ETSI ETS 300 460-1996 Satellite Earth Stations and Systems (SES) Maritime Mobile Earth Stations (MMESs) Operating in the 1 5 1 6 GHz Bands Providing Low Bit Rate Data Communication_1.pdf

《ETSI ETS 300 460-1996 Satellite Earth Stations and Systems (SES) Maritime Mobile Earth Stations (MMESs) Operating in the 1 5 1 6 GHz Bands Providing Low Bit Rate Data Communication_1.pdf》由会员分享，可在线阅读，更多相关《ETSI ETS 300 460-1996 Satellite Earth Stations and Systems (SES) Maritime Mobile Earth Stations (MMESs) Operating in the 1 5 1 6 GHz Bands Providing Low Bit Rate Data Communication_1.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、* ETSI ETS*300*460 b 3400855 0305285 900 W ETS 300 460 May 1996 Source: ETSI TC-SES Reference: DE/SES-05011 ICs: 33.060.50 Key words: maritime, satellite, mobile, earth station, MES, MMES, emergency, LBRDC, GMDSS, INMARSAT-C Satellite Earth Stations and Systems (SES); Maritime Mobile Earth Stations

2、(MMESs) operating in the 1 ,!YI ,6 GHz bands providing Low Bit Rate Data Communications (LBRDCs) for the Global Maritime Distress and Safety System (GMDSS); Technical characteristics and methods of measurement ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: F-O6

3、921 Sophia Antipolis CEDEX - FRANCE ffice address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE X.400: c=fr, a=atlas, p=etsi, $=secretariat - Internet: secretariat etsi.fr Tel.: +33 92 94 42 O0 - Fax: +33 93 65 47 16 Copyright Notification: No part may be reproduced except as author

4、ized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. Q European Telecommunications Standards Institute 1996. All rights reserved. Page 2 ETSI ETS*300*4b0 96 3400855 Ol10528b 847 ETS 300 460: May 1996 Whilst every care has been taken in the prep

5、aration and publication of this document, errors in content, typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to “ETSI Editing and Committee Support Dept.“ at the address shown on the title page. i 3 Foreword . 5 1 2 3 4 5 6 7 8 9 r Page 3 ETS 3 00 46

6、0: May 1996 ETSI ETS*300*460 96 H 3400855 0305287 i83 Contents Scope 7 Normative references 8 Definitions and abbreviations 9 3.1 Definitions 9 3.2 Abbreviations . 10 Tests 10 4.1 4.2 Test report . 10 Special Test Equipment (STE) 10 Environmental tests . 11 General requirements . 11 6.1 Equipment ce

7、rtification 11 6.2 Power supply 11 Power supply reversal . 11 Power supply interruption 12 6.3 Mechanical construction 12 6.4 Electrical safety 13 6.5 6.6 Additional facilities . 14 6.7 Integrity of GMDSS equipment 14 6.8 Operating controls 14 6.9 User documentation . 15 6.1 O Equipment labelling 15

8、 6.1 1 Ship earth station identities 16 6.12 Storage of sohare 16 6.1 3 Equipment maintenance 16 6.2.1 6.2.2 Radio frequency radiation protection (classes 1, 2 and 3 only) . 13 Operational requirements 17 7.1 7.2 7.3 Navigational interface 18 7.4 Provision for initiating distress alerts from two pos

9、itions (classes 1. 2 and 3 only) . 18 Printing of Enhanced Group Call (EGC) messages (classes O. 2 and 3 only) . 17 Service codes (classes O. 2 and 3 only) 17 Unwanted emissions . 19 8.1 General 19 8.2 Unwanted emissions outside the band 1 626, 5 to 1 645, 5 MHz 19 8.3 Unwanted emissions within the

10、1 6265 to 1 6455 MHz band (classes 1, 2 and 3 only) 20 Ship earth station Control and Monitoring Functions (CMF) . 21 9.1 General 21 9.2 Processor monitoring (classes 1 . 2 and 3 only) . 21 9.3 9.4 Initial burst rate transmission (classes 1. 2 and 3 only) . 22 9.5 9.6 Network control reception (clas

11、ses 1 . 2 and 3 only) 22 Transmit frequency sub-system (classes 1. 2 and 3 only) . 21 Network control authorisation (classes 1 . 2 and 3 only) 22 Annex A (normative): Environmental tests 24 A.l Ambient temperature . 24 i ETSI ETS*300*460 96 3400855 01105288 bLT Page 4 ETS 300 460: May 1996 A.2 Relat

12、ive humidity . 24 A.3 Vibration 25 Annex B (normative): Unwanted emissions above 1 GHz - test procedure . 26 B.l Introduction . 26 6.2 Measuring apparatus 26 8.3 Test Set-up 26 8.4 Measuring procedure 26 8.5 Altemative measurement procedure 27 Annex C (informative): Manufacturers declaration . 28 Hi

13、story . 29 Page 5 ETS 300 460: May 1996 ETSI ETS*300*460 96 U 31-lLl0855 0305289 556 Foreword This European Telecommunication Standard (ETS) has been produced by the Satellite Earth Stations and Systems (SES) Technical Committee of the European Telecommunications Standards Institute (ETSI). Transpos

14、ition dates Date of adoption of this ETS: Date of latest announcement of this ETS (doa): 26 April 1996 31 August 1996 Date of latest publication of new National Standard or endorsement of this ETS (dop/e): 29 February 1997 I Date of withdrawal of any conflicting National Standard (dow): 29 February

15、1997 Every ETS prepared by ETSI is a voluntary standard. This ETS may contain text concerning conformance testing of the equipment to which it relates. This text should be considered as guidance only and does not make this ETS mandatory. ETSI ETS*300*460 b = 34Q0855 0305290 278 Page 6 ETS 300 460: M

16、ay 1996 Blank page ETSI ETS*300*4bO b 3400855 OL0529L LO4 = Page 7 ETS 300 460: May 1996 1 Scope This European Telecommunication Standard (ETS) sets out the minimum performance requirements and technical characteristics for ship earth stations capable of transmitting and receiving direct-printing co

17、mmunications, and for Enhanced Group Call (EGC) equipment, as required by regulations IVn, IV/8, IV/9 and IWO of the 1974 International Convention for Safety of Life at Sea (COLAS) 5 as amended, concerning radio communications for the Global Maritime Distress and Safety System (GMDSS). Minimum perfo

18、rmance requirements for the Network Control Facility (NCF) are contained in ETS 300 459 131. NOTE: The only satellite system accepted by the SOLAS convention to provide LBRDC in the GMDSS is INMARSAT-C at the date of publication. For the purpose of this ETS the term “ship earth station“ is used in o

19、rder to align this ETS to ITU terminology. It is defined as a Maritime Mobile Earth Station (MMES) operating in the GMDSS. This ETS is applicable to the following classes of equipment: - Class O: - a stand alone EGC receiver; - Class 1: - a basic ship earth station providing shore-to-ship and ship-t

20、o-shore message transfer only; - Class2: - as for Class 1 but with EGC as an alternative to shore-to-ship transfer using a shared receiver; - Class 3: - as for Class 1 but with EGC using an independent receiver. This ETS covers equipment construction and performance testing. GMDSS requirements and t

21、ests are included where they are supplementary to those contained in the equipment certification required in subclause 5.1. Frequency bands allocated by the Radio Regulations l to the MariMme Mobile Satellite Service (MMSS) are as follows: Requirements are specified in order to ensure the requiremen

22、ts of the GMDSS are met, to protect other users of the frequency spectrum from unacceptable interference, for the purposes of general safety and for the provision of protection of the ship earth station against electromagnetic interference from other systems. 3 Page 8 ETS 300 460: May 1996 ETSI ETS*

23、300*460 96 9 3400855 0105292 040 9 3 2 Normative references This ETS incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent

24、 amendments to or revisions of any of these publications apply to this ETS only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. I i11 International Telecommunication Union, Radio Regulations, (WARC 1992). I31 t41 151

25、 (71 181 191 IEC 510-2-1 (1978): “Methods of measurement for radio equipment used in satellite earth stations, Part 2: Measurement for sub-systems“. ETS 300 459: “Satellite Earth Stations and Systems (SES); Network Control Facilities (NCF) for Maritime Mobile Earth Stations (MMESs) operating in the

26、1,5/1,6 GHz and 11/12/14 GHz bands providing Low Bit Rate Data Communications (LBRDCs)“. CISPR 16-1 (First edition 1993-08): “Specification for radio disturbance and immunity measuring apparatus methods. Part 1: Radio disturbance and immunity measuring apparatus“. Regulations IVn, IV/8, IV/9 and IV/

27、10 of the 1988 Amendments to the 1974 SOLAS convention as amended. NMEA O1 83, version 2.01 : “Standards for Interfacing Marine Electronic Devices“. IMO Resolution A.663(16): “Performance Standards for INMARSAT Standard4 Ship Earth Stations Capable of Transmitting and Receiving Direct-Printing Commu

28、nications“. IMO Resolution A.664( 16): “Performance Standards for Enhanced Group Call Equipment“. IMO Resolution A.694(17): “General Requirements for Ship borne Radio Equipment forming part of the Global Maritime Distress and Safety System (GMDSS) and for Electronic Navigational Aids“. ISO/R694 (1 9

29、68): “Recommendations for the positioning of compasses, Method 6“. EN 55022 (1994): “Limits and methods of measurements of radio disturbance characteristics of information technology equipment“. ETSI ETS830084bO 96 3400855 0105293 T87 Page 9 ETS 300 460: May 1996 I 3 Definitions and abbreviations 3.

30、1 Definitions For the purposes of this ETS, the following definitions apply: ship earth station: A MMES on board a ship, (see clause 1). nominated bandwidth: The nominated bandwidth encompasses all spectral elements of the transmission which have a level greater than the specified spurious levels. T

31、he nominated bandwidth is wide enough to take account of the transmit carrier frequency stability. The nominated bandwidth is within the MMSS transmit frequency band within which the ship earth station operates. The bandwidth of the ship earth station radio frequency transmission is nominated by the

32、 manufacturer and included in the data sheet of the test report. unwanted emissions: For the purpose of this ETS unwanted emissions are those falling outside the nominated bandwidth. performance check: A performance check consists of the following: - for Class O equipment: - reception of a distress

33、priority EGC message; - for Class 1 equipment: - for Class 2 and 3 equipment: - transmission of a distress message; - transmission of a distress message and reception of a distress priority EGC message. The transmission of a distress message is considered to be successful when: - the Special Test Eq

34、uipment (STE) has received the distress message and correctly interpreted it; and the Equipment Under Test (EUT) has correctly indicated to the user, the acknowledgement of receipt of the transmission from the STE. The reception of a distress priority EGC message is considered to be successful when

35、the EUT has printed the message and the appropriate indications are provided to the user that a distress priority EGC message has been received. Special Test Equipment (STE): Specific equipment which enables the tests specified in this ETS to be carried out. Equipment Under Test (EUT): For the purpo

36、ses of this ETS the EUT includes all units necessary for intended operation. This includes: - - - the Externally Mounted Equipment (EME); the Internally Mounted Equipment (IME) including the data terminal equipment such as keyboard, Visual Display Unit (VDU), printer, etc.; all interconnecting cable

37、s and power supply leads. - ETSI ETS*300*460 %b 3Y001%55 0105294 913 Page 10 ETS 300 460: May 1996 I 3.2 Abbreviations For the purposes of this ETS, the following abbreviations apply: CMF EGC EIRP EMC EME EUT FARI GMDSS IME IMO MMSS NCF MMSI RF SOLAS STE VDU Control and Monitoring Function Enhanced

38、Group Call Equivalent Isotropically Radiated Power Electro-Magnetic Compatibility Externally Mounted Equipment Equipment Under Test Forward And Return Identity Global Maritime Distress and Safety System Internally Mounted Equipment International Maritime Organisation Maritime Mobile Satellite Servic

39、e Network Control Facility Maritime Mobile Service Identity Radio Frequency Safety Of Life At Sea Special Test Equipment Visual Display Unit 4 Tests 4.1 Special Test Equipment (STE) The STE shall be supplied by the manufacturer or system provider. Since this test equipment will be specific for the p

40、articular system, it is not possible to provide detailed specifications in this ETS. However, the following baseline is provided: - special test arrangements are required to simulate the satellite signal, thus enabling the ship earth station to transmit, to allow measurement of transmission paramete

41、rs; - any specification of these special test arrangements which may have direct or indirect effects on any specification of this ETS shall be clearly stated by the manufacturer; - the STE shall prevent any radiation of signals, and it shall be certified by the system operator to be suitable for suc

42、h purpose; - when using STE it shall be ensured that no transmission to the satellite occurs. 4.2 Test report The test report shall contain: - the value of the nominated bandwidth declared by the manufacturer; - the results of the test; - all parameters and operational conditions. Page 11 ETS 300 46

43、0: May 1996 ETSI ETS*300*4b0 9b m 3408855 0305295 85T 5 Environmental tests Purpose: To ensure that the equipment is capable of continuous operation under conditions of various sea states, vibration, humidity and temperature likely to be experienced in ships. Specif ication: Elements of the equipmen

44、t shall be divided into two categories as follows, marked to indicate the class for which it is intended: - IME: equipment or units designed to be protected from the weather; - EME: equipment or units intended to be exposed to the weather. The equipment shatl be subjected to the tests specified in a

45、nnex A. These tests shall be carried out before any other test specified in this ETS. The manufacturer shall declare to which category each of the elements of the equipment belongs. Verification: The equipment shall successfully complete the performance checks under the conditions, defined in annex

46、A. 6 General requirements 6.1 Equipment certification Purpose: To ensure that the ship earth station has obtained certification for operating in the satellite system to be used for communications in the GMDSS. Specification : The ship earth station shall have obtained certification for operating in

47、the satellite system to be used for communications in the GMDSS as required by IMO Resolution A.663(16) 7, section 2 or IMO Resolution A.664(16) 8, section 2. Verification: By documentary evidence. 6.2 Power supply 6.2.1 Power supply reversal Purpose: To ensure that the equipment is protected from t

48、he effects of reversal of the power supply polarity. Specification: Means shall be incorporated for the protection of equipment from reversal of the power supply polarity. ETSI ETS*300*460 96 3400855 0305296 796 m I Page 12 ETS 300 460: May 1996 Verif ication: The ship earth station shall be connect

49、ed to a power supply of reversed polarity at nominal voltage. If a protection fuse blows during this test it shall be replaced. Normal power supply polarity shall then be restored and a performance check carried out successfully. 6.2.2 Power supply interruption Purpose: To ensure satisfactory operation after power supply interruption. Specification : Any interruption of the power supply of up to 60 seconds duration shall not require the equipment to be manually re-initialised and shall not result in change or loss of stored operational parameters or in loss of stored messa