NAVY MIL-H-775 E-1987 HOSE HOSE ASSEMBLIES RUBBER PLASTIC FABRIC OR METAL (INCLUDING TUBING) AND ASSOCIATED HARDWARE PACKAGING OF《橡胶 塑料 织物或金属(包括管道敷设)和相关硬件的管道组装》.pdf

《NAVY MIL-H-775 E-1987 HOSE HOSE ASSEMBLIES RUBBER PLASTIC FABRIC OR METAL (INCLUDING TUBING) AND ASSOCIATED HARDWARE PACKAGING OF《橡胶 塑料 织物或金属(包括管道敷设)和相关硬件的管道组装》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-H-775 E-1987 HOSE HOSE ASSEMBLIES RUBBER PLASTIC FABRIC OR METAL (INCLUDING TUBING) AND ASSOCIATED HARDWARE PACKAGING OF《橡胶 塑料 织物或金属(包括管道敷设)和相关硬件的管道组装》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-H-775E PA 7777706 0277268 5 I INCH-POUND . PiIL-H-775E 19 October 1987 SUPERSEDING MIL-P-775D 19 November 1973 (See 6.8) NILITARY SPECIFICATION HOSE, HOSE ASSEMBLIES; RUBBER, PLASTIC, FABRIC, OR METAL (INCLUDING TUBING) AND ASSOCIATED HARDWARE: PACKAGING OF This specification is approved for use

2、 by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the packaging for shipment, stowage, and storage of various types of hose, hose assemblies, tubing, and associated hardware. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specificat

3、ions and standards, The following specifications and standards form a part of this specification to the extent spe-cified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) a

4、nd supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL L-P-378 QQ-S-781 PPP-F-320 PPP-B-566 PPP-B-576 PPF-B-585 PPP-B-591 PPP=B-601 PFP-B-621 - Plastic Sheet and Strip, Thin Gauge, Polyolefin. - Strapping, Steel, and Seals. - Fiberboard, Corrugated and Solid, Sheet Stock - Boxes, F

5、olding, Paperboard. - Boxes, Wood, Cleated, Veneer, Paper Overlaid. - Boxes, Wood, Wirebound. - Boxes, Shipping, Fiberboard, Wood-Cleated. - Boxes, Wood, Cleated-Plywood. - Boxes, Wood, Nailed and Lock-Corner. (Container Grade), and Cut Shapes Beneficial comments (recommendations, additions deletion

6、s) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Naval Sea Systems Command, SEA 5523, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the

7、 end of this document or by letter. AMSC N/A AREA PACK DISTRIBUTION STATEMENT A Approved for public release; distribution unlimited THIS DOCUMENT CONTAINS 20“ PAGES, ,- 4, “ - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-” MIL-H-775E PA = 9999906

8、0279269 7 PlIL-H-775E FEDERAL (Continued) PPP-B-636 - Boxes, Shipping, Fiberboard. PPP-B-640 - Boxes, Fiberboard, Corrugated, Triple-Wall. PPP-B-665 Boxes: Paperboard, Fletal Edged and Components. PPP-B-676 - Boxes, Setup. PPP-c-735 - Cushioning Material, (Flexible Cellular, Plastic Film) for Packag

9、ing Applications. PPP-L-1607 - Lagging, Wood, Wirebound. MILITARY MIL-V-3 MIL-P-116 MIL-B-121 MIL-P-4861 MIL-C-5501 MIL-1-8574 MIL-L- 19 i40 MIL-B-22019 MIL-B-22020 MIL-B-22191 MIL-A-25175 MIL-C-52211 - Valves, Fittings, and Flanges (Except for Systems - Preservation, Methods of. - Barrier Material,

10、 Greaseproofed, - Packing, Preformed, Rubber, Packing; Packaging of. - Cap and Plugs, Protective, Dust and Moisture - Inhibitors, Corrosion, Volatile, Utilization of. - Lumber and Plywood, Fire-Retardant Treated. - Barrier Materials, Transparent, Flexible, - Bags, Transparent, Flexible, Sealable, Vo

11、latile - Barrier Materials, Transparent, Flexible, Heat- - Air Transport, Nontactical, Packing for. - Components and Assemblies for Industrial Gas Indicated Herein); Packaging of. Waterproofed, Flexible. Seal, General Specification for. Sealable, Volatile Corrosion Inhibitor Treated. Corrosion Inhib

12、itor Treated. Sealable. Production, Storage and Transport Equipment, Packaging of. STANDARDS MILITARY MIL-STD-129 - Marking for Shipment and Storage. MIL-STD-147 - Palletized Unit Loads, MIL-STD-758 - Packaging Procedures for Submarine Repair Parts. MIL-STD-1186 - Cushioning, Anchoring, Bracing, Blo

13、cking, and MIL-STD-1330 - Cleaning and Testing of Shipboard Oxygen, Waterproofing; with Appropriate Test Methods. Nitrogen and Hydrogen Gas Piping Systems. (Copies of specifications and standards required by contractors in connection with specific acquisition functions should be obtained from the co

14、ntracting activity or as directed by the contracting activity.) 2.2 Other publications. The following documents form a part of this mecification to the extent specified herein. Unless otherwise specified, the ssues of the documents which- are DoD adopted shall be those listed in the issue of the DoD

15、ISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS shall be the issue of the nongovernment documents which is current on the date of the solicitation. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

16、rom IHS-,-,-MIL-H-775E PA = 7777906 0277270 3 MIL-H-775E AMERICAN SOCIElY FOR TESTING AND MATERIALS (ASTM) D 996 - Standard Terminology to Packaging and Distribution D 3951 - Standard Practice for Commercial Packaging. (DoD adopted) Environments. (Application for copies should be addressed to the Am

17、erican Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents, These documents also may be available in or through libraries or other i

18、nformational services,) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein (except for associated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in thi

19、s specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Definitions or explanation of packaging terms. Definitions or explanation of packaging terms applicable to this specification shall be as stated in the applica

20、ble referenced documents, specification, and 6.4. For definitions or explanation of Packaging terms not specified therein, ASTM D 996 shall apply. 3.2 Materials. Packaging material shall be as specified herein and in the applicable referenced specifications. 3.2.1 Recovered materials. Unless otherwi

21、se specified herein, all equipment, material, and articles incorporated in the products covered by this specification shall be new and may be fabricated using materials produced from recovered materials to the maximum extent practicable without jeopardizing the intended use. The term “recovered mate

22、rials“ means materials- which have been collected or recovered from solid waste and reprocessed to become a source of raw materials, as opposed to virgin raw materials. None of the above shall be interpreted to mean that the use of used or rebuilt products is allowed under this specification unless

23、otherwise specifically specified. 3.2.2 New materials. The use of newly developed packaging materials or procedures are encouraged and recommended and will be permitted under the conditions specified herein, provided they .are equal to or better than the specified materials or procedures. 3 Provided

24、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-775E PA W 9999906 0279271 5 W NIL-H-775E 3.2.2.1 Certification of new materials. When specified in the contract or order, a certificate of compliance shall be prepared, when materials or procedures other

25、than those specified herein are used. (see 6.2.2). 3.2.3 Asbestos (see 6.3). 3,2.3,1 Packaging materials. Asbestos or material and items containing asbestos shall not be used in the packaging of material covered by this specification (see 6.3). 3.2.3.2 Packaged asbestos material. All asbestos and se

26、parately packaged components containing asbestos that is predominately distributed throughout the item, shall be packaged in sealed, dustproof and siftproof packages. Flexible packages shall be heat sealed. Packages shall be marked as specified (see 3.4.3). 3.2.3.3 Talc and talcum. When specified in

27、 the contract or order, a certificate of compliance stating the dusting materials used in the packaging process (for example, talc and talcum) are asbestos free, shall be prepared (see 6.2.2). 3.2.4 Cushioning and wrapping materials (see 3.4.2.2 and 6.7). The use of excelsior, newspaper, shredded pa

28、per (all types) and similar hydroscopic or non-neutral materials and all types of loose fill materials (for applications such as cushioning, fill, stuffing, and dunnage) shall be prohibited. 3.2.5 Fire retardant treatment and materials (see 6.7). For Navy acquisitions, the following applies: (a) Nav

29、y fire-retardant requirements. (1) Lumber and plywood. Unless otherwise specified (see 6.2.1), all lumber and plywood including laminated veneer material used in shipping container and pallet construction, members, blocking, bracing, and reinforcing shall be fire-retardant treated material conformin

30、g to MIL-L-19140 as follows: Level A and B - Type II - weather resistant. Level C - Type I: - non-weather resistant. Category I - general use. Category I - general use. (2) Fiberboard. Unless otherwise specified (see 6.2.1), fiber- board used in the construction of class-domestic, non- weather resis

31、tant fiberboard, and cleated fiberboard boxes shall meet the flame spread index and specific optic density requirements of PPP-F-320. 3,3 Data and drawings. When specified in the contract or order, complete descriptive packaging details on drawings of the sample pack shall be prepared (see 6.2.2). 4

32、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-H-775E PA 777770b 0277272 7 m 3.3.1 Preservation and packing data. When specified in the contract or order, coded and in-the-clear preservation and packing data shall be prepared (see 6.2.2). 3.4

33、 Levels of protection (see 6.4.1). 3.4.1 Preservation. Preservation (unit protection) shall be level A, C or commercial as specified (see 6.2.1). 3.4.1.1 Level A. Unless otherwise specified herein, cleaning processes, drying procedures, preservative application, and methods of preservation (unit pro

34、tection) shall be in accordance with MIL-P-116 and table I herein. Require- ments in table I are assigned by category. Nethods are assigned on the basis of the type of unit protection most commonly required for a specific commodity. Unless otherwise specified (see 6.2.1), selection of the submethod,

35、 where appli- cable, under a particular method shall be at the option of the contractor. Oxygen system hose and hose hardware shall be processed as specified in 3.4.1.1.1.3.5. TABLE I. Hose hardware (see 3.4.1.1.2). Type of fittings, hose nozzle, or strainer Adapter, hose: Ferrous Nonferrous Hose, b

36、rass, with chain Cap : and spanner lugs Clamp: Hose Connect ion : Hose Couplings: Aluminum, anodized with non-metallic gaskets and lubricant to threads Nonferrous Ejector : Steam Fil ler : Barrel, automatic, with 6-foot hose and female coup 1 ing . Gland : Acetylene, with nut 1/4 Hose connection, we

37、lding, Oxygen, with nut, 1/4 to to 5/16 inch 5/16 inch hose 5/16 inch Process of cleaning c-3 c- 1 c-1 c-3 c-3 c-1 c-1 c-3 c-1 c-3 c-3 -“- Method of preservation I III III I I III III I III IC IC “ Special requirements See 3.4.1.1.2.4 See 3.4.1.1.2.4 See 3.4,1.1.2.4 See 3.4.1.1.2.4 Without preservat

38、ive One gland with See 3.4.1.1.1.3.5 nut per unit pack 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-“ MIL-H-775E PA 777770b 0277273 7 - MIL-H-775E TABLE I. Hose hardware (see 3.4.1.1.2). - Continued Type of fittings, hose nozzle, or strainer Inj

39、ector: Steam Joint: Diving-apparatus air-hose union: Double female and male Nipple: Nozzle: Hose, air Fixed, preset (AFFF) Hose, steam injector Hose Preformed Nut : Packing : Play pip: Stub, shut-off Ring : Splicer: Hose expansion, brass Hose, air Strainer Tip Valve : Brass Washer: Hose, rubber Proc

40、ess of cleaning c-3 “ c-3 c-1 c-3 c-3 “ c-3 c-1 c-3 c-3 c-3 c-1 Nethod of preservation I “ I III I I “ I III I I I -“- III Special requirements See 3.4.1.1.2.5 See 3.4.1.1.1.3.5 See 3.4.1.1.2.5 Nozzles with mating surfaces shall be completely assem- bled prior to unit pack. See 3.4.1.1.2.5 See 3.4.1

41、.1.2.5 See MIL-P-4861 Cushioned or blocked in fiberboard box see 3.4.1.1.2.5 See 3.4.1.1.2.5 See 3.4.1.1.2.5 See 3.4.1.1.2.5 See MIL-V-3 See 3.2.3 and 3.4.1.1.2.3 3.4.1.1.1 Hose or hose assemblies. Unless otherwise specified (see 6.2.1), hose or hose assemblies and tubing shall be cleaned in accorda

42、nce with process C-1. Preservation method III shall apply to hose and method I to hose assemblies. Oxygen system hose and hose assemblies shall be cleaned as specified in 3.4.1.1.1.3.5. 3.4.1.1.1.1 Hose hardware. Attached hose hardware shall be cleaned in accordance with table I and coated with a pr

43、eservative (see 3.4.1.1.1.2). Hose hardware when furnished loose shall be processed as specified in table I with preservative selection as specified in 3.4.1.1.1.2. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-775E PA W 9797906 0277279 O N

44、IL-H- 7 75E 3.4.1.1.1.2 Preservative criteria, Unless otherwise specified (see 6.2.1) contact preservatives shall be in accordance with P-19 or P-21 of MIL-P-116 (see 3.4-.1.1.2.5). Preservatives shall be .applied only to couplings, fittings, and metal parts subject to corrosion. Preservatives shall

45、 not be applied to fabric, rubber, rubber-impregnated parts, plastic, or nonferrous metals or to surfaces that are painted, plated, coated, or that are inherently resistant to corrosion. Application of preservatives to couplings and other fittings attached to.hose, shall be in a manner to ensure a c

46、omplete homogenous coating. Preser- vative compound shall not be applied to any metal surfaces of hose, tubing, or fittings intended for installation or use in conjunction with oxygen systems (see 3.4.1.1.1.3.5). 3.4.1.1.1.3 Unit protection. 3.4.1.1.1.3.1 Hose or hose.assemblies. Hose or hose assemb

47、lies shall be supplied in coils, reels, or in straight lengths as specified (see 6.2.1), or as specified in the applicable commodity specification, and shall be unit pro- tected as specified herein for the required form (coil, reel, or straight length). 3.4.1.1.1.3.1.1 Hose and tubing ends with or w

48、ithout fittings. Open ends of hose and tubing, with or without fittings, shall be sealed with plugs or caps that will provide protection against entry of all foreign material. Hydraulic hose with or without fittings, shall be sealed with plugs or caps in accordance with MIL-C-5501 at the option of t

49、he contractor. Alternatively, open ends of hose and tubing, except hydraulic hose, may be sealed with grease- proof barrier material in accordance with type I, grade A, class 2 of ML-B-121. Barrier material, when used, shall extend a minimum of 4 inches over the open ends onto the body of the hose or tubing. Barrier material shall be secured with a minimum of 1-inch wide, water-resistant pressure-sensitive tape. Unless otherwise specified (see 6.2.1), hose o