ETSI ETS 300 329-1997 Radio Equipment and Systems (RES) ElectroMagnetic Compatibility (EMC) for Digital Enhanced Cordless Telecommunications (DECT) Equipment (Second Edition)《无线电设备_1.pdf

《ETSI ETS 300 329-1997 Radio Equipment and Systems (RES) ElectroMagnetic Compatibility (EMC) for Digital Enhanced Cordless Telecommunications (DECT) Equipment (Second Edition)《无线电设备_1.pdf》由会员分享，可在线阅读，更多相关《ETSI ETS 300 329-1997 Radio Equipment and Systems (RES) ElectroMagnetic Compatibility (EMC) for Digital Enhanced Cordless Telecommunications (DECT) Equipment (Second Edition)《无线电设备_1.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、 STD-ETSI ETS 300 327-ENGL 1777 M 3900855 020723b 755 STAN DARD ETS 300 329 June 1997 Second Edition Source: ETSI TC-RES Reference: RE/RES-09036 ICs: 33.020 Key words: DECT, EMC, radio, testing Radio Equipment and Systems (RES); ElectroMagnetic Compatibility (EMC) for Digital Enhanced Cordless Telec

2、ommunications (DECT) equipment ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: F-O6921 Sophia Antipolis CEDEX - FRANCE ffice address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE X.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretaria

3、t etsi.fr Tel .: +33 4 92 94 42 O0 - Fax: +33 4 93 65 47 16 Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. O European Telecommunications Standards Institute 1997. All right

4、s reserved. STD-ETSI ETS 300 327-ENGL 1997 3400855 0207237 771 Page 2 ETS 300 329: June 1997 Whilst every care has been taken in the preparation and publication of this document, errors in content, typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to “

5、ETSI Editing and Committee Support Dept.“ at the address shown on the title page. STD-ETSI ETS 300 327-ENGL 1997 3400855 0207238 828 H Page 3 ETS 300 329: June 1997 Contents Foreword . .- 5 Scope . 7 Normative references 7 Definitions and abbreviations . 8 Definit ions ._ _. 8 3.1 3.2 Abbreviations

6、. ._ 9 General test conditions 9 Arrangements for test signals at the input of the transceiver 10 Loop back data. . 4.2.2 Speech equipment 10 Connection of test signais for transceivers . -10 4.1 Test conditions . 9 4.2 4.2.1 10 Normal test modulation . 10 4.4.1 RF connection . 10 Connection of test

7、 signals for receiver-only equipment . 10 4.5.1 RF connection . 10 Narrow band responses on receivers or receivers which are part of transceivers 11 4.3 4.4 4.5 4.6 4.7 Receiver test signal level . 1.1 Performance assessment . 11 5.2 Equipment classification . 12 5.1 General . 11 5.3 Ancillary equip

8、ment 12 5.4 Assessment of host connected equipment and plug-in cards . 12 5.4.1 Alternative A: composite equipment. . 12 5.4.2 Alternative B: use of a test jig and three hosts 12 Performance assessment test procedure to verify no loss of user control functions or stored data for DECT transceivers 13

9、 Performance assessment of audio breakthrough 13 . 5.5 5.6 Performance criteria . . 15 6.1 6.2 6.3 6.4 Performance criteria for Continuous phenomena applied to DECT Transceivers (CT) 15 Performance criteria for Transient phenomena applied to DECT Transceivers (TT) 15 Performance criteria for Continu

10、ous phenomena applied to DECT Receive-only equipment (CR) . 15 Performance criteria for Transient phenomena applied to DECT Receive-only equipment (TR) 16 Applicability overview tables. . 16 7.1 Emission 16 7.2 Immunity ._._._ . 17 Test methods and limits for emission tests of transceivers and/or re

11、ceivers and/or ancillary 8.1 Test configuration 17 8.2 equipment . 17 Enclosure. ancillary equipment tested in isolation . 18 8.2.1 Definition . 18 8.2.2 Test method 18 8.2.3 Test limit 18 DC power input/output port 18 8.3.1 Definition . 18 8.3.2 Test method 19 8.3 STD*ETSI ETS 300 327-ENGL L797 340

12、0855 0207237 7bi Page 4 ETS 300 329: June 1997 8.3.3 Test limit . 19 AC mains power input/output pori . 19 8.4.1 Definition . 19 8.4.2 Test method 19 8.4.3 Test limit . 19 8.4 9 Test methods for immunity tests of transceivers and/or receivers and/or ancillary equipment 20 9.1 9.2 9.3 9.4 9.5 9.6 9.7

13、 9.8 Test configuration 20 Radio frequency electromagnetic field (80 - 1 O00 MHz) 20 9.2.1 Definition . 20 9.2.2 9.2.3 Performance criteria . 21 Electrostatic discharge . 21 9.3.1 Definition . 21 9.3.2 Test method and levels . 21 9.3.3 Performance criteria . 21 Fast transients common mode 22 9.4.1 D

14、efinition . 22 9.4.2 Test method and levels . 22 9.4.3 Performance criteria . 22 RF common mode, O, 15 MHz - 80 MHz 22 9.5.1 Definition . 23 9.5.3 Performance criteria . 23 Transients and surges, vehicular environment . 23 9.6.1 Definition . 24 9.6.2 Test method and level 24 9.6.3 Performance criter

15、ia . 25 Voltage dips and interruptions . 25 9.7.1 Definition . 25 9.7.2 Test method and levels . 25 9.7.3 Performance criteria . 25 Surges, common and differential mode 26 9.8.1 Definition . 26 9.8.2 Test method and levels . 26 9.8.3 Performance criteria . 27 Test method and level 21 9.5.2 Test meth

16、od and level 23 Annex A (normative): Subclauses of this ETS relevant for compliance with the essential requirements of the EC Council Directives 28 History 29 STD-ETSI ETS 300 327-ENGL 1777 M 3400855 0207240 48b Page 5 ETS 300 329: June 1997 Foreword This European Telecommunication Standard (ETS) ha

17、s been produced by the European Telecommunications Standards Institute (ETSI) in response to a mandate from the European Commission issued under Council Directive 83/189/EEC (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. Thi

18、s ETC is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities referencing the Council Directive on the approximation of the laws of the Member States relating to electromagnetic compatibility (“the EMC Directive“) (89/

19、336/EEC as amended). Technical specifications relevant to the EMC Directive are given in annex A. This ETS is based on the considerations and guidance given in ETR 238. Transposition dates Date of adoption: Date of latest announcement of this ETS (doa): 6 June 1997 30 September 1997 Date of latest p

20、ublication of new National Standard or endorsement of this ETS (dop/e): 31 March 1998 I 1 Date of withdrawal of any conflicting National Standard (dow): 31 March 1998 STD-ETSI ETS 300 327-ENGL 1977 M 3400855 020724L 312 M Page 7 ETS 300 329: June 1997 1 scope This European Telecommunication Standard

21、 (ETS) covers the assessment of radio communication and ancillary equipment in respect of ElectroMagnetic Compatibility (EMC). This ETS specifies the minimum performance and the methods of measurements of EMC on Digital Enhanced Cordless Telecommunications (DECT) radio and ancillary equipment. This

22、ETS specifies the applicable EMC tests, the limits, and the performance criteria for digital radio equipment as described in ETS 300 175-2 4 and I-ETS 300 176 5, operating in the frequency range 1 880 to 1 900 MHz, and for the associated ancillary equipment. The environment classification used in th

23、is ETS refers to the environment classification used in the Generic Standards EN 50081-1 l and EN 50082-1 2, except the vehicular environment class which refers to IS0 7637 6, 7. The EMC requirements have been selected to ensure an adequate level of compatibility for apparatus at residential, commer

24、cial, light industrial and vehicular environments. The levels, however, do not cover extreme cases which may occur in any location but with a low probability of occurrence. This ETS may not cover those cases where a potential source of interference, which is producing individually repeated transient

25、 phenomena, or a continuous phenomena, is permanently present, e.g. a radar or broadcast site in the near vicinity. In such a case it may be necessary to use special protection applied to either the source of interference, or the interfered part, or both. Compliance of radio equipment to the require

26、ments of this ETS does not signify compliance to any requirement related to the use of the equipment (.e. licensing requirements). Compliance to this ETS does not signify compliance to any safety requirements. However, it is the responsibility of the assessor of the equipment that any observation re

27、garding the equipment becoming dangerous or unsafe as a result of the application of the tests of this ETS, should be recorded in the test report. 2 Normat ive references This ETS incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at

28、 the appropriate places in the text and the publications listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this ETS only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication r

29、eferred to applies. PI 31 141 EN 50081-1 (1 992): “Electromagnetic compatibility - Generic emission standard. Part 1: Residential, commercial and light industry“. EN 50082-1 (1 992): “Electromagnetic compatibility - Generic immunity standard. Part 1 : Residential, commercial and light industry“. 89/

30、336/EEC: “Council Directive on the approximation of the laws of the Member States relating to electromagnetic compatibility“. ETS 300 175-2 (1993): “Radio Equipment and Systems (RES) - Digital European Cordless Telecommunications (DECT) Common interface Part 2: Physical layer“. I-ETS 300 176: “Radio

31、 Equipment and Systems (RES) - Digital European Cordless Telecommunications (DECT) Approval test specification“. IS0 7637-1 (1990): “Road vehicles - Electrical disturbance by conduction and coupling - Part 1: Passenger cars and light commercial vehicles with nominal 12 V supply voltage - Electrical

32、transient conduction along supply lines only“. Previous page is blank STD-ETSI ETS 300 327-ENGL 1797 3q00855 02072q2 257 Page 8 ETS 300 329: June 1997 i71 91 11 41 i 51 IS0 7637-2 (1 990): “Road vehicles - Electrical disturbance by conduction and coupling - Part 2: Commercial vehicles with nominal 2

33、4 V supply voltage - Electrical transient conduction along supply lines only“. ETS 300 175-3: “Radio Equipment and Systems (RES); Digital Enhanced Cordless Telecommunications (DECT); Common Interface (Ci); Part 3: Medium Access Control (MAC) layer“. ITU-T Recommendation 0.153 (1988): “Basic paramete

34、rs for the measurement of error performance at bit rates below the primary rate“. EN 55022 (1994): “Limits and methods of measurement of radio disturbance characteristics of information technology equipment“. CISPR 16-1 (1993): “Specification for radio disturbance and immunity measuring apparatus an

35、d methods - Part 1: Radio disturbance and immunity measuring apparatus“. EN 61000-4-3: “Electromagnetic Compatibility (EMC) - Part 4: Testing and measurements techniques - Section 3: Radiated, radio-frequency, electromagnetic field immunity test“. EN 61 000-4-2: “Electromagnetic Compatibility (EMC)

36、- Part 4: Testing and measurements techniques - Section 2: Electrostatic discharge immunity test. Basic EMC publication“. EN 61000-4-4: “Electromagnetic Compatibility (EMC); Part 4: Testing and measurements techniques - Section 4: Electrical fast transientburst immunity test. Basic EMC publication“.

37、 EN 61000-4-6: “Electromagnetic Compatibility (EMC) - Part 4: Testing and measurements techniques - Section 6: Immunity to conducted disturbances induced by radio-frequency fields“. EN 61000-4-1 1 : “Electromagnetic Compatibility (EMC); Part 4: Testing and measurements techniques - Section 11 : Volt

38、age dips, short interruptions and voltage variations immunity tests“. EN 61000-4-5: “Electromagnetic Compatibility (EMC) - Part 4: Testing and measurement techniques - Section 5: Surge immunity test“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of this ETS, the following definit

39、ions apply: ancillary equipment: Equipment (apparatus), used in connection with a receiver or transceiver is considered as an ancillary equipment (apparatus) if: - the equipment is intended for use in conjunction with a receiver, or transceiver to provide additional operational and/or control featur

40、es to the radio equipment (e.g. to extend control to another position or location); and - the equipment cannot be used on a stand alone basis to provide user functions independently of a receiver or transceiver; and - the receiver or transceiver to which it is connected, is capable of providing some

41、 intended operation such as transmitting and/or receiving without the ancillary equipment (.e. it is not a sub-unit of the main equipment essential to the main equipment basic functions). STD*ETSI ETS 300 327-ENGL 1797 3400855 0207241 175 Page 9 ETS 300 329: June 1997 base station equipment: Used to

42、 describe DECT equipment including Fixed Parts (FP) and/or Portable Parts (PP) as defined in ETS 300 175-2 4 which are powered via an AC power input port or a DC power input port. DECT equipment: Apparatus which includes one or more transceivers and/or receivers and/or parts thereof which conform to

43、 the requirements of ETS 300 175-2 4. host equipment: Any equipment which has a complete user functionality when not connected to the DECT radio equipment, and to which the DECT radio equipment provides additional functionality, and to which connection is necessary for the DECT radio equipment to of

44、fer functionality. integral antenna: An antenna designed to be connected to the equipment without the use of an external connector and considered to be part of the equipment. An integral antenna may be fitted internally or externally to the equipment. manufacturer: The legal entity responsible under

45、 the terms of the Council Directive 89/336/EEC 3 for placing the product on the market. mobile equipment: DECT equipment powered by a vehicular power supply. port: A particular interface of the specified equipment (apparatus) with the electro-magnetic environment. portable equipment: DECT equipment

46、powered by an internal battery. NOTE: More than one of the equipment classifications may apply to certain equipment, as described in subclause 5.2, dependent upon the manufacturers declaration of normal intended use. 3.2 Abbrevi ations For the purposes of this ETS, the following abbreviations apply:

47、 BER BPF BW CF BER CR CT DECT EMC ERP EUT FP LISN M RP PP RF SPL TR TT 4 4.1 Bit Error Ratio Band Pass Filter Band Width Carrier Frequency Bit Error Ratio Continuous phenomena applied to DECT Receive-only equipment Continuous phenomena applied to DECT Transceivers Digital Enhanced Cordless Telecommu

48、nications ElectroMagnetic Compatibility Ear Reference Point Equipment Under Test Fixed Part Line Impedance Stabilization Network Mouth Reference Point Portable Part Radio Frequency Sound Pressure Level Transient phenomena applied to DECT Receive-only equipment Transient phenomena applied to DECT Tra

49、nsceivers General test conditions Test condit Ions The equipment shall be tested under normal test conditions contained in the relevant product and basic standards or in the information accompanying the equipment, which are within the manufacturers declared range of humidity, temperature, and supply voltage. The test conditions shall be recorded in the test report. STD-ETSI ETS 300 327-ENGL 1777 3Li00855 02072LiLi 021 Page 10 ETS 300 329: June 1997 The test configuration shall be as close to normal intended use as possible, and shall be recorded in the test repor