GMW GMW15921-2012 Adhesion Requirements for Bonding Exterior Glass Reinforced Thermoset Plastics Issue 2 English.pdf

《GMW GMW15921-2012 Adhesion Requirements for Bonding Exterior Glass Reinforced Thermoset Plastics Issue 2 English.pdf》由会员分享，可在线阅读，更多相关《GMW GMW15921-2012 Adhesion Requirements for Bonding Exterior Glass Reinforced Thermoset Plastics Issue 2 English.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 WORLDWIDE ENGINEERING STANDARDS Material Specification GMW15921 Adhesion Requirements for Bonding Exterior Glass Reinforced Thermoset Plastics Copyright 2012 General Motors Company All Rights Reserved July 2012 Originating Department: North American Engineering Standards Page 1 of 5 1 Introduction

2、1.1 Scope. This specification covers the performance requirements for an adhesive or adhesive system suitable for bonding thermoset plastics, Sheet Molding Compound (SMC) and Structural Reaction Injection Molded (SRIM) in exterior applications. 1.2 Typical Applications. Exterior applications of all

3、vehicles. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. ASTM D3163 ASTM D5573 ISO 4587 ISO 11343 ASTM D5041 2.2 GM Standards/Specifications. GMW3059 GMW14124 GMW14729 GMW15288 GMW3221 2.3 Additional References.

4、 TMC003 Material Safety Data Sheet guidance documents (available at ). 3 Test Preparation and Evaluation 3.1 Resources. 3.1.1 Calibration. The test facilities and equipment shall be in good working order and shall have a valid calibration label. 3.1.2 Alternatives. Alternate test facilities and equi

5、pment may also be used. However, all measuring variables as specified in this standard shall be determined correctly with respect to their physical definition. 3.1.3 Facilities. Not applicable. 3.1.4 Equipment. 3.1.4.1 Substrate coupons, 25 mm x 101 mm x 2.5 mm and 101 mm x 152 mm x 2.5 mm. 3.1.4.2

6、Suitable bonding fixture. 3.1.4.3 Water soak chamber capable of maintaining 54 C 2 C. 3.1.4.4 Universal tensile test machine capable of measuring loads at an accuracy of 1%. 3.1.4.5 Side Impact machine as described in ISO 11343. 3.1.4.6 Heated chamber capable of maintaining 82 C 2 C. 3.1.4.7 Oven ca

7、pable of maintaining 70 C 2 C. 3.1.4.8 Freezer capable of maintaining -30 C 2 C. 3.1.4.9 Sixty degrees (60) wedge as described in ASTM D5041. 3.1.5 Test Vehicle/Test Piece. See specific test. 3.1.6 Test Time. Not applicable. 3.1.7 Test Required Information. Not applicable. 3.1.8 Personnel/Skills. No

8、t applicable. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15921 Copyright 2012 General Motors Company All Rights Reserved July 2012 P

9、age 2 of 5 3.2 Preparation. See specific test. 3.3 Conditions. 3.3.1 Environmental Conditions. See specific test. 3.3.1.1 Sample Conditioning. All samples are to be conditioned prior to each requirement test to GMW3221, Code A. 3.3.2 Test Conditions. See specific test. 3.4 Instructions. See specific

10、 test. 3.5 Data. Not applicable. 3.6 Safety. This standard may involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and

11、health practices and determine the applicability of regulatory limitations prior to use. 3.7 Documentation. Samples of components or material released to this standard shall be tested for conformity with the requirements of this standard and approved by the responsible GM Department prior to the sta

12、rt of delivery of production level components or materials. Any change to the component or material, e.g., design, function, properties, manufacturing process and/or location of manufacture requires a new release of the product. It is the sole responsibility of the supplier to provide the customer,

13、unsolicited, with documentation of any change or modification to the product/process, and to apply for a new release. If not otherwise agreed to, the entire verification test shall be repeated and documented by the supplier prior to start of delivery of the modified or changed product. In some cases

14、, a shorter test can be agreed to between the responsible GM department and the supplier. 3.7.1 Test Results. Report the following: 3.7.1.1 The average lap-sheer and side impact strength along with standard deviation of each sample set. 3.7.1.2 The average wedge failure initiation energy and failure

15、 propagation energy along with standard deviation of each sample set. 3.7.1.3 The failure mode and strength (or energy) of each specimen according to ASTM D5573. 3.7.2 Deviations from This Standard. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shal

16、l be specified on component drawings, test certificates, reports, etc. 4 Requirements and Procedure 4.1 Physical Properties (Uncured Adhesive System). The adhesive and bonding method must be compatible with production systems. 4.2 Physical Properties/Requirements (Cured Adhesive System). 4.2.1 Paint

17、 Compatibility. The adhesive system must be compatible with the proposed paint systems and processes. 4.2.2 Process Compatibility. The cured adhesive system must meet all performance criteria specified in this standard (see 3.3) after going through the production process for the intended application

18、. 4.2.3 Lap Shear and Side Impact Samples. 4.2.3.1 Specimens shall be prepared according to the procedure outlined in ASTM D3163. Caution: Cure must be compatible with the intended plant cure schedule. This includes initial cure and oven exposures at the sub-assembler as well as the GM assembly plan

19、t. 4.2.3.2 A sample set shall consist of a minimum of 5 specimens. 4.2.3.3 Lap shear specimens shall be tested according to the procedure outlined in ISO 4587. 4.2.3.4 Side impact specimens shall be tested according to the procedures outlined in ISO 11343. 4.2.3.5 All samples must demonstrate cohesi

20、ve failure within the adhesive or fiber tear of the substrate in all test conditions. Adhesive failure is not acceptable unless otherwise stated. 4.2.3.6 Substrate fracture, below minimum performance requirements (3.3), is to be considered a no-test condition, and the test repeated or sample rejecte

21、d. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15921 Copyright 2012 General Motors Company All Rights Reserved July 2012 Page 3 of 5

22、4.2.3.7 Environmental Conditioning. 4.2.3.7.1 Two (2) sample sets shall be maintained at room conditions 23 C 2 C and will be referred to as initial. 4.2.3.7.2 Two (2) sample sets will be equilibrated to -30 C. 4.2.3.7.3 Four (4) sample sets shall be exposed to water soak at 54 C for a period of 7 d

23、ays. For sets tested wet, test within 15 minutes of removal from water. 4.2.3.7.4 Two (2) sample sets shall be exposed to the cycle as described in GMW14124 (Cycle G, 30 cycles; 6 weeks). 4.2.3.7.5 Two (2) sample sets shall be exposed to the cycle described in GMW15288 (20 cycles; 4 weeks). 4.2.3.7.

24、6 Two (2) sample sets shall be exposed to condensing humidity at 38 C for 8 weeks (GMW14729). 4.2.3.7.7 Two (2) sample sets shall be aged at 70 C for 8 weeks. 4.2.3.7.8 One (1) sample set shall be equilibrated at 82 C. Table 1: Lap-Shear Requirements Environment Test Condition Strength, kPa, Minimum

25、 SMC SRIM Initial Room temperature (RT) 3400 10 000 -30 C -30 C 3400 10 000 82 C 82 C 1400 10 000 54 C Water Soak Wet (tested within 15 minutes) 2700 10 000 54 C Water Soak 24 h recovery, RT 3400 10 000 GMW14124 (Cycle G, 6 weeks) 24 h recovery, RT 3400 10 000 GMW15288 (4 weeks) 24 h recovery, RT 34

26、00 9 500 GMW14729 (8 weeks) 24 h recovery, RT 3400 10 000 70 C Age (8 weeks) 24 h recovery, RT 3400 10 000 Table 2: Side Impact Requirements Environment Test Condition Strength, J, Minimum SMC SRIM Initial Room temperature (RT) 3.5 12 -30 C -30 C 3.5 12 54 C Water Soak Wet (tested within 15 minutes)

27、 3.5 12 54 C Water Soak 24 h recovery, RT 3.5 12 GMW14124 (Cycle G, 6 weeks) 24 h recovery, RT 3.5 12 GMW15288 (4 weeks) 24 h recovery, RT 3.5 12 GMW14729 (8 weeks) 24 h recovery, RT 3.5 12 70 C Age (8 weeks) 24 h recovery, RT 3.5 12 Copyright General Motors Company Provided by IHS under license wit

28、h General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15921 Copyright 2012 General Motors Company All Rights Reserved July 2012 Page 4 of 5 4.2.4 Wedge Samples. 4.2.4.1 Specimens shall be prepared according to

29、 the procedure outlined in ASTM D5041, Section 7. Plaques shall be 101 mm x 152 mm x 2.5 mm. Bond area shall be 101 mm x 51 mm. Bond gap shall be 0.8 mm 0.25 mm. Caution: Cure must be compatible with the intended plant cure schedule. This includes initial cure and oven exposures at the sub-assembler

30、 as well as the GM assembly plant. 4.2.4.2 A sample set shall consist of a minimum of 5 specimens. 4.2.4.3 Wedge specimens shall be tested according to procedure outlined in ASTM D5041 except use a 60 degrees wedge. 4.2.4.4 Environmental Conditioning. 4.2.4.4.1 One (1) sample set shall be maintained

31、 at room conditions 23 C 2 C and will be referred to as initial. 4.2.4.4.2 One (1) sample set shall be equilibrated at 82 C. 4.2.4.5 Wedge Requirements. Wedge samples are for information only and have no set load or failure mode requirements. 5 Provisions for Shipping Not applicable. 6 Notes 6.1 Glo

32、ssary. Not applicable. 6.2 Acronyms, Abbreviations, and Symbols. GHS Globally Harmonized System of Classification Labeling of Chemicals MSDS Material Safety Data Sheet RT Room Temperature SMC Sheet Molding Compound SRIM Structural Reaction Injection Molded 7 Rules and Regulations 7.1 Legal Regulatio

33、ns. All materials must satisfy applicable laws, rules, regulations and recommendations valid in the country of usage. 7.2 Language. In the event of conflict between the English and domestic language, the English language shall take precedence. 7.3 Inspection and Rejection. Samples of components or m

34、aterials released to a GM material specification shall be tested for conformity with the requirements of this material specification and approved by the responsible Engineering department prior to commencement of delivery of bulk supplies. A new approval must be received for any changes, e.g., prope

35、rties, manufacturing process, location of manufacture, etc. If not otherwise agreed, all testing and documentation normally required for initial release must be completed. It is the responsibility of the supplier to inform the customer in a timely manner, without solicitation, and to include documen

36、tation of all modifications of materials and/or processes and to apply for a new release. If not otherwise agreed, all release tests shall be repeated and documented by the supplier prior to commencement of delivery of non-conforming bulk supplies. In individual cases, a shorter test can be agreed t

37、o between the responsible Engineering department and the supplier. 7.4 Initial Source Approval. No shipments shall be made by any supplier until representative initial production samples have been approved by the appropriate Materials Engineering department(s) as meeting the requirements of this spe

38、cification. 7.5 Material Safety Data Sheets/Safety Data Sheets (MSDS/SDS). For new product submissions, or when a change in chemical composition of an existing product has occurred, a complete copy of the Material Safety Data Sheet/Safety Data Sheet must be submitted in compliance with the Globally

39、Harmonized System of Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW15921 Copyright 2012 General Motors Company All Rights Reserved July

40、 2012 Page 5 of 5 Classification and Labeling of Chemicals (GHS) requirements or other country-specific MSDS/SDS requirements. In addition, product MSDS/SDS submissions must be in compliance with specific country General Motors TMC003 Material Safety Data Sheet/Safety Data Sheet guidance documents w

41、here available. 7.6 All materials supplied to this standard must comply with the requirements of GMW3059, Restricted and Reportable Substances for Parts. 7.7 Approved Sources. Engineering qualifications of an approved source are required for this standard. Only sources listed in the GM Materials Fil

42、e, GM Supply Power, under this standard number have been qualified by Engineering as meeting the requirements of this standard. For other GM locations, the responsible Engineering group should be contacted to obtain the approved source in that individual country. 8 Coding System This standard shall

43、be referenced in other documents, drawings, etc., as follows: Material per GMW15921 9 Release and Revisions This standard was originated in May 2008. It was first approved by The Global Adhesives Committee in July 2008. It was first published in July 2008. Issue Publication Date Description (Organiz

44、ation) 1 JUL 2008 Initial publication. 2 JUL 2012 Revised external standards referenced in document. (Adhesives Global Subsystem Leadership Team) Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-