ETSI TS 125 463-2004 Universal Mobile Telecommunications System (UMTS) UTRAN Iuant interface Remote Electrical Tilting (RET) antennas Application Part (RETAP) signalling《全球移动通信系统(U.pdf

《ETSI TS 125 463-2004 Universal Mobile Telecommunications System (UMTS) UTRAN Iuant interface Remote Electrical Tilting (RET) antennas Application Part (RETAP) signalling《全球移动通信系统(U.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 125 463-2004 Universal Mobile Telecommunications System (UMTS) UTRAN Iuant interface Remote Electrical Tilting (RET) antennas Application Part (RETAP) signalling《全球移动通信系统(U.pdf（47页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 125 463 V6.1.0 (2004-12)Technical Specification Universal Mobile Telecommunications System (UMTS);UTRAN Iuant interface: Remote Electrical Tilting (RET)antennas Application Part (RETAP) signalling(3GPP TS 25.463 version 6.1.0 Release 6)ETSI ETSI TS 125 463 V6.1.0 (2004-12) 1 3GPP TS 25.463

2、version 6.1.0 Release 6 Reference RTS/TSGR-0325463v610 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 780

3、3/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference vers

4、ion is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of sta

5、tus. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notifica

6、tion No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2004. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for

7、 the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 125 463 V6.1.0 (2004-12) 2 3GPP T

8、S 25.463 version 6.1.0 Release 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI S

9、R 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR

10、Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This

11、Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the corresponding

12、 ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp . ETSI ETSI TS 125 463 V6.1.0 (2004-12) 3 3GPP TS 25.463 version 6.1.0 Release 6 Contents Intellectual Property Rights2 Foreword.2 Foreword.5 1 Scope 6 2 Ref

13、erences 6 3 Definitions and abbreviations.6 3.1 Definitions6 3.2 Abbreviations .8 4 General .8 4.1 Procedure specification principles8 4.2 Forwards and backwards compatibility8 4.3 Multi-antenna units.8 4.4 Integer Representation8 5 Services expected from signalling transport.8 5.1 Elementary proced

14、ure format .9 5.1.1 Initiating message .9 5.1.2 Response message 9 6 Control elementary procedures 10 6.1 State Model 10 6.2 General procedure handling .10 6.2.1 Alarms 10 6.2.2 Procedure message interpretation .10 6.3 Overview of elementary procedures.11 6.4 Description of elementary procedures12 6

15、.5 Common elementary procedures14 6.5.1 Reset Software 14 6.5.2 Get Alarm Status.14 6.5.3 Get Information 15 6.5.4 Clear Active Alarms .16 6.5.5 Alarm Subscribe .17 6.5.6 Self Test18 6.5.7 Void 19 6.5.8 Void 19 6.5.9 Read User Data .19 6.5.10 Write User Data 19 6.5.11 Download Start .20 6.5.12 Downl

16、oad Application21 6.5.13 Download End 22 6.6 Single-antenna elementary procedures.23 6.6.1 Calibrate23 6.6.2 Send Configuration Data 23 6.6.3 Set Tilt 24 6.6.4 Get Tilt25 6.6.5 Alarm Indication.26 6.6.6 Set Device Data 27 6.6.7 Get Device Data28 6.7 Multi-antenna elementary procedures 28 6.7.1 Anten

17、na Calibrate .28 6.7.2 Antenna Set Tilt29 6.7.3 Antenna Get Tilt .30 6.7.4 Antenna Set Device Data31 6.7.5 Antenna Get Device Data .32 ETSI ETSI TS 125 463 V6.1.0 (2004-12) 4 3GPP TS 25.463 version 6.1.0 Release 6 6.7.6 Antenna Alarm Indication 33 6.7.7 Antenna Clear Active Alarms.34 6.7.8 Antenna G

18、et Alarm Status 34 6.7.9 Antenna Get Number Of Antennas.35 6.7.10 Antenna Send Configuration Data 36 7 Unknown elementary procedures.37 Annex A (normative): Return Codes for secondary devices 38 Annex B (normative): Assigned fields for additional data .40 Annex C (normative): Procedure sequence for

19、download of software to a secondary device.42 Annex D (informative): Overview of elementary procedures.43 Annex E (informative): Change history .45 History 46 ETSI ETSI TS 125 463 V6.1.0 (2004-12) 5 3GPP TS 25.463 version 6.1.0 Release 6 Foreword This Technical Specification has been produced by the

20、 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of rele

21、ase date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e.

22、technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 125 463 V6.1.0 (2004-12) 6 3GPP TS 25.463 version 6.1.0 Release 6 1 Scope The present document specifies the Remote Electrical Tilting

23、Application Part (RETAP) between the implementation specific O see annex A 2 i 1 octet Unsigned integer State flag i i = 1 N Description: The secondary device uses this procedure to report alarm state changes to the primary device. This procedure shall only be performed if the secondary has performe

24、d an AlarmSubscribe procedure since its latest reset. For each alarm, the current alarm state and alarm code shall be reported if and only if any change in its state has occurred during the period of time since the last reported state. An AlarmIndication procedure shall be performed if at least one

25、alarm shall be reported. The first AlarmIndication procedure after the AlarmSubscribe procedure shall report the active alarm states. ETSI ETSI TS 125 463 V6.1.0 (2004-12) 273GPP TS 25.463 version 6.1.0 Release 6 Alarm state changes are considered as reported at the time the message is passed to the

26、 transport layer. State flag = 0 represents alarm state cleared. State flag = 1 represents alarm state raised. 6.6.6 Set Device Data Table 6.6.6.1: Elementary procedure Set Device Data Name: SetDeviceData Code: 0x0E Issued by: Primary device Procedure class: 1 DownloadMode state: No Power mode: Low

27、Table 6.6.6.2: Initiating message parameters and format for Set Device Data Number Length Type Description 1 1 octet Unsigned integer Field number, see annex B 2 See annex B See annex B Data to write Table 6.6.6.3: Response message parameters and format for Set Device Data Number Length Type Descrip

28、tion 1 1 octet ReturnCode Return code OK Description: On receipt of the initiating message the secondary device should write the data given in the parameters of the initiating message into the fields optionally provided for configuration data and listed in annex B of this TS. If an attempt is made t

29、o write to fields which are designated as read only, the return code ReadOnly is returned and the data for those fields is ignored. If an attempt is made to write to fields which are not supported by the device the return code UnknownParameter is returned and the data for those fields is ignored. Ta

30、ble 6.6.6.4: Return codes for Set Device Data OK FAIL CommentFormatError Busy WorkingSoftwareMissing HardwareError ReadOnly UnknownParameter ETSI ETSI TS 125 463 V6.1.0 (2004-12) 283GPP TS 25.463 version 6.1.0 Release 6 6.6.7 Get Device Data Table 6.6.7.1: Elementary procedure Get Device Data Name:

31、GetDeviceData Code: 0x0F Issued by: Primary device Procedure class: 1 DownloadMode state: No Power mode: Low Table 6.6.7.2: Initiating message parameters and format for Get Device Data Number Length Type Description 1 1 octet Unsigned integer Field number; see annex B Table 6.6.7.3: Response message

32、 parameters and format for Get Device Data Number Length Type Description 1 1 octet ReturnCode Return code OK 2 See annex B See annex B Field value Description: In this procedure the secondary device shall return the data stored in the field for configuration data specified by the field number in th

33、e procedure and listed in annex B of this TS. Table 6.6.7.4: Return codes for Get Device Data OK FAIL CommentFormatError Busy WorkingSoftwareMissing UnknownParameter 6.7 Multi-antenna elementary procedures 6.7.1 Antenna Calibrate Table 6.7.1.1: Elementary procedure Antenna Calibrate Name: AntennaCal

34、ibrate Code: 0x80 Issued by: Primary device Procedure class: 1 DownloadMode state: No Power mode: High ETSI ETSI TS 125 463 V6.1.0 (2004-12) 293GPP TS 25.463 version 6.1.0 Release 6 Table 6.7.1.2: Initiating message parameters and format for Antenna Calibrate Number Length Type Description 1 1 octet

35、 Unsigned integer Antenna number Table 6.7.1.3: Response message parameters and format for Antenna Calibrate Number Length Type Description 1 1 octet Unsigned integer Antenna number 2 1 octet ReturnCode Return code OK Description: On receipt of the initiating message the secondary device shall perfo

36、rm a calibration of the antenna addressed by the antenna number. During calibration the actuator is driven through the whole tilt range of the antenna. The response time to this Antenna Calibrate procedure shall be less than 4 minutes. Table 6.7.1.4: Return codes for Antenna Calibrate OK FAIL Commen

37、tFormatError Busy HardwareError WorkingSoftwareMissing MotorJam ActuatorJam NotConfigured UnsupportedProcedure If the addressed antenna is not existing, FormatError is returned. 6.7.2 Antenna Set Tilt Table 6.7.2.1: Elementary procedure Antenna Set Tilt Name: AntennaSetTilt Code: 0x81 Issued by: Primary device Procedure class: 1 DownloadMode state: No Power mode: High Table 6.7.2.2: Initiating message parameters and format for Antenna Set Tilt Number Length Type Description 1 1 octet Signed integer Antenna number 2 2 octets Signed integer Tilt value