NAVY MIL-P-18472 G-1989 PUMPS CENTRIFUGAL CONDENSATE FEED BOOSTER WASTE HEAT BOILER AND DISTILLING PLANT《废热锅炉和蒸馏设备的锅炉给水的浓缩物离心泵》.pdf
《NAVY MIL-P-18472 G-1989 PUMPS CENTRIFUGAL CONDENSATE FEED BOOSTER WASTE HEAT BOILER AND DISTILLING PLANT《废热锅炉和蒸馏设备的锅炉给水的浓缩物离心泵》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-P-18472 G-1989 PUMPS CENTRIFUGAL CONDENSATE FEED BOOSTER WASTE HEAT BOILER AND DISTILLING PLANT《废热锅炉和蒸馏设备的锅炉给水的浓缩物离心泵》.pdf(40页珍藏版)》请在麦多课文档分享上搜索。
1、a w e 0 a - E-35-P/ MIt-P-18472G 43 m 7779706 0273280 9 m IINCH-POUNDI MIL-P-l8472C(SH) 24 APRIL 1989 SUPERSEDING 15 December 1972 (See 6.9) MIL-P-l8472F(SHIPS) MILITARY SPECIFICATION PUMPS, CENTRIFUGAL, CONDENSATE, FEED BOOSTER, WASTE HEAT BOILER, AND DISTILLING PLANT This specification is approved
2、 for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers centrifugal pumps for condensate, boiler feed booster, waste heat boiler, and distilling plant servi
3、ces on board Naval ships. overboard and drain service. Distilling plant pumps covered herein are distillate, brine 1.2 Classification. The pumps shall be of the following classes as speci- fied (see 6.2). Class D-1 - Auxiliary condensate and distilling plant pumps - more than Class. D-2 - Main and a
4、uxiliary condensate pumps - 18-inch or less Class E - Main and auxiliary feed booster pumps. 18 - inch submergence. submergence. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and standards form a part of this document to the extent
5、 specified herein. otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). Unless Beneficial comments (reeommendations, additions, deletio
6、ns) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Naval Sea Systems Command, SFA 5523, Department of the Navy, Washington, BC 20362-5101 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at th
7、e end of this document or by letter. THIS DOCUMENT CONTAINS 40 PAGES. AMCC N/A FSC 4320 DICTRIBUTION STATEMENT A. Approved fif public release; distribution is unlimited. - -% - . / P, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-L472G 43 W 7
8、77770b 0273281 O M SPECIFICATIONS FEDERAL FF- B- 17 1 FF- B - 18 5 FF- B- 18 7 QQ-C-390 QQ - N- 2 8 1 QQ - N- 2 8 6 QQ - N - 2 8 8 QQ-S-763 TT-P-645 MILITARY MIL- S - 901 MIL- E- 917 MIL-S-1222 MIL-C-2212 MIL-P-15024 MIE-P-15024/5 MIL-E-15090 DOD-P-15328 MS 16 142 MIL-T-16420 MIL-S-16993 MIL-M-17060
9、 MIL-L-17331 MIL-M-17413 MIL-T-17523 MIL-P-17881 MIL-B-17931 MS 18229 MIL- G- 189 16 - Bearings, Ball, Annular (General Purpose). - Bearings, Roller, Cylindrical; and Bearings, Roller, Self-Aligning. - Bearing, Roller, Tapered. - Copper Alloy Castings (Including Cast Bar). - Nickel-Copper Alloy Bar,
10、 Rod, Plate, Sheet, Strip, Wire, Forgings, and Structural and Special Shaped Sections. N05500). Alloy Castings. Resisting. - Nickel-Copper-Aluminum Alloy, Wrought (UNS - Nickel-Copper Alloy and Nickel-Copper-Silicone - Steel Bars, Wire, Shapes, and Forgings, Corrosion - Primer, Paint, Zinc Chromate,
11、 Alkyd Type. - Shock Tests, H.I. (High-Impact); Shipboard Machinery, Equipment and Systems, Requirements for. (Naval Shipboard Use). Screws and Nuts. Associated Switching Devices. Equipment. - Electric Power Equipment, Basic Requirements - Studs, Bolts, Hex Cap Screws, Socket Head Cap - Controllers,
12、 Electric Motor A.C. or D.C., and - Plates, Tags and Bands for Identification of - Plates, Identification. - Enamel, Equipment, Light-Gray (Formula No. ill). - Primer (Washl, Pretreatment (Formula No. 117 for - Boss, Gasket Seal, Straight Thread Tube Fitting, - Tube, Copper-Nickel Alloy, Seamless an
13、d Welded, - Steel Castings (12 Percent Chromium). - Motors, 60 Hertz , Alternating Current , Integral- - Lubricating Oil, Steam Turbine and Gear, Moderate - Motors, Direct-Current, Integral H.P., Naval - Turbine, Steam, Auxiliary (and Reduction Gear) - Pumps, Centrifugal, Boiler Feed, (Multi-Stage),
14、 - Bearings, Ball, Annular, for Quiet Operation. - Plug for “O“ Ring Gasket. - Governors, Steam Driven Pump, Pressure Regulating, Metals) (Metric). Standard Dimensions for. (Copper Alloy Nos. 715 and 706). Horsepower, Shipboard Use. Service. Shipboard. Mechanical Drive. Naval Shipboard. 2 Provided b
15、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-L472G 43 7777906 02GFF 2GF MILITARY (Continued) MIL-C-20159 - Copper-Nickel Alloy Castings (UNS No. C96200 and MIL-P-22302 - Pumps, Centrifugal, Boiler Feed, Single Stage. MIL-S-22473 - Sealing, Locking, an
16、d Retaining Compounds: (Single-Component). MIL-C-23233 - Couplings for Propulsion Units, Auxiliary Turbines and Line Shafts Naval Shipboard. MIL-L-24131 - Lubricant, Colloidal Graphite in Isopropanol. DOD-G-24508 - Grease, High Performance, Multi-Purpose (Metric). C96400). STANDARDS FEDERAL FED-STD-
17、H28 - Screw-Thread Standards for Federal Services. FED-STD-H28/2 - Screw-Thread Standards for Federal Services Section 2 - Unified Inch Screw Threads - UN and UNR Thread Forms. MILITARY MIL-STD-167-1 - Mechanical Vibrations of Shipboard Equipment (Type I - Environmental and Type II - Internally Exci
18、ted). MIL-STD-271 MIL-STD-278 MIL-STD-438 - Schedule of Piping, Valves, Fittings, and Associ- ated Piping Components for Submarine Service. MIL-STD-740-1 - Airborne Sound Measurements and Acceptance Criteria of Shipboard Equipment. MIL-STD-740-2 - Structureborne Vibratory Acceleration Measurements a
19、nd Acceptance Criteria of Shipboard Equipment. MIL-STD-777 - Schedule of Piping, Valves, Fittings, and Associ- ated Piping Components for Naval Surface Ships. DOD-STD-1371 - Inspection Procedure for Use of Anaerobic Thread Locking Compounds with Studs. MIL-STD-1472 Systems, Equipment and Facilities.
20、 - Requirements for Nondestructive Testing Methods. - Welding and Casting Standard. - Human Engineering Design Criteriafor Military (Unless otherwise indi_cated, copies of federal and military specifications and standards are available from the Naval Publications and Forms Center (ATTN: NPODS) , 580
21、1 Tabor Avenue, Philadelphia, PA 19120-5099 .) 2.1.2 Government drawings and Dublications. The following Government drawings and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS NAVAL SEA SY
22、STEMS COMMAND (NAVSEA) NAVSHIPS B-153 - Packing and Gaskets, Application of. NAVSHIPS B-214 - Root Connections for Attaching Pipe. NAVSEA 810-1385850 - Piping, Pressure Instrument for All Services. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-
23、P-1q72G 43 7777906 0273283 q MIL-P-l8472G(SH) PUBLICATIONS NAVAL SEA SYSTEMS COMMAND (NAVSEA) NAVSEA 0900-LP-001-7000 - Fabric tion and Inspe Piping Systems. tion of Brazed (Application for copies should be addressed to the Naval Publications and Forms Center (ATTN: NPODS), 5801 Tabor Avenue, Philad
24、elphia, PA 19120-5099.) 2.2 Non-Government rmblications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless ot
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILP18472G1989PUMPSCENTRIFUGALCONDENSATEFEEDBOOSTERWASTEHEATBOILERANDDISTILLINGPLANT 锅炉 蒸馏 设备 给水

链接地址:http://www.mydoc123.com/p-980585.html