FORD WSS-M1H815-A-2008 FABRIC PAINT 1 PATTERN WOVEN JACQUARD UNLAMINATED TO BE USED WITH FORD WSS-M99P1111-A 《PAINT 1图案的不分层提花机织织物 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD WSS-M1H815-A-2008 FABRIC PAINT 1 PATTERN WOVEN JACQUARD UNLAMINATED TO BE USED WITH FORD WSS-M99P1111-A 《PAINT 1图案的不分层提花机织织物 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M1H815-A-2008 FABRIC PAINT 1 PATTERN WOVEN JACQUARD UNLAMINATED TO BE USED WITH FORD WSS-M99P1111-A 《PAINT 1图案的不分层提花机织织物 与标准FORD WSS-M99P1111-A一起使用 》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2008 12 04 N-STATUS No Replacement L. Schmalz, FNA / M. Montgomery, FOE 2003 02 26 Revised Para 3.0 inserted ; Para 3.1, 3.2, 3.3, 3.10,3.11, 4 deleted 1999 11 17 Activated N. Komatsu Printed copies are unco

2、ntrolled Page 1 of 2 Copyright 2008, Ford Global Technologies, Inc. FABRIC, PAINT 1 PATTERN, WOVEN JACQUARD, WSS-M1H815-A UNLAMINATED NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a woven jacquard polyester face fabric. 2. APPLICATION This specification was rel

3、eased originally for material used as an interior trim fabric for use in Mexico. 3. REQUIREMENTS In addition to the requirements listed herein, the fabric shall meet all requirements of WSS-M8P18-A1/A2/A3/A4 as applicable. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and par

4、t producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 FABRIC CONSTRUCTION 3.4.1 Fabric Count, +/- 5 % tolerance (ASTM D 3775) Warp 270 ends/10 cm Weft 130 picks/10 cm 3.4.2 Fabric Weight, range (FLTM BN 106-01) 335 +/- 30 g/m23.5 COMPOSITION (A

5、STM D 629) Fabric 100 % polyester ENGINEERING MATERIAL SPECIFICATION WSS-M1H815-A Page 2 of 2 Copyright 2008, Ford Global Technologies, Inc. 3.6 YARN CONSTRUCTION (ASTM D 1244) Warp 650 dtex f61, round, air texturized Weft 600 dtex f140, round, air texturized 3.7 METHOD OF DYEING Yarn dyed or as app

6、roved by Materials Engineering 3.8 FINISHED OPERATIONS As approved by Materials Engineering 3.9 FLAMMABILITY (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute Note: Not required on face fabric when used as a fully bonded composite. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 Purchase departments will ensure that both materials defined in this specification and shipped to any one assembly plant will be produced by one supplier only.