOGl8.) AS TM A 582
20、- Free-Machining Stainless and Heat-Resisting Steel Bars, Hot-Rolled or Cold-Fjnished. (DOE ndcptcd) (Application for coi,i.es should be addressed to ASTM, 1916 P.ace Street, Philadelphia, PA 19103.) 3 . -.- . . . . - :- -e.-*- , , . -:.:- - ._ . .- . f .- . : . Provided by IHSNot for ResaleNo repro
21、duction or networking permitted without license from IHS-,-,-MIL-V-24630 48 W 9999706 0275377 T W: MIL-V-24630 (SH) EATIONAL AEROSPACE STANDARD (NAS) Systems, 1638 - Cleanliness Requirements of Parts Used in Hydraulic (Application for copies should be addressed to the Aerospace Industries Associatio
22、n of America Inc., 1725 Desales Street, NW, Washington, DC 20036.) NATIONAL FLUID POWER ASSOCIATION (NFP (A) ) T2.6.1 - Method for Verifying the Fatigue and Static Pressure Ratings of the Pressure Containing Envelope of a Metal Fluid Power Component, Appendix Included. (Applicatjon for copies should
23、 be addressed to the National Fluid Power Association, 3333 N. Mayfair Road, Milwaukee, WI 53222.) SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) ARP 598 - The Determination of Particulate Contamination in Liquids by The Particle Count Method. (Application for copies should be addressed to the Society of Aut
24、omotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096.) (Industry association specifications and standards are generally available They are also distributed among technical groups for reference from libraries. and using Federal agencies.) 2.3 Order of precedence. In the event of a conflict
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILV246301984VALVESCHECKINLINEFORHYDRAULICFLUIDANDLUBRICATINGOILFLUID 用于 液压油 润滑油 直通 单向阀 PDF

链接地址:http://www.mydoc123.com/p-983081.html