NAVY MIL-DTL-60296 B-2005 INITIATOR CARTRIDGE ACTUATED DELAY M10 M31 M32 M72 M114 METAL PARTS ASSEMBLY《M10 M31 M32 M72 M114型金属零件装配 延时弹筒驱动引发器》.pdf

《NAVY MIL-DTL-60296 B-2005 INITIATOR CARTRIDGE ACTUATED DELAY M10 M31 M32 M72 M114 METAL PARTS ASSEMBLY《M10 M31 M32 M72 M114型金属零件装配 延时弹筒驱动引发器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-60296 B-2005 INITIATOR CARTRIDGE ACTUATED DELAY M10 M31 M32 M72 M114 METAL PARTS ASSEMBLY《M10 M31 M32 M72 M114型金属零件装配 延时弹筒驱动引发器》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-DTL-60296B 3 March 2005 SUPERSEDING MIL-I-60296A 30 March 1990 DETAIL SPECIFICATION INITIATOR, CARTRIDGE ACTUATED, DELAY, M10, M31, M32,M72, M114 METAL PARTS ASSEMBLY This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This sp

2、ecification covers the requirements for the M10, M31, M42, M72, M114 Delay Cartridge Actuated Initiator Metal Parts Assembly (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not include

3、documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4,

4、 or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these d

5、ocuments are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see. 6.2). DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-A-2550 Ammunition, General Specification for AMSC N/A FSC 1377 DISTRIBUTION STATEM

6、ENT A: Approved for public release; distribution is unlimited. INCH POUND Comments, suggestions, or questions on this document should be addressed to Commander, Indian Head Division, Naval Surface Warfare Center, Technical Information Branch (Code 4230), 101 Strauss Avenue, Indian Head, Maryland 206

7、40-5035, or emailed to amanda.pennnavy.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil/ Source: http:/assist.daps.dla.mil - Downloaded: 2005-06-22T14:10ZCheck the source to verify

8、 that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60296B 2 DEPARTMENT OF DEFENSE STANDARDS MIL-STD-413 Visual Inspection Guide for Elastomeric O-Rings (Copies of these documents are available online

9、at http:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this documen

10、t to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation (see 6.2). Drawings 8594862 Initiator, Cartridge Actuated, Delay, Metal Parts Assembly 8798143 Box, Fiberboard (Inner) Packing, Ammunition for Initiator, Cartridge Actuated, Delay, M10, M30A1

11、, M31, M32A1, M42, M43A1, M72, M92, or M114 8798142 Box, Packing, Ammunition, for Initiator, Cartridge Actuated, Delay, M10, M30A1, M31, M32A1, M42, M43A1, M72, M92, or M114 9216933 Box, Fiberboard (Outer) Alternative, Packing Ammunition, for Initiator, Cartridge Actuated, Delay, M10, M30A1, M31, M3

12、2A1, M42, M43A1, M72, M92, or M114 (Application for copies should be addressed to Commanding Officer, Naval Surface Warfare Center, Indian Head, Technical Information Branch (Code 4230), Indian Head, MD 20640.) 2.3 Non-Government publications. The following documents form a part of this document to

13、the extent specified herein. Unless otherwise specified, the issues of the documents, which are DOD adopted, are those listed in the issue of the DODISS cited in solicitation. Unless otherwise specified, the issues of documents not listed in DODISS are the issues of the documents cited in the solici

14、tation (see 6.2). AMERICAN NATIONAL STANDARD INSTITUTE/AMERICAN SOCIETY FOR QUALITY ANSI/ASQ Zl.4 Sampling Procedures and Tables for Inspection by Attributes ANSI/ASQ A8402 Quality Management and Quality Assurance - Vocabulary (Copies of these documents are available online at http:/webstore.ansi.or

15、g/ansidocstore/default.asp, or from the American Society for Quality, PO Box 3005, 611 E. Wisconsin Ave., Milwaukee, WI 53201-4606.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Noth

16、ing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. Source: http:/assist.daps.dla.mil - Downloaded: 2005-06-22T14:10ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproductio

17、n or networking permitted without license from IHS-,-,-MIL-DTL-60296B 3 3. REQUIREMENTS 3.1 First article. When specified in the contract or purchase order (see 6.2), a sample shall be subjected to first article inspection (see 4.4 and 6.3). 3.2 Materials. All materials used in the manufacture of th

18、e initiators shall conform strictly to the specifications referred to on the respective drawings unless specific approval in writing covering a departure therefrom has been obtained from the cognizant Navy design activity prior to manufacture. When alternate materials or methods of manufacture are s

19、pecified on the drawings, the bidders selections shall be clearly stated in the proposal. 3.2.1 Raw Material. The contractor shall be responsible for selecting from the classification list contained in the raw material specification the surface and physical condition of the raw material intended for

20、 use in manufacture. 3.3 Hardness and other physical properties. Hardness and other physical properties required by the drawing shall be uniform throughout the part within specified tolerances. Requirements for all alloy steel parts shall be achieved by quenching and tempering. 3.4 Hydrostatic press

21、ure. The initiator chamber and cap shall withstand a hydrostatic pressure of 5500 to 6500 pounds per square inch (psi) for 15 seconds, minimum, without deformation or mechanical failure (see 6.4.1). 3.5 Shear pin strength. The shear pin, after application of protective finish, shall shear when a loa

22、d of 41 5 pounds is applied at the steady rate of 0.125 inch per minute. 3.6 Metal parts assembly. Parts shall be combined to produce an assembly which conforms to the requirements of the metal parts assembly drawing. All threaded joints shall be assembled handtight. 3.7 Protective finish. Protectiv

23、e finish shall be in accordance with the applicable specifications and shall apply to all surfaces of the component regardless of contour configuration. 3.8. Residual magnetism. The metal parts assembly shall not deflect the indicator of the compass more than five degrees in either direction using p

24、rocedures in 4.6.5. 3.9 Workmanship. The requirements for workmanship are as specified on the applicable drawings, referenced specifications and the following: 3.9.1 Metal defects. All components shall be free from cracks, splits, cold shuts, inclusions, porosity or any similar defect. 3.9.2 Burr. N

25、o part shall have a burr which might interfere with the assembly or function of the item or which might be injurious to personnel handling the item. 3.9.3 Foreign matter. No part or assembly shall contain chips, dirt, grease, rust, corrosion or other foreign matter. Source: http:/assist.daps.dla.mil

26、 - Downloaded: 2005-06-22T14:10ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60296B 4 4. VERIFICATION 4.1 Classification of Inspections. The inspection requirements spe

27、cified herein are classified as follows: a. First article inspection (see 4.4) b. Quality conformance inspection (see 4.5). 4.1.1 Quality assurance terms and definitions. Reference shall be made to ANSI/ASQ A8402 to define the quality assurance terms used. 4.1.2 Inspection. Inspection shall be in ac

28、cordance with MIL-A-2550. 4.3 Inspection conditions. Unless otherwise specified (see 6.2), all inspections shall be performed under the following conditions: a. Temperature: Room ambient 68 to 77 F b. Altitude: Sea level c. Humidity: 50 percent relative, maximum d. Atmospheric pressure: 14.7 psia 4.

29、4 First article inspection. At the beginning of regular production, the contractor shall submit an initial production sample to a Government approved facility for evaluation. The sample shall consist of 5 metal parts assemblies, 9 sets of unassembled parts, 1 set of unassembled parts without plating

30、 or final protective finish and 50 shear pins from the same lot of shear pins tested by the contractor. The sample shall be manufactured in the same manner, using the same materials, equipment, processes and procedures as used in regular production. All parts and materials, including packaging and p

31、acking, must be the same as will be used for regular production and shall be obtained from the same source of supply. After inspection and provisional acceptance at source, the first article sample shall be inspected for all requirements of the drawings and specifications. The Government reserves th

32、e right to require new first article samples until such time as an acceptable sample is submitted (see 6.3). 4.5 Quality conformance Inspection. 4.5.1 Lot. 4.5.1.1 Submission of product. Unless otherwise specified by the contracting activity, formation and identification of lots shall be in accordan

33、ce with ANSI/ASQ Z1.4. 4.5.1.2 Size of lot. For the purpose of identif ication and shipment, the shipping lots of metal parts assemblies shall consist of 600 assemblies, maximum, provided the homogeneity requirements of inspection lots have been retained. 4.5.2 Examination. One-hundred percent exami

34、nation shall be performed for all critical defects. Examination for major and minor defects shall be performed on a defect basis in accordance with the classification of defects. Four power (4) magnification may be used in performing visual examination for such defects as burr and foreign matter. In

35、spection for rubber O-rings shall be in accordance with MIL-STD-413. When compliance with the applicable requirement is in doubt as a result of visual examination, the characteristic shall he measured or gaged to determine acceptability. All nonconforming material shall be rejected. Source: http:/as

36、sist.daps.dla.mil - Downloaded: 2005-06-22T14:10ZCheck the source to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60296B 5 4.5.2.1 Retainer, Cartridge, Drawing 8594860, covering a detail o

37、f Drawing 8594862. Characteristic Defect Method of Inspection Critical 1 Metering slots in base missing Visual Major 101 Pitch dia meter of thread, max Gage 102 Minor diameter of thread, max Gage 103 Concentricity of cavity with pitch diameter of thread Gage 104 Concentricity of counterbore with cav

38、ity Gage 105 Perpendicularity of pitch diameter of thread with base Gage 106 Symmetry of metering slots in base with body Gage 107 Diameter of cavity, max Gage 108 Depth of cavity Gage 109 Depth to bottom of counterbore Gage 110 Depth of metering slots in base Gage 111 Length of effective thread, mi

39、n Gage 112 Length of thread, max Gage 113 Internal radius at mouth of cavity Gage 114 Total length Measure 115 Width of metering slots in base Measure 116 Drill point in base, max Measure 117 Number of elongated slots incorrect Visual 118 Thread damaged or not full Visual 119 Metal defective Visual

40、120 Protective finish inadequate or defective Visual 121 Surface finish on internal radius and base improper Visual 122 Burr Visual 123 Foreign matter present Visual Minor 201 Pitch diameter of thread, min Gage 202 Diameter of cavity, min Gage 203 Diameter of counterbore Gage 204 Diameter of head Ga

41、ge 205 Depth of counterbore Gage 206 Diameter of body Measure 207 Length of elongated slots Measure 208 Length of head Measure 209 Width of elongated slots Measure 210 Location of elongated slots Measure 211 Angle between head and body Measure 212 Angular location of metering slots Visual 213 Markin

42、g missing, incorrect or illegible Visual 214 Profile of elongated slots Visual 215 Radius missing or incorrect Visual 216 Surface finish improper, except as otherwise classified Visual Source: http:/assist.daps.dla.mil - Downloaded: 2005-06-22T14:10ZCheck the source to verify that this is the curren

43、t version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60296B 6 4.5.2.2 Chamber, Initiator, Drawing 8594857, covering a detail of Drawing 8594862. Characteristic Defect Method of Inspection Critical 1 Absence of output port Visu

44、al Major 101 Pitch dia meter of large thread, min Gage 102 Major diameter of large thread, min Gage 103 Pitch diameter of small thread, min Gage 104 Major diameter of small thread, min Gage 105 Concentricity of counterbore with pitch diameter of large thread Gage 106 Concentricity of datum diameter

45、with small thread Gage 107 Diameter of counterbore Gage 108 Depth of cavity Gage 109 Thickness of wall, min Gage 110 Location of datum diameter Gage 111 Profile of gas port Gage 112 Thread damaged or not full Visual 113 Chamfer at base of cavity missing or incorrect Visual 114 Metal defective Visual

46、 115 Protective finish inadequate or defective Visual 116 Surface finish at end of gas port improper Visual 117 Burr Visual 118 Foreign matter present Visual Minor 201 Pitch diameter of large thread, max Gage 202 Pitch diameter of small thread, max Gage 203 Diameter of cavity Gage 204 Diameter of ho

47、le Gage 205 Diameter of small thread pilot Gage 206 Diameter of large thread pilot Gage 207 Length of large thread pilot Gage 208 Length of gas port Gage 209 Thickness of wall, max Gage 210 Location of small thread Gage 211 Depth of counterbore Measure 212 Total length Measure 213 Length to end of l

48、arge thread Measure 214 Marking missing, incorrect or illegible Visual 215 Radius or chamfer missing or incorrect, except as otherwise classified Visual 216 Surface finish improper, except as otherwise classified Visual Source: http:/assist.daps.dla.mil - Downloaded: 2005-06-22T14:10ZCheck the sourc

49、e to verify that this is the current version before use.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-60296B 7 4.5.2.3 Pin, Shear, Drawing 8594745, covering a detail of Drawing 8594862. Characteristic Defect Method of Inspection Critical None defined Major 101 Diameter, max Gage 102 Total length, min Measure 103 Metal defective Visual 104 Protective finish inadequate or def