FORD WSS-M99G173-A-2000 REFLECTIVE SLEEVING WOVEN POLYESTER ALUMINUM FOIL LAMINATED WITH ADHESIVE《带胶粘剂的铝箔层压聚酯机织反射套管》.pdf

《FORD WSS-M99G173-A-2000 REFLECTIVE SLEEVING WOVEN POLYESTER ALUMINUM FOIL LAMINATED WITH ADHESIVE《带胶粘剂的铝箔层压聚酯机织反射套管》.pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M99G173-A-2000 REFLECTIVE SLEEVING WOVEN POLYESTER ALUMINUM FOIL LAMINATED WITH ADHESIVE《带胶粘剂的铝箔层压聚酯机织反射套管》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2000 09 26 Revised Updated A. Cockma n 1997 05 02 Activated D. W. Whyte Printed copies are uncontrolled Page 1 of 3 Copyright 2000, Ford Global Technologies, Inc. REFLECTIVE SLEEVING, WOVEN POLYESTER, WSS-M9

2、9G173-A ALUMINUM FOIL LAMINATED WITH ADHESIVE 1. SCOPE This standard defines the material requirements for a polyester substrate with a polymeric adhesive laminating the substrate to an exterior aluminum foil . The polyester substrate is a combination of polyester monofilament and polyester multifil

3、ament. The final product can be either a sleeve version; or a flat tape with a hook and loop closure and a foil overlap to enclose the hook and loop closure. 2. APPLICATION This specification was released originally for material used to provide thermal protection for engine wires used in high temper

4、ature applications. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification o f materials. 3.1 QUALITY SYSTEM REQUIREMENTS Material suppliers and part producers must conform to the Companys Quality System Requirements. 3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMA

5、L ANALYSIS IR spectra and thermograms established for initial ap proval shall constitute the reference standard and shall be kept on file at the designated material laboratory. All samples shall produce IR spectra and thermograms that correspond to the reference standard when tested under the same c

6、onditions. 3.3 CONDITIONING AND TEST CONDITIONS All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/ - 2 C and 50 +/ - 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. ENGI

7、NEERING MATERIAL SPECIFICATION WSS-M99G173-A Page 2 of 3 Copyright 2000, Ford Gl obal Technologies, Inc. 3.4 POLYESTER PHYSICAL PROPERTIES 3.4.1 Polyester Monofilament Diameter 0.254 +/ - (ASTM D 204) 0.00762 mm 3.4.2 Polyester Multifilament Size, denier 1250 3.4.3 Tensile Strength, min (ASTM D 2256

8、) Polyester Monofilament , N 37.81 +/ - 6.67 Polyester Multifilament, N 33.36 +/ - 6.67 3.4.4 Elongation (ASTM D 2256) Polyester Monofilament, % 15 - 30 Polyester Multifilament, % 22 - 38 3.4.5 Linear Shrinkage (ASTM D 204, after 0.5 h at 175 C) Polyester Monofila ment, % 4.5 +/ - 1 Polyester Multif

9、ilament, % 4.5 +/ - 1 3.5 PEEL STRENGTH (foil from fabric) (ASTM D 904, 30 minute immersion at 23 +/ - 1 C) Samples are cut to 10 inches long. Each sample tested is subjected to one of the following fluids: disti lled water, 3 % salt water solution, 10W - 40 motor oil or brake fluid. Samples (includ

10、ing the overlap of the wrappable version) must meet at least one of the following requirements: Achieve peel strength value of 175.13 N/m, min Adhesion to the fabric sh all exceed the strength of the aluminum foil substrate. 3.6 LOW TEMPERATURE FLEXIBILITY No sign of cracking or delamination of the

11、foil laminate after the sleeve is held at - 40 C for 5 h, and then wrapped around a mandrel which is 2 times the nominal d iameter of the sleeve. Sample length for the test is 304.8 mm. ENGINEERING MATERIAL SPECIFICATION WSS-M99G173-A Page 3 of 3 Copyright 2000, Ford Gl obal Technologies, Inc. 3.7 T

12、HERMAL ENDURANCE No delamination of the foil from the fabric when the sleeve is held 30 mm above a 538 C radiant heat source for 6 h. Sleeve length to be 304.8 mm. Hose outside diam eter to be 3.175 mm less than sleeve diameter. Radiant Heat Source: PMI heater with a 32 x 7.62 cm flat face black sur

13、face or equivalent. (Note: heater output is 1100 watts, 240 volts at maximum power. 537.78 C is not maximum power.) 3.8 SUPPLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to

14、 making any changes to the material originally approved under this specification, wheth er or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify the affected Purchasing, and Materials Engineering activities (with reasons) of the proposed c

15、hanges. Upon notification of the Company, further instructions will be provided. Note: Suppliers should be prepared to provide test data and samples demonstrating compliance to this specification, if requested. Substance restrictions imposed by regulations or Company direction applies to the m ateri

16、als addressed by this document. The restrictions are identified in Restricted Substance Management Standard WSS - M99P9999 - A1. 4. APPROVAL OF MATERIALS Materials defined by this specification for direct supply to the Company must have prior approval. Certain materials subcontracted by part supplie

17、rs may also require prior approval. These include materials critical to the Companys business for regulatory, safety, environmental or compatibility requirements or contractual agreements. Suppliers desir ing approval of their materials shall first obtain an expression of interest from Purchasing, Design or Materials Engineering activity. Upon request, the Supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and au thorized representative of the test facility, demonstrating full compliance with all the requirements of this specification.