NAVISTAR TMS 9527-2009 Pinstriping.pdf

《NAVISTAR TMS 9527-2009 Pinstriping.pdf》由会员分享，可在线阅读，更多相关《NAVISTAR TMS 9527-2009 Pinstriping.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar Inc. DECEMBER 2009 Page 1 of 3 NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER: TMS

2、-9527 TITLE: Pinstriping CURRENT REV No.: 0912 DATE: December 2009 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: Rev B-1, August 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, eq

3、uipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. Change Notice: Replaced “Internat

4、ional Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; added CEMS B-50 requirement; editorial changes. Reference: File 50-7 Keywords: Pinstriping 1.0 APPLICATION This specification covers the application of pinstriping to sleeper boxes or cabs that have been finished pain

5、ted with thermosetting acrylic enamels or urethane paints. 2.0 SCOPE This specification covers surface preparation, general performance requirements and material sources. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must

6、 comply with the requirements of the CEMS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following standards, specifications and regulations are referenced in this specification. Quality System Standard ISO 9001 o

7、r TS-16949 AATCC TM 8 CFR Title 29, Section 1910 ASTM D 1682 NAVISTAR Manufacturing Std.MS- D-13 NAVISTAR Eng. Design Std. A-16 NAVISTAR CEMS B-50 NAVISTAR TMS-9543 4.0 REQUIREMENTS 4.1 Surface Preparation Cabs shall be thoroughly washed to remove dust, dirt and soaps used in the windshield installa

8、tion. 4.1.1 All areas to be pinstriped shall be cleaned with a prep solvent. 4.1.2 A very slight abrasion with a Scotch-Brite (fine grit) pad is permitted in the distinct pattern to be pinstriped. This must be restricted to areas that will be covered by the pinstriping and shall not mar or detract f

9、rom the appearance of the paint finish. 4.1.3 All areas to be pinstriped shall be wiped with Acrylic Adhesion Promoter and allowed to set 30 minutes before applying the pinstriping. NUMBER: TMS-9527 TITLE: Pinstriping REVISION: 0912 This document is restricted and may not be sent outside Navistar In

10、c. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar Inc. DECEMBER 2009 Page 2 of 3 4.2 Pinstriping Application Add Stickum to the One Shot Lettering Enamel, 6 drops per oz. paint. 4.2.1 Apply pinstriping. 4.2

11、.2 Allow pinstriping to cure before moving finished unit outside and exposing to moisture and cold temperatures. 4.3 Performance Requirements The pinstriping shall be uniform in application and color. The pinstriping shall exhibit good adhesion to the topcoat paint and shall not be removed by typica

12、l high pressure truck wash wands or brushes or when exposed to moisture and freezing conditions. 5.0 QUALITY Parts shall be uniform in color and texture and match appearance of approved samples. 6.0 SOURCE APPROVAL AND QUALITY CONTROL 7.1 Supplier Requirements All suppliers to Navistar are required

13、to be registered to ISO 9001 Quality System Requirements. Navistar will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification with an accredited

14、registrar and must furnish copies of registration certificates to their Navistar Corporate Buyer upon request. 6.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchaser. No chan

15、ges in formulation or processing practices are permitted without approval. In the event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify Materials Engineering, Truck Development and Technology Center,

16、and Navistar Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with

17、 the request for change. 6.3 Process Control The supplier shall either perform and/or report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process

18、 capable of providing all required properties. The part supplier and the plant metallurgist and/or the quality control manager of the using Navistar plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING, PACKING AND IDENTIFICATION (Not Applicable) 8.0 DESIGNATION

19、ON DRAWINGS Pinstriping per TMS-9527 NUMBER: TMS-9527 TITLE: Pinstriping REVISION: 0912 This document is restricted and may not be sent outside Navistar Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar I

20、nc. DECEMBER 2009 Page 3 of 3 9.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck Development and Technology C

21、enter 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ 10.0 APPROVED MATERIALS AND SOURCE Material Source Acrylic Adhesion Promoter Bryne Sign Supply, Inc. Stickum 1880 Train Avenue One Shot Lettering Enamel Cleveland, Ohio 44113 Phone: (216) 781-4340