ETSI TS 101 804-3-2004 Methods for Testing and Specification (MTS) Conformance Test Specification for ITU-T H 225 0 (Terminal Gatekeeper and Gateway) Part 3 Abstract Test Suite (AT_1.pdf

《ETSI TS 101 804-3-2004 Methods for Testing and Specification (MTS) Conformance Test Specification for ITU-T H 225 0 (Terminal Gatekeeper and Gateway) Part 3 Abstract Test Suite (AT_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 101 804-3-2004 Methods for Testing and Specification (MTS) Conformance Test Specification for ITU-T H 225 0 (Terminal Gatekeeper and Gateway) Part 3 Abstract Test Suite (AT_1.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 101 804-3 V2.1.1 (2004-11)Technical Specification Methods for Testing and Specification (MTS);Conformance Test Specification for ITU-T H.225.0(Terminal, Gatekeeper and Gateway);Part 3: Abstract Test Suite (ATS) and partial ProtocolImplementation eXtra Information for Testing (PIXIT) proform

2、afloppy3 ETSI ETSI TS 101 804-3 V2.1.1 (2004-11) 2 Reference RTS/MTS-00095-3 Keywords ATS, gatekeeper, gateway, H.323, IP, PIXIT, supplementary service, terminal, testing, TTCN, VoIP ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Si

3、ret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version

4、or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secret

5、ariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send

6、 your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications St

7、andards Institute 2004. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for

8、the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 101 804-3 V2.1.1 (2004-11) 3 Contents Intellectual Property Rights5 Foreword.5 1 Scope 6 2 References 6 3 Definitions and abbreviations.7 3.1 Definitions7 3.2 Abbreviations .7 4 Abstract test method.8 5 ATS conventions8

9、 5.1 Version of TTCN used .8 6 ATS to TP map.8 7 PCTR conformance 8 8 PIXIT conformance9 9 ATS conformance 9 Annex A (normative): Protocol Conformance Test Report (PCTR) proforma10 A.1 Identification summary.10 A.1.1 Protocol conformance test report10 A.1.2 IUT identification.10 A.1.3 Testing enviro

10、nment.10 A.1.4 Limits and reservations 11 A.1.5 Comments.11 A.2 IUT conformance status .11 A.3 Static conformance summary .11 A.4 Dynamic conformance summary11 A.5 Static conformance review report.12 A.6 Test campaign report12 A.7 Observations.20 Annex B (normative): Partial PIXIT proforma 21 B.1 Id

11、entification summary.21 B.2 Abstract Test Suite summary .21 B.3 Test laboratory21 B.4 Client (of the test laboratory) .22 B.5 System Under Test (SUT) 22 B.6 Protocol information.23 B.6.1 Protocol identification 23 B.6.2 Parameters for RAS testing 23 B.6.2.1 IP port and address information23 B.6.2.2

12、Addresses and identifiers 23 B.6.2.3 Bandwidth information.24 B.6.2.4 RAS timers24 B.6.2.5 RAS configuration details.25 ETSI ETSI TS 101 804-3 V2.1.1 (2004-11) 4 B.6.3 Parameters for basic call control testing.25 B.6.3.1 Basic call control configuration details.25 B.6.3.2 Information element values.

13、26 B.6.3.3 UUIE parameter values.26 B.6.4 Test management timers.27 Annex C (normative): Abstract Test Suite (ATS) .28 C.1 The TTCN Graphical form (TTCN.GR) 28 C.2 The TTCN Machine Processable form (TTCN.MP)28 Annex D (informative): Bibliography.29 History 30 ETSI ETSI TS 101 804-3 V2.1.1 (2004-11)

14、5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Proper

15、ty Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, inclu

16、ding IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) ha

17、s been produced by ETSI Technical Committee Methods for Testing and Specification (MTS). The present document is part 3 of a multi-part deliverable covering the H.225.0 protocol for Terminal, Gatekeeper and Gateway as identified below: Part 1: “Protocol Implementation Conformance Statement (PICS) pr

18、oforma“; Part 2: “Test Suite Structure and Test Purposes (TSS Part 3: “Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT) proforma“. ETSI ETSI TS 101 804-3 V2.1.1 (2004-11) 6 1 Scope The present document specifies the Abstract Test Suite (ATS) and par

19、tial Protocol Implementation eXtra Information for Testing (PIXIT) proforma for the H.225.0 protocol for Terminal, Gatekeeper and Gateway. The objective of the present document is to provide conformance tests that give a greater probability of inter-operability. The ATS Conformance Test Specificatio

20、n for ITU-T H.225.0 (Terminal, Gatekeeper and Gateway); Part 1: Protocol Implementation Conformance Statement (PICS) proforma“. 2 Void. 3 ITU-T Recommendation H.323 (2000): “Framework and wire-protocol for multiplexed call signalling transport“. 4 ITU-T Recommendation H.225.0 (2000): “Call signallin

21、g protocols and media stream packetization for packet-based multimedia communication systems“. 5 ITU-T Recommendation Q.931: “ISDN user-network interface layer 3 specification for basic call control“. 6 ISO/IEC 9646-1: “Information technology - Open Systems Interconnection - Conformance testing meth

22、odology and framework - Part 1: General concepts“. 7 ISO/IEC 9646-2: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 2: Abstract Test Suite specification“. 8 ISO/IEC 9646-3: “Information technology - Open Systems Interconnection - Conform

23、ance testing methodology and framework - Part 3: The Tree and Tabular Combined Notation (TTCN)“. 9 ISO/IEC 9646-4: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 4: Test realization“. 10 ISO/IEC 9646-5: “Information technology - Open Sys

24、tems Interconnection - Conformance testing methodology and framework - Part 5: Requirements on test laboratories and clients for the conformance assessment process“. 11 ETSI TR 101 666: “Information technology; Open Systems Interconnection Conformance testing methodology and framework; The Tree and

25、Tabular Combined Notation (TTCN) (Ed. 2+)“. 12 ITU-T Recommendation E.164: “The international public telecommunication numbering plan“. ETSI ETSI TS 101 804-3 V2.1.1 (2004-11) 7 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given

26、in ITU-T Recommendation H.323 3, ITU-T Recommendation H.225.0 4, ISO/IEC 9646-1 6, ISO/IEC 9646-2 7, ISO/IEC 9646-3 8 and the following apply: Basic Call Control (BCC): signalling protocol associated with the DSS1 - ISDN Basic Call control procedures of ITU-T Recommendation Q.931 inopportune: test p

27、urpose covering a signalling procedure where an inopportune message (type of message not expected in the IUT current state) is sent to the IUT syntactically invalid: test purpose covering a signalling procedure where a valid (expected in the current status of the IUT) but not correctly encoded (unkn

28、own or incorrect parameter values) message is sent to the IUT, which shall react correctly and eventually reject the message valid: test purpose covering a signalling procedure where all the messages sent to or received from the IUT are valid (expected in the current status of the IUT) and correctly

29、 encoded 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ARQ Admission ReQuest ATS Abstract Test Suite BCC Basic Call Control BRQ Bandwidth ReQuestDGK Destination GateKeeper DRQ Disengage ReQuest DSS1 Digital Signalling System 1 ETS Executable Test Suit

30、e GK GateKeeper GRQ Gatekeeper ReQuest I Inopportune IP Internet ProtocolIRQ Information ReQuest IRR Information Request Response ISDN Integrated Services Digital Network IUT Implementation Under Test LRQ Location ReQuest MOT Mean Of Testing MTC Main Test Component PCO Point of Control and Observati

31、on PCTR Protocol Conformance Test Report PICS Protocol Implementation Conformance Statement PIXIT Protocol Implementation eXtra Information for Testing PTC Parallel Test Component RAS Registration, Admission and Status RRQ Registration ReQuest S Syntactically invalid SUT System Under Test TCP Transm

32、ission Control Protocol TE TErminalTP Test Purpose TSS Test Suite Structure TTCN Testing and Test Control Notation UDP User Datagram Protocol URQ Unregister ReQuest ETSI ETSI TS 101 804-3 V2.1.1 (2004-11) 8 UUIE User-User Information Element 4 Abstract test method The remote test method is applied f

33、or this ATS. Tester H.225.0 RAS part H.225.0 call signalling part PCO T IUT L4 UDP TCP UDP/TCP L3 Network layer: IP IP L2 Link layer Link layer L1 Physical layer Physical layer Service provider Figure 1: Remote test method with PCO T A Point of Control and Observation (PCO) resides between the layer

34、 4 and the tester, which executes the signalling procedures corresponding to the test case dynamic behaviour. This PCO is named “T“ because it is located above the transport layer. The L PCO is used to control and observe the behaviour of the Implementation Under Test (IUT) using the layers of the S

35、ervice provider. 5 ATS conventions 5.1 Version of TTCN used The version of TTCN used is that defined in TR 101 666 11. 6 ATS to TP map The identifiers used for the TPs are reused as test case names. Thus there is a straightforward one-to-one mapping. 7 PCTR conformance A test laboratory, when reques

36、ted by a client to produce a PCTR, is required, as specified in ISO/IEC 9646-5 10, to produce a PCTR conformant with the PCTR template given in annex B of ISO/IEC 9646-5 10. Furthermore, a test laboratory, offering testing for the ATS specification contained in annex C, when requested by a client to

37、 produce a PCTR, is required to produce a PCTR conformant with the PCTR proforma contained in annex A. A PCTR which conforms to this PCTR proforma specification shall preserve the content and ordering of the clauses contained in annex A. Clause A.6 of the PCTR may contain additional columns. If incl

38、uded, these shall be placed to the right of the existing columns. Text in italics may be retained by the test laboratory. ETSI ETSI TS 101 804-3 V2.1.1 (2004-11) 9 8 PIXIT conformance A test realizer, producing an executable test suite for the ATS specification contained in annex C, is required, as

39、specified in ISO/IEC 9646-4 9, to produce an augmented partial PIXIT proforma conformant with this partial PIXIT proforma specification. An augmented partial PIXIT proforma which conforms to this partial PIXIT proforma specification shall, as a minimum, have contents which are technically equivalent

40、 to annex B. The augmented partial PIXIT proforma may contain additional questions that need to be answered in order to prepare the Means Of Testing (MOT) for a particular IUT. A test laboratory, offering testing for the ATS specification contained in annex C, is required, as specified in ISO/IEC 96

41、46-5 10, to further augment the augmented partial PIXIT proforma to produce a PIXIT proforma conformant with this partial PIXIT proforma specification. A PIXIT proforma which conforms to this partial PIXIT proforma specification shall, as a minimum, have contents which are technically equivalent to

42、annex B. The PIXIT proforma may contain additional questions that need to be answered in order to prepare the test laboratory for a particular IUT. 9 ATS conformance The test realizer, producing MOT and ETS for this ATS specification, shall comply with the requirements of ISO/IEC 9646-4 9. In partic

43、ular, these concern the realization of an ETS based on each ATS. The test realizer shall provide a statement of conformance of the MOT to this ATS specification. An ETS which conforms to this ATS specification shall contain test groups and test cases which are technically equivalent to those contain

44、ed in the ATS in annex C. All sequences of test events comprising an abstract test case shall be capable of being realized in the executable test case. Any further checking which the test system might be capable of performing is outside the scope of this ATS specification and shall not contribute to

45、 the verdict assignment for each test case. Test laboratories running conformance test services using this ATS shall comply with ISO/IEC 9646-5 10. A test laboratory which claims to conform to this ATS specification shall use an MOT which conforms to this ATS. ETSI ETSI TS 101 804-3 V2.1.1 (2004-11)

46、 10Annex A (normative): Protocol Conformance Test Report (PCTR) proforma Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that users of the present document may freely reproduce the PCTR proforma in this annex so that it can be used for

47、its intended purposes and may further publish the completed PCTR. A.1 Identification summary A.1.1 Protocol conformance test report PCTR number: PCTR date: Corresponding SCTR number: Corresponding SCTR date: Test laboratory identification: Test laboratory manager: Signature: A.1.2 IUT identification

48、 Name: Version: Protocol specification: ITU-T Recommendation H.225.0 4 PICS: Previous PCTRs (if any): A.1.3 Testing environment PIXIT reference number: ATS specification: TS 101 804-3 Abstract test method: Multi-party test method (see ISO/IEC 9646-2 7) Means of testing identification: Dates of testi

49、ng: Conformance log reference(s): Retention date for log reference(s): ETSI ETSI TS 101 804-3 V2.1.1 (2004-11) 11A.1.4 Limits and reservations Additional information relevant to the technical contents or further use of the test report, or to the rights and obligations of the test laboratory and the client, may be given here. Such information may include restriction on the publication of the report. . . . . A.1.5 Comments Additional comments may be given by either the client or the test laboratory on any of the contents of the PC