NAVY MIL-M-19417 D-1992 MASK ASSEMBLIES OXYGEN AND SMOKE FULL FACE《全面氧气和烟雾的面具装配》.pdf
《NAVY MIL-M-19417 D-1992 MASK ASSEMBLIES OXYGEN AND SMOKE FULL FACE《全面氧气和烟雾的面具装配》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-M-19417 D-1992 MASK ASSEMBLIES OXYGEN AND SMOKE FULL FACE《全面氧气和烟雾的面具装配》.pdf(22页珍藏版)》请在麦多课文档分享上搜索。
1、NIL-M-II94L7D 16 m 9999906 1210219 TOO = 29 September 1992 SUPERS ED I NG MIL-M-19417C 27 December 1985 MILITARY SPECIFICATION MASK ASSEMBLIES, OXYGEN AND SMOKE, FULL FACE This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This sp
2、ecification covers three types of full face, oxygen and smoke mask assemblies. 1.2 Classification. Mask assemblies shall be of the following types, as specified (see 6.2b): Type I - Mask, hose assembly (MS90339-3), and connector (MS22016). Type II - Mask, hose assembly (MS90339-21, and connector (US
3、AF Drawing 55B3509). Type III - Mask, hose assembly (NAVAIR Drawing 3072AS100 and connector MS22016). 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and * standards form a part of this specification to the extent specified herein. U
4、nless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (See 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinen
5、t data which may be of use in improving this document should be addressed to: Commanding Officer, Naval Air Warfare Center Aircraft Division Lakehurst, Code SR3, Lakehurst, NJ 08733-5100, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document
6、or by letter. AMSC NIA FSC 1660 DISTRIBUTION STATEMENT A. Approved for pub1 ic release; distribution is un1 imi ted. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-lt9417D Lb W 9999906 L2L0220 722 MIL-M-19417D SPEC1 FICATIONS FEDERAL UU-P-268
7、uu-P- 55 3 PPP- 8-60 1 PPP-B-6 36 PPP-T-60 PPP-T-76 MI LI TARY MIL-P-116 DOO-D- 1 O00 MI L-P-5425 MIL-C-19246 MIL-A-2359512 MIL-M-26542/6 MIL-M-26542/7 MIL-0-27210 STANDARDS FEDERAL FED-STD-595 FED-STO-601 MILITARY MIL-STD-105 MIL-STO-1 29 MI L-STO- 1 30 Paper, Kraft, Wrapping Paper, Wrappi ng , Ti
8、ssue Boxes, Wood, Cleated-plywood Box, Shipping, Fiberboard Tape, Packaging, Waterproof Tape, Pressure Sensitive Adhesive, PackagingIPaper (for Carton Sealing) Preservation, Methods of Drawings, Engineering and Associated List Plastic, Sheet, Acrylic, Heat Resistant Connector, Oxygen Mask Hose, Type
9、 MC-3A Amp1 i fi er, Audio Frequency AM-4326BIA Microphone, M-l03/AIC Mi crophone, M-94B/A Oxygen, Aviators Breathing, Liquid and Gas Col ors Rubber, Sampl i ng and Test i ng Sampl i ng Procedures and Tab1 es for Inspection By Attributes Marking for Shipment and Storage Identification Marking of U.S
10、. Military Property 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c MIL-M-L94L7D Lb D 9999906 1210221 bb9 D MIL-M-19417D MIL-STD-2073-1 - DOD Materiel Procedures For Development and Application of Packaging Requirements MS22016 - Connector, Oxyge
11、n Mask Hose, Type MC-3A MS90339 - Hose Assembly, Oxygen Mask to Connector MS90340 - Insert, Instal lation and Detai 1, Fu1 1 Face oxygen and Smoke Mask (Unless otherwise indicated, copies of federal and military specifications, standards and handbooks are available from the Standardization Documents
12、 Order Desk, Bldg 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 Other Government documents and drawings. The following other * Government documents and drawings form a part of this specification to the extent specified herein. Unless otherwise specified, the issues are those cited in t
13、he solicitation. DRAW I NGS NAVAL AIR SYSTEMS COMMAND 307 2AS 1 O0 - Hose and Communication Assembly USAF 5583509 - Connector, Demand Mask to Regulator Tube Internal, Assembly of (Copies of drawings required by contractors in connection with specific acquisition functions should be obtained from the
14、 contracting activity or as directed by the contracting officer.) 2.2 Non-Government publications. The following document(s1 form a part * of this document to the extent sDecified herein. Unless otherwise sDecified. the issues of the documents which are DoD adopted are those listed in the issue of t
15、he DoDISS cited in the solicitation. of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). Unless otherwise specified, the issues AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM D 256 - Impact Resistance of Plastics and Electrical Insulatin
16、g Materials ASTM D 542 - Index of Refraction of Transparent Organic Plastics ASTM D 543 - Resistance of Plastics to Chemical Reagents 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-M-4i44i7D 4ib 0b L2LO222 5T5 1 ASTM D 570 ASTM D 635 ASTM D 63
17、8 ASTM D 648 ACTM D 695 ASTM D 790 ASTM D 1003 ASTM D 1044 ASTM D 1149 ASTM E 831 ASTM F 791 Water Absorption of Plastics Rate of Burning and/or Extent and Time of Burning of Self-Supporting Plastics in a Horizontal Position Tensile Properties of Plastics Deflection Temperature of Plastics Under Fle
18、xural Load Compressive Properties of Rigid Plastics Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials Haze and Luminous Transmittance of Transparent Plastics Resi stance of Transparent Plastics to Surface Abrasion Rubber Deterioration - Surface Ozone Cra
19、cking in a chamber (Flat specimens) Linear Thermal Expansion of Solid Materials By Thermomechanical Analysis Stress Crazing of Transparent Plastics (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Non-Governmen
20、t standards and other publications are normally available from organizations that prepare and distribute the documents. may be available in or through libraries or other informational services.) These documents also * 2.3 Order of precedence. In the event of a conflict between the text of this docum
21、ent and the references cited herein (except for related associated detail specifications, specification sheets, or MS standards), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3
22、. REQUIREMENTS 3.1 Qualification. The mask assemblies furnished under this specification shall be products which are authorized by the qualifying activity for listing on the applicable Qualified Products List at the time of award of contract (see 4.3 and 6.3). In addition, the retention of the quali
23、fication for the mask assemblies on the applicable qualified products list shall be dependent on periodic verification of continued compliance with the requirements of this spcification (see 4.3 and 4.3.2). * 3.2 First article. When specified (see 6.2f1, a sample shall be subjected to first article
24、inspection (see 6.4) in accordance with 4.4. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L NIL-M-L9417D Lb m 99999Ob 1210223 431 m 3.3 Materials. Materials shall conform to applicable specifications and shall be as specified herein and on appli
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILM19417D1992MASKASSEMBLIESOXYGENANDSMOKEFULLFACE 全面 氧气 烟雾 面具 装配 PDF

链接地址:http://www.mydoc123.com/p-980295.html