FORD WB900 APPENDIX E-1996 LOBED EXTERNAL DRIVE SYSTEM FOR THREADED FASTENERS《螺纹紧固件用有瓣外部驱动系统》.pdf

《FORD WB900 APPENDIX E-1996 LOBED EXTERNAL DRIVE SYSTEM FOR THREADED FASTENERS《螺纹紧固件用有瓣外部驱动系统》.pdf》由会员分享，可在线阅读，更多相关《FORD WB900 APPENDIX E-1996 LOBED EXTERNAL DRIVE SYSTEM FOR THREADED FASTENERS《螺纹紧固件用有瓣外部驱动系统》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、a4!ii!B WORLDWIDE STANDARD WB9OOAPPENDME DATE: 19% =OBER Lded External Drive System for Threaded Fasteners 1. SCOPE. This Appendix covers the dimensional and gauging requirements for a 6 lobed extemal drive system used on threaded studs and headless screws. 3 -. DIMENSIONS. The dimensions of studs a

2、nd headless screws are refaced in Fre El and Table El but shall meet the gauging requirements specified in clause 3. -7 2. GAUGING OF HEADLESS SCREW DRIVE FEATURES. 3.1 The wrenching height (K) shall be checked using the gauge specified in Figure E2 and Table E2. Parts shall be considered acceptable

3、 ifthe top surface of the lobed head lies flush with or extends beyond the top surface of the gauge as shown in F&m E2-A. 32 The outside diameter (A) of the drive feature shall be checked using the go gauge specified in Figure E2 and Table E2. Parts are considered acceptable if all of the lobed driv

4、e system enters the gauge as shown in Figure E2-B. 3.3 The fallaway of lobed drive features shall be checked using the gauge specified in Figure E2 and Table E2. parts are considered acceptable if the upper surface of the drive feature does not protrude above the top surface of the gauge as shown in

5、 Figure E2-C. 4. FORM AND POSITION. The concentricity of the outside diameter of the lobes to the inner diameter of the lobe valleys shall be checked with the gauge shown &Figure E3 and Table E3. Parts shall be considered acceptable if all of the lobed drive feature enters the gauge as shown in F&gu

6、m E3-A. The concentricity of the outside diameters of the lobes to the threaded portion of threaded studs and headless screws shall not exceed 0.25 Total indicator Reading when measured as shown in Figure E4. PAGE 1 OF 6 WORLDWIDE STANDARD WB9OOAPPENDIXE DATE: 1996 CXXOBER Lobed External Drive Syste

7、m for Threaded Fastenen Figure El. Table El. 1) Controlled by gauging PAGE 2 OF 6 8qiiB WORLDWIDE STANDARD WB9OOAPPENDIXE DATE: 1996 OCTOBER Lobed External Drive System for Threaded Fastenen Fire E2. Table E2. Ii I II Wrenching Height I Fallaway II Drive H K B E J S R.nd. A AA T X Size +038 +0.127 +

8、0.0076 +025 +0.25 938 +O.OOO +.0076 +0.0076 +.OOO +0.127 -038 -0.000 -0.0076 -0.00 -0.25 438 4.005 -Al025 6.0025 -.025 -0.127 El 3.18 0.508 1.7018 2.36 4.44 1.83 0.4191 2.3368 2.1082 0.554 10.58 E4 3.18 0.737 2.7432 2.36 5.64 1.57 0.673 1 3.7592 3.4038 0.940 Il.86 u E5 t 3.18 II 0.940 , 3.3528 , 2.7

9、7 I 6.91 I 1.75 I 0.9017 I 4.6482 I 4.2418 I 1.168 , II.65 II J3 1 3.18 11 0.991 1 3.9878 1 3.96 1 9.30 1 2.59 1 1.2573 ( 5.6134 ( 5.2832 1 1.372 1 12.17 If 11 E20 1 9.53 1 4.089 1 13.1572 1 11.10 I 27.00 I 7.37 I 3.6322 I 18.2626 t 16.8910 I 4.115 I 35.43 II E24 9.53 5.639 I 15.6972 I 14.27 ( 33.99

10、 9.50 I 4.7244 1 21.9456 ( 20.3962 I 5.359 38.77 II PAGE 3 OF 6 am) WORLDWIDE STANDARD WB 900 APPENDIX E DATE: 1996 mOI3ER Lobed External Drive System for Threaded Fasteners Fire E2-A ACCEPTABLE Figure E2-B Figure E2-C PAGE 4 OF 6 WORLDWIDE STANDARD WB 900 APPENDIX E DATE: 19% OCTOBER Lobed External

11、 Drive System for Threaded Fasteners Fire E3. Table E3. E-20 18.314 13.208 3.616 1.679 18.974 E-24 2 1.984 15.748 4.609 1.856 22.759 E-28 25.553 18.314 5.351 2.159 26.365 PAGE 5 OF 6 WORLDWIDE STANDARD WB9OOAPPENDlXE DATE: 1996 OCIOBEB Lobed External Drive System for Threaded Fasteners FiireE3-A Figure E4 PAGE 6 OF 6