FORD FLTM BO 115-02-2001 RESISTANCE OF PLASTICS TO ARTIFICIAL WEATHERING (Replaces FLTM BO 015-02 FLTM EU-BO 015-02)《塑料的人工候化耐受性 替代FLTM BO 015-02 FLTM EU-BO 015-02［替代 FORD FLTM BO 0.pdf

《FORD FLTM BO 115-02-2001 RESISTANCE OF PLASTICS TO ARTIFICIAL WEATHERING (Replaces FLTM BO 015-02 FLTM EU-BO 015-02)《塑料的人工候化耐受性 替代FLTM BO 015-02 FLTM EU-BO 015-02［替代 FORD FLTM BO 0.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM BO 115-02-2001 RESISTANCE OF PLASTICS TO ARTIFICIAL WEATHERING (Replaces FLTM BO 015-02 FLTM EU-BO 015-02)《塑料的人工候化耐受性 替代FLTM BO 015-02 FLTM EU-BO 015-02［替代 FORD FLTM BO 0.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 FORD LABORATORY TEST METHOD BO 115-02 Date Action Revisions 2001 03 28 Revised Editorial no technical change A. Cockman 1994 02 28 Printed copies are uncontrolled Page 1 of 2 Copyright 2001, Ford Global Technologies, Inc. RESISTANCE OF PLASTICS TO ARTIFICIAL WEATHERING Application This procedure is

2、 used to test the resistance of molded plastic parts to artificial weathering by exposure to ultraviolet energy, salt spray, heat and humidity. Apparatus Required Fluorescent Sunlamp Cabinet* A modified oven equipped with four Westinghouse FS 20T-12 fluorescent sunlamps is required. Oven* Approximat

3、e internal dimensions, 700 mm wide, 600 mm deep, 500 mm high, and capable of maintaining a temperature of 60 +/- 2 C. A Grieves-Hendry oven, Model PL-1 is suitable. Sunlamp Fixture* To be completely installed in the cabinet. 20 gauge steel box with screw cover. One 20 watt high power factor ballast

4、for each two lamps. Four fluorescent starter assemblies. Cover - 20 gauge steel with Alzak aluminum reflector overlay. Four pairs fluorescent lamp holders. Four Westinghouse FS 20T-2 fluorescent sunlamps. *The complete Fluorescent Sunlamp Cabinet is available from: Infra Corporation 5454 Dixie Highw

5、ay Waterford, MI 48095 U.S.A. Telephone: 810/623-0400 Humidity Cabinet The humidity cabinet must be maintained at 38 +/- 2 C and a relative humidity of 98 +/- 2 %. The moist air must be circulated in the cabinet by a fan or other suitable means. Test specimens must be suitably supported and arranged

6、 in the test cabinet so that no water can drip from one specimen onto another. FORD LABORATORY TEST METHOD BO 115-02 Page 2 of 2 Copyright 2001, Ford Global Technologies, Inc. Salt Spray Cabinet The salt spray cabinet and operating conditions must meet the requirements of ASTM B 117. Exterior Plasti

7、c Parts Expose exterior parts to five continuous cycles as detailed below. Interior Plastic Parts Expose interior parts to three continuous cycles as detailed below. Note: The number of cycles indicated must be used unless otherwise specified by the relevant Engineering Specification or drawing. Cyc

8、ling Test Each single cycle consists of the following: a) 4 hours in the fluorescent sunlamp cabinet. The test specimens must be 30 cm from the lamps. b) 4 hours in the salt spray cabinet. c) 16 hours in the humidity cabinet. Evaluation Examine and report any changes in appearance or other physical

9、properties occurring as a result of this test as required by the relevant Engineering Specification or drawing. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities.