ARMY MIL-H-1411 E-1991 HOOK TENT ASSEMBLY WALL SECTION《壁管屏吊钩装置》.pdf

《ARMY MIL-H-1411 E-1991 HOOK TENT ASSEMBLY WALL SECTION《壁管屏吊钩装置》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-H-1411 E-1991 HOOK TENT ASSEMBLY WALL SECTION《壁管屏吊钩装置》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、7 a - .a= c Y MIL-H-LLIE 83 9999906 OV67853 3 I INCH-POUND 1 MIL-H-1411E 15 January 1991 SUPERSEDING MIL-H-1411D 30 June :986 MILITARY SPECIFICATION HOOK, TENT, ASSEMBLY, WALL SECTION This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Sc

2、ope. This document covers a wall section tent hook assembly. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifica- tions, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specif

3、ied, the issues of these documents are . those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial coinments (recommendations, additions, deletions) and any pertinent data which may be

4、 used in improving this document should be addressed to: Army Natick Research, Development, and Engineering Center, Natick, MA 01760- 5017 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. U.S. AMSC NIA FSC 8340 DISTRIBUTION

5、 STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SPECIFICATIONS FEDERAL PPP-B-60 1 - Boxes, Wood, Cleated-Plywood PPP-2-636 - Baxes, Shipping, Fiberboard STANDARDS MI LI TARY MIL-ST

6、D-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets MS 27040 - Nut, Plain, Square-Steel, Cadmium Plated MS 35206 - Screw, Machine-Pan Head, Cross-R

7、ecessed, Carbon Attributes Steel, Cadmium Plated, UNC-2A (IN, /MM) (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 ot

8、her Go document Other Government documents, drawings, and publications. The following to the extent specified herein. Unless otherwise specified, the issues vernment documents, drawings, and publications form a part of this are those cited in the solicitation. DRAWINGS U.S. ARMY NATICK RESEARCH, DEV

9、ELOPMENT, AND ENGINEERING CENTER 5-4708 - Hook, Tent, Assembly, Wall Section; Style 1 5-4-709 - Hook, Tent, Assembly, Wall Section; Style 2 (Copies of drawings are available from the U.S. Army Natick Research, Development, and Engineering Center, ATTN: STRNC-UX, Natick, MA 01760-5017.) 2,2 Non-Gover

10、nment publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specif ied, the issues of doc

11、uments cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) A 148 - Steel Castings, High Strength, for Structural Purposes 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-L4LLE 3 = 9999906 0467855 7 MIL-H-141

12、1E A 385 - Providing High-Quality Zinc Coatings (Hot-Dip) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publication

13、s are normally available from organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order. of precedence. In the event of a conflict between the text of this document and the references cited herein

14、, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in

15、 accordance with 4.3 3.2 Materials. The materials used shall conform to the applicable referenced documents specified herein. It is encouraged that recycled material be used when practical as long as it meets the requirements of this specification. 3.2.1 Steel casting. Steel casting shall conform to

16、 grade 90-60 or 105-85 of ASTM A 148/A 148M. 3.2.2 Machine screw and nut, Machine screw and nut shall conform to MS 35206-231 and MS 27040-6 respectively. 3.3 Construction. Construction of the hook shall conform to either Drawing 5-4-708 or 5-4-709 and as specified herein. The hook shall be capable

17、of withstanding a minimum pull of 150 pounds without fracture, permanent deformation, or separation when tested as specified in 4.4.4. 3.3.1 Hook body and clamp. The hook body and clamp shall be of cast steel as specified in 3.2.1. 3.4 Finish. 3.4.1 Castings. Castings for body and clamp shall be gro

18、und, filed, polished, or tumbled smooth and have a natural finish. Castings shall be zinc plated per ASTM A 385. 3.5 Workmanship. The completely finished tent hooks shall be free of blow- holes, porosity, hard spots, burrs, cracks, or sharp edges. Threads of screw and nut shall be free of damage to

19、the extent that the nut cannot be tightened or loosened. Screw and nut shall be free from rust: The end item shall conform to the quality of product established by this specification and the occurance of defects shall not exceed the applicable acceptable quality levels. 3 Provided by IHSNot for Resa

20、leNo reproduction or networking permitted without license from IHS-,-,- - MIL-H-14LLE 3 m 9999906 046785b 9 m sp 9 4, QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all

21、 inspection requirements (examinations and tests) as specified herein. Except as atherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Gover

22、nment. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items shall meet all requirements of sec

23、tions 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or s

24、upplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this . does not authorize submission of known defective material, ei

25、ther indicated or actual, nor does it commit the Government to accept defective material. 4,1,2 Responsibility for dimensional requirements. Unless otherwise specified in the contract or purchase order, the contractor is responsible for ensuring .that.all specified dimensions have been met, When dim

26、ensions cannot be examined on the end item, inspection shall be made at any point, or at all points in the manufacturing process necessary to ensure compliance with all dimensional requirements. a 4.2 Classification of inspections. The inspection requirements specified herein are classified as follo

27、ws: a. b, Quality conformance inspection (see 4.4). First article inspection (see 4.3). 4.3 First article inspection. When a first article is required (see 3.1 and 6.2), it shall be examined for defects specified in 4.4.2 and 4.4.3 and shall be tested for the characteristic specified in 4.4.4. Any n

28、onconformance shall be cause for the rejection of the first article. 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.4.1 Component and material inspection, In accordance with 4.1, components and materials sh

29、all be inspected in accordance with all the requirements of referenced documents unless otherwise excluded, amended, modified, or qualified in this specification or applicable purchase document. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-s n -

30、* MIL-H-LYLLE 83 9999906 OYb7857 O MIL-H-1411E 4.4.2 End item visual examination. The end items shall be examined for the defects listed in table I. The lot size shall be expressed in units of tent hooks. The sample unit shall be one tent hook. The inspection level shall be II, and the acceptable qu

31、ality level (AQL), expressed in terms of defects per hundred units, shall be 2.5 for major defects and 6.5 for total (major and minor combined) defects. TABLE I. End item visual defects Classification Examine Defect Major Minor Finish: Casting Screw and nut Construction and workmanship 0 Not zinc pl

32、ated or partially zinc Coating is blistered, pitted, not adherent, or showing evidence of corrosion 102 plated 101 Not cadmium plated 103 Plating is blistered, pitted, not adherent, or not continuous 104 Evidence of corrosion 105 106 107 201 Not smooth Blow-holes, porosity, hard spots, burrs, flashi

33、ngs, cracks or sharp edges Any component or part missing Mating surfaces between clamp and Not assembled as shown on applicable Threads of screw or nut damaged to the body not flat drawing extent that the nut cannot be tightened or loosened insufficiently peened that could result in loss of nut 203

34、End of screw not peened or Wrong type screw or nut 204 108 202 109 4.4.3 End itern dimensional examination. The end items shall be examined for nonconformance to the dimensions specified on the drawings. Only those dimensions that can be evaluated without damaging or disassembling the end items shal

35、l be examined. Any dimension not within the specified tolerance shall be classified as a defect. The lot size shall be expressed in units of tent hooks. The sample unit shall be one tent hook, The inspection level shall be S-2, and the AQL, expressed in terms of defects per hundred units, shall be 4

36、.0. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-1411E 4.4,4 End item testing. Testing of the completely fabricated tent hook shall be performed in accordance with table II for the specified characteristic. The lot size shall be expressed

37、in units of tent hooks. The sample unit shall be one tent hook, shall be cause for rejection of the lot. The inspection level shall be S-1. The failire of any pell test TABLE II. End item test Number of deter- Requirement Test minations per Results Character i s tic paragraph method sample unit repo

38、rt as Pull test load 3.3 4.5.1 1 Pass or fail 4.4.5 Packaging examination. The fully packaged end items shall be examined for the defects listed below. The lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged, The inspection leve

39、l shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 2.5. Examine Defect Marking (exterior Omitted; incorrect; illegible; of improper and interior) size, location, sequence, or method of application Materials Any component missing, damaged, or not as specified Workma

40、nship Con tent Inadequate application of components, such as: incomplete sealing or closure of flap, improper taping, loose strapping or inadequate stapling Bulged or distorted container Number of hooks per unit pack and shipping container not as specified 4.4.6 Palletization examination, The fully

41、packaged and palletized end items shall be examined for the defects listed below. The lot size shall be expressed in units of palletized unit loads. The sample unit shall be one palletized unit load, fully packaged. The inspection level shall be S-1, and the AQL, expressed in terms of defects per hu

42、ndred units, shall be 6.5. Examine Defect Finished dimensions Length, width, or height exceeds specified maximum requirement Palletization Pallet pattern not as specified Load not bonded as specified 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

43、J. * MIL-H-LYLLE 83 m 9999906 0467859 Y m MIL-H- 14 11E Weight Marking Exceeds maximum load limits Omitted; incorrect; illegible; of improper size, location, sequence, or method of application 4.5 Method of inspection, 4.5.1 Pull test. The hook shall be subjected to the pull test load, as shown on D

44、rawing 5-4-708 or 5-4-709, as applicable. The load rate shall not exceed 1000 pounds per minute until a load of 150 pounds is reached. After the load has been released, the hook shall be examined. Any hook having evidence of fracture, permanent distortion, or separation shall constitute failure of t

45、he tes t. 5. PACKAGING 5.1 Preservation. Preservation shall be level A or Commercial, as specified (see 6.2). 5.1.1 Level A preservation. Unless otherwise specified (see 6.2), five hundred hooks of like description shall be unit packed in a close-fitting fiberboard box conforming to style RSC, type

46、CF or CF, class domestic, grade 200 of PPP-B-636, Each box shall be agitated to ensure a compact and well-filled box. Closure shall be in accordance with the appendix of PPP-B-636. 5.2.1 Level A packing. Unless otherwise specified (see 6.21, three thousand hooks of like description, preserved as spe

47、cified in 5.1, shall be packed in a grade A or By type 2 load of PPP-B-601. Each shipping container shall be completely filled, with no voids, and shall be of a size that can be palletized in accordance with MIL-STD-147. Shipping containers shall be closed, waterproofed, and reinforced in accordance

48、 with the appendix of PPP-B-601. close-fitting cleated plywood box conforming to overseas type, style A or J, 5.2.2 Level B packing. Unless otherwise specified (see 6-21, three thousand hooks of like description, preserved as specified in 5.1, shall be packed in a close-fitting fiberboard box confor

49、ming to style FTC, type CF, variety DW, or SF, grade 350 of PPP-B-636, Each shipping container shall be completely filled with no voids, and shall be of a size that can be palletized in accordance with MIL-STD-147, Each shipping container shall be closed and reinforced in accordance with the appendix of PPP-B-636. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-LLIJE 83 99999O