NAVY MIL-P-85511 A-1987 PANEL ASSEMBLY TARGET BANNER AERIAL TDU-32 SERIES《TDU-32系列航空浮动目标控制板》.pdf
《NAVY MIL-P-85511 A-1987 PANEL ASSEMBLY TARGET BANNER AERIAL TDU-32 SERIES《TDU-32系列航空浮动目标控制板》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-P-85511 A-1987 PANEL ASSEMBLY TARGET BANNER AERIAL TDU-32 SERIES《TDU-32系列航空浮动目标控制板》.pdf(11页珍藏版)》请在麦多课文档分享上搜索。
1、I UIL-P-85511A 15 977990b 0206952 5 m MIL-P-8551lA(AS ) 5 JUNE 1987 . SUPERSEDING MIL-P-85511 5 March 1982 MILITARY SPECIFICATION PANEL ASSEMBLY, TARGET, BANNER, AERIAL TDU-32 SERIES This specification is approved for use within the Naval Air Systems Command, Department of the Navy, and is available
2、 for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope This specification establishes the requirements for the manufacture and acceptance of the TDU-32 series aerial banner target panel assembly, referred to herein as the panel assembly. 1.2 Classification. The pan
3、el assembly covered by this specification Iconsists of the following types: Type I. Radar non-reflective panel assembly, used on the TDU-32/B Aerial Banner Target. Type II. Radar reflective panel assembly, used on the TDU-32A/B Aerial Banner Target. Type III. Laser retroreflective panel assembly, us
4、ed on the TDU-32B/B Aerial Banner Target. - Beneficial comments (recommendations, additions, deletins) and any per- tinent data which may be of use in improving this document should be addressed to: Commanding Officer, Naval Air Engineering Center, Systems Engineering and Standardization Department
5、(SESD) Code 53, Lakehurst, New Jersey 08733-5100, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. (msc N/A FSC 1550 i nTCT RIBUTION STATEMENT A. Approved for public release; distribution is - 1 :;mited. , %
6、THIS DOCUMENT CONTAINS I I O Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- il IL - P - 5 5 L L A LFm-7 7 7 7 7 O b-020b 7 5 3 7 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and
7、standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issues of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. STA
8、NDARDS FEDERAL FED-STD-191 FED-STD-595 STANDARDS MILITARY MIL-STD-105 Textile Test Methods Colors Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 Marking for Shipment and Storage MIL-STD-794 Parts and Equipment, Procedures for Packaging and Packing of MIL-STD-831 Test Reports
9、, Preparation of I DOD-STD-2101 Classification of Characteristics 2.1.2 Drawings and publications. The following drawings and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation
10、. DRAWINGS I NAVAL AIR SYSTEMS COMMAND (Code Ident 30003) DL 966AS8000 Rev K PUBLICATIONS NAVAL AIR SYSTEMS COMI%!D (Code Ident 30003) Target, Banner, Aerial, TDU-32 Series 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-P-8551LA 15 m i777906
11、020b754 i = I O I NAVAIR 28-1OA-501 Aerial Target8 and Associated Equipment and Service Instruction (Copies of specif ications, standards, drawings, and publications required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as direc
12、ted by the contracting activity. 1 2.1.3 Order of precedence. In the event of a conflict between the text of this specification and references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations u
13、nless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.4 and 6.3). 3.1.1 First article sample. Unless otherwise specified in the contract or purchase order (see
14、6.2.11, the first article sample shall consist of three of each type of panel assemblies. The first article sample shall be manufactured using the same methods, materials, processes, and procedures proposed for production. 3.2. Design and construction. assembled in accordance with the drawings and o
15、ther documents listed on DL 966AS8000, and as specified herein. The panel assembly shall be manufactured and 3.2.1 Material characteristics and panel assembly. The material used in the fabrication of the panel assembly shall be selected by the manufacturer, and shall meet the requirements of 3.3 and
16、 3.3.1. shall be continuous with no vertical splice permitted across the width of the panel. The finished panel assembly 3.2.1.1 Type I Panel Assembly. The material used in the fabrication of the Type I panel assembly shall be transparent to radio frequency (RF) signals. 3.2.1.2 Type II Panel Assemb
17、ly. The material used in the fabrication of the Type II panel assembly shall reflect RF signals. 3.2.1.2.1 Radar reflectivity. When illuminated with horizontal or vertical polarized radar energy of 10.0 gigahertz (GHz) frequency, a one square foot sample of material from the Type II panel assembly w
18、hich has withstood three missions specified in 3.3, shall reflect no less than 90 percent of the radiated energy when radiated normal to the plane of the sample. sample shall be representative of the average condition of the panel assembly. The above 3.2.1.3 Tm. The material used in the fabrication
19、of the Type III panel assembly shall reflect RF signals and retroreflect laser radiation. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.2.1.3.1 Laser Retroflectivity. When illuminated with infrared radiation at 904 nanometers from a gallium ars
20、enide laser at normal incidence, a sample of the coated Type III panel assembly which has withstood three missions specified in 3.3, shall exhibit a retroreflectivity of not less than 1.9 (watt/steradian)/watt. The above sample shall be representative of the average condition of the tow banner. 3.2.
21、1.2.1 shall also apply to the Type III panel assembly. The radar reflectivity requirement of 3.2.1.4 Abrasion. The panel assembly, when subjected to abrasion or burning during ground-drag launched take off, shall meet the performance requirement specified herein. 3.2.1.5 Fraying and ripping. Fraying
22、 or ripping of the trailing edge of the panel assembly shall be not greater than two feet for each hour of flight. 3.2.1.6 Bullet markin&. The material used in the construction of the panel assembly, when perforated by ammunition which has been tipped with colored coating compounds, shall retain vis
23、ible traces of the compound used to provide a means of scoring projectile hits. The color coating compounds in Table I shall be used. TABLE I. Colors of coating compounds. COLOR Blue Black . Green Y ellow Purple Red Brown NATIONAL STOCK NUMBER (NSN)I _I 801 0-0 0-8 9 9 -3 17 3 8010-00-899-3174 8010-
24、00-899-3175 8010-00-899-3176 8010-00-899-3177 8010-00-899-3178 8010-00-899-31 79 3.2.1.6.1 Bullet perforation runs. The material used in the construction of the panel assembly shall not exhibit runs as a result of bullet perforation. 3.2.1.7 Visibility. In order to provide the maximum in-flight visi
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILP85511A1987PANELASSEMBLYTARGETBANNERAERIALTDU32SERIESTDU32 系列 航空 浮动 目标 控制板 PDF
链接地址:http://www.mydoc123.com/p-980851.html