NAVY MIL-P-18080 A (2)-1989 PLASTIC SHEETS VINYL FLEXIBLE TRANSPARENT OPTICAL QUALITY《光学性能的透明的有弹性乙烯基塑料薄片》.pdf

《NAVY MIL-P-18080 A (2)-1989 PLASTIC SHEETS VINYL FLEXIBLE TRANSPARENT OPTICAL QUALITY《光学性能的透明的有弹性乙烯基塑料薄片》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-P-18080 A (2)-1989 PLASTIC SHEETS VINYL FLEXIBLE TRANSPARENT OPTICAL QUALITY《光学性能的透明的有弹性乙烯基塑料薄片》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、- MIL-P-1808OA (2) 93 779990b 0337203 I /INCH-POUNDI MIL-P-I8080A(SHIPS) AMENDMENT 2 7 Amil 1989 SUPERSEDING AMENDMENT 1 10 January 1967 MILITARY SPECIFICATION PLASTIC SHEETS, VINYL, FLEXIBLE, TRANSPARENT, OPTICAL QUALITY This amendment forms a part of MIL-P-l8080A(SHIPS), dated 2 March 1956, and is

2、 approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. * 2.1, 2.1: ! * 2.1, Tables“. PAGE 1 MIL-T-19102 : Delete “Gas“ and substitute “Protective“. Delete : “NAVY DEPARTMENT General Specificat

3、ions for Inspection of Material.“ MIL-STD-105: Delete “Inspection Table“ and substitute “Procedures and * 2.2: “2.2 PAGE 2 Delete and substitute: Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues o

4、f the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation. ., AMSC N/A FSC 9330 DISTRIBUTION STATEMENT A. Approved

5、 for public release; distribution is unlimited. 1 of s 7- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-LOOA (2) 73 M 7977706 OLL7204 3 MIL-P-l808OA(SHIPS) AMENDMENT 2 AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 412 - Standard Test Me

6、thods for Rubber Properties in Tension. D 746 - Standard Test Method for Brittleness Temperature of D 792 - Standard Test Methods for Specific Gravity (Relative (DoD adopted) Plastics and Elastomers by Impact. (DoD adopted) Density) and Density of Plastics by Displacement. (DoD adopted) of Transpare

7、nt Plastics. (DoD adopted) (DoD adopted) D 1003 - Standard Test Method for Haze and Luminous Transmittance D 3951 - Standard Practice for Commercial Packaging. (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (N

8、on-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.)I * Add as new paragraph 2.3: “2.3 Order of precedence. In the event o

9、f a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. PAGE 4 4.1 through 4.3: Delete and substitute: * “4

10、.1 ResDonsibilitv for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contract

11、or may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Govern- ment reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necess

12、ary to ensure supplies and services conform to prescribed requirements. 4.1.1 ResDonsibilitv for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program.

13、absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies The 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- NIL-P-LBOBOA (2) 93 = 9999906 0117205

14、5 MIL-P-l808OA(SHIPS) AMENDMENT 2 submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of the manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of

15、known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.2 Sampling for sualitv conformance inspection. Sampling for quality conformance inspection shall be performed in accordance with the provisions set forth in MIL-STD-105, except whe

16、re otherwise indicated. For purposes of sampling, an inspection lot for inspection and tests shall consist of all material of the same type, machine run and thickness range submitted for delivery at one time. 4.2.1 Inspection of materials and components. In accordance with 4.1 above, the supplier is

17、 responsible for insuring that materials and components used were manufactured, tested and inspected in accordance with the requirements of referenced subsidiary specifications and standards to the extent specified, or, if none, in accordance with this specification. In the event of conflict, this s

18、pecification shall govern. 4.2.2 InsDection of the end item. 4.2.2.1 Examination of the end item. Examination of the end item shall be made in accordance with the classification of defects, inspection levels and . acceptable quality levels (AQLc) set forth below. The lot size, for purpose of determi

19、ning the sample size in accordance with MIL-STD-105, shall be expressed in units of plastic sheets for examination in 4.2.2.1.1, 4.2.2.1.2 and in units of shipping containers for examination in 4.2.2.1.3. 4.2.2.1.1 Examination of the end item for defects in appearance and workmanchip. specified type

20、 plastic material. The sample unit for this examination shall be one sheet of the Examine Defects Appearance and workmanship Not uniform in transparency. Any blisters, bubbles, wrinkles, creases, cuts, tears, holes, dents, heat marks, or graininess which will affect serviceability. Any-scratches, di

21、rt, imbedded particles or other defects which will reduce visibility or affect appearance. Finish Color Not finished to a polished or smooth finish. Not colorless and transparent. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-3OOA (2) 73 97

22、97706 0337206 7 W MIL-P-l808OA(SHIPS) AMENDMENT 2 4.2.2.1.2 Examination of the end item for dimensional defects. The sample unit for this examination shall be one sheet of the specified type plastic material. Examine Defects Length and width Th ic kne s s Varies by more than minus O plus 1/4 inch fr

23、om size specified. Varies by more than plus or minus the tolerance specified (see table 11). 4.2.2.1.3 Examination of the preparation for delivery. An examination shall be made to determine that packaging, packing and markings comply with the requirements of section 5. The sample unit for this exami

24、nation shall be one shipping container, fully packed, selected just prior to the closing operation. Shipping containers fully prepared for delivery shall be examined for closure defects. Examine Defects Packaging Packing Count Not level specified, not in accordance with contract requirements. Packag

25、ing material not as specified. Paper interleaves missing, not extending over full area between sheets, or not as specified. Not level specified, not in accordance with contract requirements. Any nonconforming component, component missing, damaged or otherwise defective, affecting serviceability. Con

26、tainer not as specified, closures not accomplished by specified or required methods or materials. Inadequate application of components such as: incomplete closure of case liners, container flaps, loose or inadequate strapping, bulged or distorted containers. Less than specified or indicated quantity

27、 of sheets per container. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-LBOBOA (2) 73 7797906 OLL7207 7 Examine Weight Markings MIL-P-l8080A(SHIPS) AMENDMENT 2 Defects Gross or net weight exceeds specified requirements. Exterior markings om

28、itted, illegible, incorrect, incomplete or not in accordance with dontract requirements. Precautionary markings missing or not as specified. 4.2.3 Inspection levels and acceptable quality levels (AQLs) for examina- The inspection levels for determining the sample size and the acceptable tion. qualit

29、y levels (AQLs) expressed in defects per 100 units, shall be as follows: Examination paragraDh InsDection level AQL - 4.2.2.1.1 4.2.2.1.2 4.2.2.1.3 I s-3 s-2 2.5 2.5 4.0 4.3 Testing of the end item. The end item shall be tested for the applicable characteristics as indicated in table III, on each lo

30、t presented for examination. The sample unit shall be one sheet. The inspection level for determining the sample size shall be S-1, except that no less than three sample units shall be randomly selected throughout the lot. level (AQL) shall be 6.5 expressed in defects per 100 units. The acceptable q

31、uality 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-br G .rl u rn al U . Packing shall be level A, B, or Commercial, as specified (see 6.2) .I1 .k 5.2.3: Delete and substitute: “5.2.3 Commercial. Plastic sheets preserved as specified in 5.1 shal

32、l be packed in accordance with ASTM D 3951.“ * 5.3, line 2: Delete all after “order,“ and substitute: “level A and B exterior shipping containers shall be marked in accordance with MIL-STD-129, commercial exterior containers in accordance with ASTM D 3951, and shall include barcode markings on all e

33、xterior containers.“ * 6.2: Delete and substitute: “(c) Level or commercial preservation and packing required (see 5.1 and 5.2) .I1 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I. MIL-P-LOOA (2) 73 W 7777906 OLL72LO 7 W MIL-P-l8080A(SHIPS) AMEND

34、MENT 2 PAGE 8 Patent notice: Delete. Custodian: Delete. The margins of this amendment are marked with an asterisk or vertical lines to indicate where changes (additions, modifications, corrections, deletions) from the previous amendment were made. This was done as a convenience only and the Governme

35、nt assumes no liability whatsoever for any inaccuracies in these nota- tions. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Preparing activity: Navy - SH (Project 9330-NB16) 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-