NAVISTAR CEMS B-51-2013 Dry Film Lubricant.pdf

《NAVISTAR CEMS B-51-2013 Dry Film Lubricant.pdf》由会员分享，可在线阅读，更多相关《NAVISTAR CEMS B-51-2013 Dry Film Lubricant.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、This document is restricted and may not be sent outside Navistar, Inc. or eproduced without permision from Corprate Technical Stanars. Spliers are rquire to asume al patet liabilty. 2013 by Navistar, Inc. JUNE 2013 Page 1 of 3 NAVISTAR, INC. CEMS (CORPRATE NGIERING ATRIAL SPECIFCATION) NUMBER: CEMS

2、B-51 TILE: Dry Film Lubricant CURENT ISUE DATE: JN 2013 WRITEN/REVIWED BY: Materials Engiering APROVED BY: Materials Engiering SUPERSEDS ISUE OF: APRIL 2013 PRINTED COPIES OF THIS DOCUENT UST BE VRIFED FOR CURENT REVISON This pecifcation may invole hazrdous materials, equipment, and procedures. This

3、 pecifcation does not purport o adres al of te safty isues socited wit its se. Th usr is rsosible to cnslt apropriat safty halth racties an to trmine th plicabilty of regulatory limits prior to se. Cange Notic: Aded an rved suplier to Section 9.0. 1.0 APLICATION This pecifcation covers the rquiremnt

4、s for asolid film lubricant coating containig molybdenum disulfid and ther lubricating pigts used n fastenrs to lwer the efiet of rictin, rce wear, miiiz mtali dhesion f parts oprtig dry and provid god corsin resitace on th thrde sections of stenrs. This coting is uitable for iternal threas f nuts a

5、d taping plates, and extrnal thrads f blts ad studs. 2.0 SCOPE This pecifcation covers the gneral coating requiremnts, quality, source aproval nd quality control, packing, shipig, and intifcation requirmnts, ad esigntion drwings. 2.1 Restricted Chemical Substcs Efctiv April 1, 2013 l produt suplied

6、to the rquiremnts of this pecifcation must comply with te rquiremnts of the CEMS B-50 scifcation. 3.0 REFRENCE DOCUENTS Unles otherwise specifed the latest isue of al refrenced standars hal aply. The folwing stadars, pcifcations, an rgultions ar refrncd i this pecifction: Quality Sstem Standar ISO 9

7、01 or TS-1694 CEMS B-50 NAVITAR Mufcturing tandar M-D-13 4.0 GENRAL REQUIREMNTS .1 Coating equirements 4 ti C ad Apearnce The cure parmetrs for the cotig shal be dtermined using the apropriate time/tmperature rlationshi rcoend by the mnufctur to achive the dsird erforanc. Th cr cyle shuld t afet h m

8、chanical or diensional prertis of te parts bing cotig. 4.11 The curd coating sl be sufictly dmag rsitant o revt hipin or ther coating removal dring rml hadling and shiping of prts. NUMBER: CS B-51 TILE Dry Film Lubricant CURENT ISUE DATE: JN 2013 This document is restricted and may not be sent outsi

9、de Navistar, Inc. or eproduced without permision from Corprate Technical Stanars. Spliers are rquire to asume al patet liabilty. 2013 by Navistar, Inc. JUNE 2013 Page 2 of 3 4.12 Coating shal have auniform apearnce and be fre of tears, runs, and flaked ares. ti Coverg 4.1.2.1 The cating is adip-sin

10、coating whic provides anti-seizng and controled frictional proertis. is coating roces des ot enrate hyrog; howver, pre-treatmnt press, i.e, acid ickling could use hydrgn asorpti. Thickns f cating shal b 5 -20. 4.1.3 Ceficent of Fictio Coeficnt of rictin of the coated parts hal be .03 -.07 when measu

11、red per ASTM D2714. 4.1.4 Heat Resitace This mtril shl rmain stable up to the tmperature of + 260 Celsius. 4.1.5 Salt Spray Resitce The tst ecimen shal show no evidence of corsion, and the coating shal show no pinholes or spartion fro t metl, after tstig fr 72 hurs per ASTM B 17. 4.1.6 Adhesin The c

12、oating must not chip, flake or expose any base metal surface. A uniform deposit of powdery matril cliing t te tae shl nt b bjctionbl. 4.1.7 Inital Aproval Samples for inital proval shal be aceptd based on compliance to the rquiremnts of this specifcati. 5.0 QUALITY Al product suplied per this pecifc

13、ation shal be clean d fre from dirt, oils, harp edges, or defcts harmfl t rodct rforman. 6.0 SOURCE APROVAL ND QUALITY CONTROL 6.1 uplier equirements Al sliers to Internatioal Truck and Engie are rquired to be rgisterd to ISO 901 Quality Sstm Rquiremnts. Intertioal wil lso acpt TS-1694 rgistratin as

14、 long as the splier can lso flfil al AIG PAP (roductin Part Aproval Proces) documntaio d aprovl requiremnts. Supliers must mintain their rtifcation with an aredited registr nd must frnish copies of rgistration certifcts to their Interationl Corprat Buyr upo reqest. 6.2 Aoval Parts uplied gainst cont

15、racts or purchase orders citng this pecifcation shal be quivalent i al respects to those mples whi wer prv by the purcasr. No hges in formltio r rosing practis ar rmitd ithout aproval. In the vent hat cans i aterial, prerties, prcesi rties, construction, clr, r lbeling of t product re rquired, th su

16、plier shal notify Truk Devlopmnt ad Tehlgy Centr and Iternational Prhasing an Suplier Dvlopmet f the prosd chage(s). st dat indicatig cofrmce t l requiremts of this pcifcatin, tst samles, an ew or amene or upted Material Safty Dat Sht(s) (MSD), in aordne with CFR Titl 29, Part 190 shal be sbmit with

17、 te rquest for cange. NUMBER: CS B-51 TILE Dry Film Lubricant CURENT ISUE DATE: JN 2013 This document is restricted and may not be sent outside Navistar, Inc. or eproduced without permision from Corprate Technical Stanars. Spliers are rquire to asume al patet liabilty. 2013 by Navistar, Inc. JUNE 20

18、13 Page 3 of 3 The suplier shal either perform and report esults of test on specifc lots of parts produced using ISO 901 or TS-1694 guidlins, r provi staistical evidnce f th lt having ben r i astae of staistical control an with aproces capble of proiig al rquired proertis. The part suplier nd the pl

19、nt metalurgist and/or th qulity contrl maner of the sing Intrnational lnt may dtrmie tstig ad rportin requiremnts on speifc products. 7.0 SHIPING, PACKING AND IENTIFCATION hiping and ientifcation shal be in acordance with Manufacturing Standar D-13. 8.0 DESIGNATION DRAWINGS Finish per CEMS B-51 9.0

20、APROVED SOURCES E/M Engierd Coating olutions E/M 6340 10. TECHNICAL INFORMATION For further information related to the tchnical contet of this pecifcati, ctct: Supliers may purchase controled copies of this pcifction by tacting: Matrials Engiering and Technolgy Dept. 1040 W. North Aveue elrose Park, IL 6016 E-mail: MterialsEngieringN IHS Global In. 15 Invernes Way East Eglwod CO 8012-576 Phone: 1-80-54-79 E-mail: AutomtiveIHS.com Website: htp:/global.ihs.