GMW GMW14162-2011 Colorfastness to Artificial Weathering Issue 2 English《人工风化的不褪色性 第2次出版(英文版本)》.pdf

《GMW GMW14162-2011 Colorfastness to Artificial Weathering Issue 2 English《人工风化的不褪色性 第2次出版(英文版本)》.pdf》由会员分享，可在线阅读，更多相关《GMW GMW14162-2011 Colorfastness to Artificial Weathering Issue 2 English《人工风化的不褪色性 第2次出版(英文版本)》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 WORLDWIDE ENGINEERING STANDARDS Test Procedure GMW14162 Colorfastness to Artificial Weathering Copyright 2011 General Motors Company All Rights Reserved June 2011 Originating Department: North American Engineering Standards Page 1 of 5 1 Scope Note: Nothing in this standard supercedes applicable la

2、ws and regulations. Note: In the event of conflict between the English and domestic language, the English language shall take precedence. 1.1 Purpose. This test method shall be used to determine the effects of weathering using a xenon-arc lamp source (artificial sunlight) to simulate extreme environ

3、mental conditions encountered inside a vehicle due to sunlight, heat and humidity. This method shall be used to evaluate the colorfastness, as well as being the artificial weathering method to evaluate degradation. This method describes four possible exposure cycles: Method A. Light and Dark Exposur

4、e Cycle (100 C, 420 nm). The cycle alternates between light and dark periods. This cycle is based on ISO 105-B06 exposure condition Number Three. Method B. Light Only Exposure Cycle (100 C, 300 to 400 nm). This cycle is based on ISO 105-B06 exposure condition Number Three. Method C. Light Only Expos

5、ure Cycle (115 C, 300 to 400 nm). This cycle is based on ISO 105-B06 exposure condition Number One. Method D. Light and Dark Exposure (89 C, 340 nm). The cycle alternates between light and dark periods. This cycle is based on ISO 105-B06 exposure condition Number Five (SAE J1885/SAE J2412 equivalent

6、 with SAE J2413 as the companion document). 1.2 Foreword. This test method was developed by the Global Textile Team to create a common method for evaluating colorfastness to artificial weathering. 1.3 Applicability. Not applicable. 2 References Note: Only the latest approved standards are applicable

7、 unless otherwise specified. 2.1 External Standards/Specifications. ISO 105-A02 SAE J2412 ISO 105-B06 SAE J2413 ISO 4892-1 SAE J2414 SAE J1885 2.2 GM Standards/Specifications. GMW6992 2.3 Additional References. None. 3 Resources 3.1 Facilities. Not applicable. 3.2 Equipment. 3.2.1 Method A. Test equ

8、ipment, according to ISO 105-B06, with the following machine setup shall be used: 3.2.1.1 Filters. Inner filter: Type S Borosilicate Outer filter: Soda Lime Appendix A defines the Spectral Power distribution for Type “S” Borosillicate/Soda Lime filter combination for Method A. 3.2.1.2 Temperature Se

9、nsor. Black Standard Temperature (BST). 3.2.1.3 Chamber (Dry Bulb) Temperature. Active. 3.2.1.4 Rack Panel Temperature. Active. 3.2.1.5 Radiation. Controlled at 420 nm. 3.2.2 Method B. Test equipment according to ISO 105-B06 with exposure apparatus B or C shall be used. 3.2.3 Method C. Test equipmen

10、t according to ISO 105-B06 with exposure apparatus B with 4lR+3WG or 10 WG filter system shall be used. 3.2.4 Method D. Test equipment according to ISO 105-B06 for exposure condition Number Five or SAE J2414/SAE J2413. 3.2.5 White-Standard Thermometer. The White Standard thermometer is in accordance

11、 with the Black Standard thermometer of ISO 105-B06. However, the metal plate is provided with a white cover according to ISO 4892-1. 3.3 Test Vehicle/Test Piece. Test material according to ISO 105-B06 shall be used. Copyright General Motors Company Provided by IHS under license with General Motors

12、CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14162 Copyright 2011 General Motors Company All Rights Reserved June 2011 Page 2 of 5 3.4 Test Time. The timing will be set based on the material specification requirement.

13、 3.5 Test Required Information. Not applicable. 3.6 Personnel/Skills. Not applicable. 4 Procedure Test specimens are exposed in a xenon-arc weathering device to artificial weathering conditions which simulate extreme environmental conditions encountered inside a vehicle due to sunlight, heat, and/or

14、 humidity. Test specimens are then evaluated for colorfastness (fade) or other modes of degradation. 4.1 Preparation. Test samples shall be prepared according to ISO 105-B06. A conditioning to GMW3221 Standard Conditioning of Organic Materials is not required. 4.2 Conditions. 4.2.1 Environmental Con

15、ditions. See 4.3.1. 4.2.2 Test Conditions. Deviations from the requirements of this standard shall have been agreed upon. Such requirements shall be specified on component drawings, test certificates, reports, etc. 4.3 Instructions. 4.3.1 Exposure Conditions. 4.3.1.1 Method A. Exposure conditions ac

16、cording to ISO 105-B06 Condition Three, but with parameters according to Table 1. Exposure begins in the Dark Period. The Dark and Light Periods are alternated until the required exposure level of kilojoules per square meter (kJ/m2) is met. The timing for the Light Period only is calculated from the

17、 required radiant exposure as: 6.3EQt Where: Q is the radiant exposure expressed in kilojoules per square meter E is the irradiance expressed in watts per square meter (or joules per square meter second) t is the time expressed in hours 3.6 is the conversion factor expressed in kiloseconds per hour

18、Appendix B identifies timing for typical required irradiation values. Table 1: Exposure Conditions for Method A Dark Period (“Light Off” Period) Note 1 Light Period (“Light on” Period) Note 1 Duration = (Time/Irradiation) 1 h 3.8 h at 1.2 W/m2 at 420 nm Test chamber temperature, C 38 2 C 65 3 C Blac

19、k Standard Temperature, C 38 2 C 100 3 C Relative humidity in test chamber, % 95 2% 20 10% Specimen spray Off Off Rack spray Off Off Conditioning water temperature, C. (This will be for some models or weatherometer only.) 40 4 C 66 4 C Note 1: Method A consists of five alternating Dark Periods (1 h

20、per each period) and five Light Periods (3.8 h per each period) in a 24 h duration with the test beginning in the Dark Period. 4.3.1.2 Method B. Exposure conditions shall be according to ISO 105-B06 Condition Three but with humidity of 0 to 20% relative humidity (RH). In addition to the Black Standa

21、rd Temperature of +100 C, a White Standard Temperature of +76 1 C is observed for information only. The timing (number of cycles) for the wide band exposure is calculated per the equation in 4.3.1.1. Appendix B displays timing for typical required radiant exposure values. Copyright General Motors Co

22、mpany Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14162 Copyright 2011 General Motors Company All Rights Reserved June 2011 Page 3 of 5 4.3.1.3 Method C. Exposure con

23、ditions shall be according to ISO 105-B06 Condition One but with humidity of 0 to 20% RH. In addition to the Black Standard Temperature of +115 C, a White Standard Temperature of 75 1 C is observed for information only. The timing (number of cycles) for the wide band exposure is calculated per the e

24、quation in 4.3.1.1. Appendix B displays timing for typical required radiant exposure values. 4.3.1.4 Method D. Exposure conditions shall be according to ISO 105-B06 Condition Five or SAE J2412/SAE J2413. 4.3.2 Exposure. Exposure shall be according to ISO 105-B06. The exposure shall be continued unti

25、l the required radiant exposure value as specified in the relevant material specification has been reached. The time until the required radiant exposure value has been reached is noted. 5 Data 5.1 Calculations. Visual assessment for colorfastness shall be made by a person with a trained eye. Compare

26、 the test specimen to a control sample and the gray scale (refer to ISO 105-A02) under standard lighting defined in GMW6992. All comparisons shall be made with like sized evaluation areas. Perform color and gloss measurements, if applicable. Calculate the differences between the unexposed control sa

27、mple of the start of test values of the unexposed sample and the exposed test specimen. Degradation evaluations to be completed and reported according to the methods defined in the relevant material specification. 5.2 Interpretation of Results. 5.2.1 Report the color change rating from visual assess

28、ment at required exposure level. Note any appearance or degradation changes seen that are not included on the color change rating scale. 5.2.2 If required, report the color machine measurements for color change using the CIELAB D65/10 measurements for DE*, DL*, DC*, DH*, Da*, Db* at each required ex

29、posure level. 5.2.3 If required, for information only, provide Standard Reference Manual (SRM) data for the days the test specimen was being tested. 5.2.4 Report all test parameters according to material specification. 5.3 Test Documentation. The results of the tests will be recorded in the Test Rep

30、ort. 6 Safety This standard may involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine

31、the applicability of regulatory limitations prior to use. 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. BST Black Standard Temperature RH Relative Humidity SPD Spectral Power Distribution SRM Standard Reference Manual 8 Coding System This standard shall be reference

32、d in other documents, drawings, etc., as follows: Test to GMW14162/A/640 kJ/m2/Rating 4 minimum Where: GMW = Validation area (GM Worldwide 14162 = Sequential number A = Method 640 kJ/m2 = Required radiant exposure value Rating 4 minimum = Required minimal gray scale rating to ISO 105-A02. 9 Release

33、and Revisions This standard was originated in June 2005. It was first approved by the Global Textile Team in October 2006. It was first published in October 2006. Issue Publication Date Description (Organization) 1 OCT 2006 Initial publication. 2 JUN 2011 Five year refresh of standard updated in cur

34、rent template. (Global Textiles Team) Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW14162 Copyright 2011 General Motors Company All Rig

35、hts Reserved June 2011 Page 4 of 5 Appendix A Figure A1: Spectral Power Distribution (SPD) for Filter Combination of Method A Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-G

36、M WORLDWIDE ENGINEERING STANDARDS GMW14162 Copyright 2011 General Motors Company All Rights Reserved June 2011 Page 5 of 5 Appendix B Table B1: Timing for Typical Exposures using Method A Required Radiant Exposure Q (Irradiance Value) Time for Radiant Exposure (Q) in kJ/m 5 Dark Periods + 5 Light Pe

37、riods = 24 h kJ/m Light Period Hours Dark Period Hours Total Test Time in Hours 320 74.0 19.5 93.5 640 148.0 38.9 186.9 960 222.0 58.4 280.4 Table B2: Typical Timing for Method B Required Radiant Exposure Q (Irradiance Value) Irradiance: 45 W/m Wide Band: (300 to 400) nm Irradiance: 60 W/m Wide Band

38、: (300 to 400) nm MJ/m Hours = Days Hours = Days 14 86 3.6 65 2.7 19 117 4.9 88 3.7 28 173 7.2 130 5.4 38 235 9.8 176 7.3 42 259 10.8 194 8.1 Table B3: Typical Timing for Method C Required Radiant Exposure Q (Irradiance Value) Irradiance: 70 W/m Wide Band: (300 to 400) nm Irradiance: 90 W/m Wide Ban

39、d: (300 to 400) nm MJ/m Hours = Days Hours = Days 14 56 2.3 43 1.8 19 75 3.1 59 2.4 28 111 4.6 86 3.6 38 151 6.3 117 4.9 42 167 6.9 130 5.4 Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-