NAVY MIL-I-6115 A (4)-1999 INSTRUMENT SYSTEMS PITOT TUBE AND FLUSH STATIC PORT OPERATED INSTALLATION OF《皮托管和冲水静态港口经营仪表系统安装指南》.pdf

《NAVY MIL-I-6115 A (4)-1999 INSTRUMENT SYSTEMS PITOT TUBE AND FLUSH STATIC PORT OPERATED INSTALLATION OF《皮托管和冲水静态港口经营仪表系统安装指南》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-I-6115 A (4)-1999 INSTRUMENT SYSTEMS PITOT TUBE AND FLUSH STATIC PORT OPERATED INSTALLATION OF《皮托管和冲水静态港口经营仪表系统安装指南》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUND MIL-1-6 1 1 5A AMENDMENT 4 15 December 1999 SUPERSEDING AMENDMENT 3 3 1 December 1960 MILITARY SPECIFICATION INSTRUMENT SYSTEMS, PITOT TUBE AND FLUSH STATIC PORT OPERATED, INSTALLATION OF This amendment forms a part of MIL-1-6 1 15A, dated 29 March 195 1 , and is approved for use by all D

2、epartments and Agencies of the Department of Defense. PAGE 1 Preamble: Delete and substitute the following: “This specification has been approved by the Department of Defense and is mandatory for use by the Departments of the Army, the Navy and the Air Force.” Section 2: Delete and substitute: “2. A

3、PPLICABLE DOCUMENTS 2.1 The following documents, of the issue in effect on date of invitation for bids, form a part of this specification to the extent specified herein: SPECIFICATIONS FEDERAL WW-T-787 Tube, Aluminum Alloy, Round, Square, Rectangular, and Other Shapes, Drawn, Seamless, 5052 MILITARY

4、 * TT-P- 1757 Primer Coating, Alkyd Base, One Component MIL-A-8625 Anodic Coatings, for Aluminum and Aluminum Alloys AMSC N/A 1 of4 FSC 66 1 O DISTRTBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted withou

5、t license from IHS-,-,-MIL-1-6 1 15A AMENDMENT 4 STANDARDS MILITARY MS33586 Metals, Definition of Dissimilar MS33656 Fitting End, Standard Dimensions for Flared Tube Connection and Gasket Seal AIR FORCE-NAVY AERONAUTICAL AN 929 AN581 1 AN5812 AN5813 Tube, Pitot, Electrically Heated AN6270 AND 103 75

6、 AND10410 Cap Assembly, Pressure Seal Flared Tube Fitting Tube, Pitot, Electrically Heated, “L” Shaped, Inverted Tube, Pitot, Electrically Heated, “L” Shaped Hose Assembly - Detachable Swivel Fitting, Low Pressure Colors - Fluid Line Identification Pitot-static and Pitot Tube - Wiring Diagram for PU

7、BLICATIONS NAVAL AIR MATERIAL CENTER Report No. NAES - and Airspeed Installation INSTR. 1-44 Dual Sighting Stand and Other Methods of Calibrating Altimeter (Copies of this publication may be obtained from the Engineering Division, Documentation Branch, Bureau of Naval Weapons, Navy Department, Washi

8、ngton, DC.) (Copies of specifications, standards, drawings, and publications required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Other publications. The following document forms a par

9、t of this specification to the extent specified herein. Unless otherwise indicated, the issue in effect on date of invitation for bids shall apply: NATIONAL AERONAUTICS AND SPACE ADMINISTRATION Report 9 19 Accuracy of Airspeed Measurements and Flight Calibration Procedures (Copies of this report may

10、 be obtained from the National Aeronautics and Space Administration, 1520 H Street, NW, Washington, DC.)” 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-9999906 2112458 31b m MIL-1-6 1 1 5A AMENDMENT 4 PAGE 2 * Lines 4 and 5: Delete “zinc-chromate

11、 primer conforming to Specification MIL-P-6889” and substitute “alkyd primer conforming to TT-P- 1757.” 3.1.1.1 line 2: Delete “Drawing AND10398” and substitute “MS33586.” 3.1.2, line 4: Delete “ANA Bulletin No. 143” and substitute “procedures established by the procuring activity or as specified in

12、 the contract or order.” PAGE 3 Add the following new paragraph: 3.1.2.2 AN or MS straight threaded fittings only shall be used and shall be connected in accordance with the applicable standards listed in section 2.” 3.2.1: Line 2, delete “Drawings” and substitute “Standards.” PAGE 8 3.2.6.7.1, line

13、 2: Delete “AN-QQ-A-696” and substitute “MIL-A-8625. 3.2.7.1, line 4: Delete “AN-QQ-A-696” and substitute “MIL-A-8625.” PAGE 9 Figure 4: In note above figure title, delete “DRAWING AND 10056” and substitute “MS3 3656.” PAGE 10 3.2.7.3, line 2: Delete “Drawing” and substitute “Standard” and add the f

14、ollowing at the end of the paragraph: “The color coding shall speciSl distinctly which line is pitot pressure and which line is static pressure. The marking tape shall be within 3 inches of the terminal fitting.” 3.2.9, lines 2,4, and 7: Delete “Drawing” and substitute “Standard.” 3.2.1 1, lines 3 a

15、nd 4: Delete “Drawing AND10056” and substitute “Standard MS33656.” 3.2.15, line 2: Delete “Drawing” and substitute “Standard.” PAGE 11 Section 4: Delete “4. SAMPLING, INSPECTION, AND TEST PROCEDURES” and substitute the following heading and new paragraph: 3 Provided by IHSNot for ResaleNo reproducti

16、on or networking permitted without license from IHS-,-,-“4. Q W 9999906 2112459 252 MIL-1-6 1 15A AMENDMENT 4 IALITY ASSURANCE PROVISIONS 4.1 Insuection responsibility. The supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified,

17、the supplier may utilize his own or any other inspection facilities and services acceptable to the Government. Inspection records of the examination and tests shall be kept complete and available to the Government as specified in the contract or order. The Government reserves the right to perform an

18、y of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements.” 4.1 : Delete the last three sentences. PAGE 12 * indicates 9.10 inch Hg differential pressure.” 4.2.4.3, line 3: Delete “or a mercury m

19、anometer.” Line 7: Delete “or the manometer 4.2.6.1, lines 2 and 3: Delete “NACA Technical Note 1605” and substitute “National Aeronautics and Space Administration Report 9 19.” NOTE: The margins of this amendment are marked with asterisks to indicate where changes from the previous amendment were m

20、ade. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. custodians: Navy - AS Army - AV Preparing activity: Navy - AS (Project 66 10-0603) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-