INTERN TMS 6811-2009 Lubricant Power Steering《动力转向装置润滑剂》.pdf

《INTERN TMS 6811-2009 Lubricant Power Steering《动力转向装置润滑剂》.pdf》由会员分享，可在线阅读，更多相关《INTERN TMS 6811-2009 Lubricant Power Steering《动力转向装置润滑剂》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 1 of 3 NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER:

2、TMS-6811 TITLE: Lubricant, Power Steering CURRENT REV No: 0908 DATE: August 2009 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES ISSUE OF: Rev. K-1 - April 2003 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification may involve

3、 hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use. Change No

4、tice: Replaced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; added section 2.1 “Restricted Chemical Substances”; added section 10 “Technical Information”; editorial changes. Reference: File 30-8 Keywords: Lubricant; Power Steering Gear 1.0 APPLICATION Th

5、is specification covers a power steering fluid used in service systems (Fleetrite P/N XX990625, where XX is a 2 place alpha prefix identifying the current supplier). 2.0 SCOPE This specification covers the physical and chemical properties for a power steering fluid originally developed to meet Sagin

6、aw power steering specification requirements. It is suitable for use in other power steering systems, such as Ross and Sheppard. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the CEMS

7、B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified the latest issue of all referenced standards shall apply. The following Specifications, Standards, and Regulations are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 ASTM D 92 ASTM D 445 ASTM D 227

8、0 NAVISTAR Manufacturing Std. MS-D-13 ASTM D 96 ASTM D 482 ASTM D 2272 CFR 29, Part 1910 ASTM D 97 ASTM D 611 ASTM D 2983 NAVISTAR CEMS B-50 ASTM D130 ASTM D 665 ASTM D 3945 ASTM D 892 ASTM D 4951 4.0 REQUIREMENTS 4.1 Physical and Chemical Properties 4.1.1 Viscosity (ASTM D 445) At 100 C (212 F) kin

9、ematic, cSt (mm2/s), 6.8 minimum At 40 C (104 F) kinematic, cSt (mm2/s), 51.5 maximum At -40 C (-40 F) BROOKFIELD (ASTM D 2983), cP, 35,000 maximum Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without lice

10、nse from IHS-,-,-NUMBER: TMS-6811 TITLE Lubricant, Power Steering REVISION: 0908 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. A

11、UGUST 2009 Page 2 of 3 4.1.2 Viscosity Index (ASTM D 97) Shall be 160 185 4.1.3 Shear Stability (ASTM D 3945 Procedure A, 20 passes) Kinematic viscosity 100 C (212 F), cSt; 5.74 minimum 4.1.4 Pour Point (ASTM D 97) Shall be -42 C (-44 F) minimum 4.1.5 Flash Point (ASTM D 92) Shall be 175 C (347 F) m

12、inimum 4.1.6 Foaming (ASTM D 892) When tested at the following temperatures, foaming tendency and foam stability shall be as follows: Temperature Foam Tendency Foam Stability 24 C (75 F) 100 ml, max 0 93 C (200 F) 100 ml, max 0 24 C (75 F) after testing at 93 C (200 F) 100 ml, max 0 4.1.7 Water and

13、Sediments (ASTM D 96, Method A, without demulsifier or water) Shall be 0.05% maximum. 4.1.8 Zinc Content (ASTM D 4951) Shall be 40-60 ppm. 4.1.9 Phosphorus Content (ASTM D 4951) Shall be 200 ppm, minimum 4.1.10 Aniline Point (ASTM D 611) Shall be 90 - 102 C (200 - 216 F) 4.1.11 Ash (ASTM D 482, Proc

14、edure A) Shall be 0.02% maximum. 4.1.12 Oxidation Stability (ASTM D 2272) Shall be 200 minutes, minimum. 4.2 Corrosion Test (ASTM D 665, Procedures A and B, 24 hours) Must pass both procedures A and B. 4.3 Copper Strip Corrosion (ASTM D 130, 1 hour, 150 C (302 F) Shall be 3A rating, maximum. 4.4 Ste

15、ering Test Must be approved by Saginaw Power Steering Systems, TRW Commercial Steering Division, R. H. Sheppard Company, Bosch Braking Systems, and LUK Automotive Hydraulics. 5.0 QUALIFICATION Material submitted for qualification shall be accompanied by detailed test reports and certification that m

16、aterial supplied meets all requirements. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-6811 TITLE Lubricant, Power Steering REVISION: 0908 This document is restricte

17、d and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. AUGUST 2009 Page 3 of 3 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier Requirements All suppliers to N

18、avistar are required to be registered to ISO 9001 Quality System Requirements. Navistar will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certificatio

19、n with an accredited registrar and must furnish copies of registration certificates to their Navistar Corporate Buyer upon request. 6.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples, which were approved by

20、the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes occur in material properties, processing practices, or labeling, the supplier shall notify Materials Engineering at TDTC and Navistar Purchasing and Supplier Development of the

21、proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new/amended/updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Section 1910, shall be submitted with the request for change. 6.3 Process Control The supplier

22、shall either perform and report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part suppl

23、ier and the plant metallurgist and/or the quality control manager of the using NAVISTAR plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING AND IDENTIFICATION Shipping and identification shall be in accordance with Navistar Manufacturing Standard MS-D-13. When p

24、ackaged for resale, containers, packaging and identification shall be in accordance with requirements set forth by the Parts Marketing Division of the Parts Operation at Cantera in Warrenville, Illinois. 8.0 DESIGNATION ON DRAWINGS Power Steering Lubricant per TMS-6811 9.0 APPROVED SOURCE Shell Powe

25、r Steering Fluid 51204 (Shell Code 20631) 10.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck Development and

26、 Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-