ETSI EN 303 203-2-2014 Electromagnetic compatibility and Radio spectrum Matters (ERM) Short Range Devices (SRD) Medical Body Area Network Systems (MBANSs) operating in the 2 483 5 _1.pdf

《ETSI EN 303 203-2-2014 Electromagnetic compatibility and Radio spectrum Matters (ERM) Short Range Devices (SRD) Medical Body Area Network Systems (MBANSs) operating in the 2 483 5 _1.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 303 203-2-2014 Electromagnetic compatibility and Radio spectrum Matters (ERM) Short Range Devices (SRD) Medical Body Area Network Systems (MBANSs) operating in the 2 483 5 _1.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 303 203-2 V1.1.1 (2014-11) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Medical Body Area Network Systems (MBANSs) operating in the 2 483,5 MHz to 2 500 MHz range; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R

2、 Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carri

3、ed out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Tech

4、nical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). For non EU countries the present document may be used for regulatory (Type Approval) purposes. The present document has been produced by ETSI in response to mandate M/284 issued from the European Commission under Directi

5、ve 98/34/EC i.7 as amended by Directive 98/48/EC i.6. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC i.3. See article 5.1 of Dir

6、ective 1999/5/EC i.3 for information on presumption of conformity and Harmonized Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC i.3 are summarized in annex A. The present document

7、is part 2 of a multi-part deliverable covering Medical Body Area Network Systems (MBANSs) operating in the 2 483,5 MHz to 2 500 MHz range, as described in the systems reference document for the equipment, TR 101 557 i.1, and as identified below: Part 1: “Technical characteristics and test methods“;

8、Part 2: “Harmonized EN covering the essential requirements of article 3.2 of the R Short Range Devices (SRD); Medical Body Area Network Systems (MBANSs) operating in the 2 483,5 MHz to 2 500 MHz range; Part 1: Technical characteristics and test methods“. 2 ETSI TR 100 028 (V1.4.1) (12-2001): “Electr

9、omagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics“. 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a

10、 particular subject area. i.1 ETSI TR 101 557: “Electromagnetic compatibility and Radio spectrum Matters (ERM); System Reference document (SRdoc); Medical Body Area Network Systems (MBANSs) in the 1 785 MHz to 2 500 MHz range“. ETSI ETSI EN 303 203-2 V1.1.1 (2014-11) 8i.2 CEPT/ERC/REC 70-03: “Relati

11、ng to the use of Short Range Devices (SRD)“. i.3 Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R A guide to the production of Harmonized Standards for appl

12、ication under the R the value of the measurement uncertainty for the measurement of each parameter shall be included in the test report; the value of the measurement uncertainty shall be, for each measurement, equal to or lower than the figures given in table 3 (Measurement uncertainties up to 12,5

13、GHz for RF measurements) in clause 7 in EN 303 203-1 1. For the test methods, according to the present document, the measurement uncertainty figures shall be calculated in accordance with TR 100 028 2 and shall correspond to an expansion factor (coverage factor) k = 1,96 or k = 2 (which provide conf

14、idence levels of respectively 95 % and 95,45 % in the case where the distributions characterizing the actual measurement uncertainties are normal (Gaussian). ETSI ETSI EN 303 203-2 V1.1.1 (2014-11) 12The measurement uncertainties are given in table 3 in clause 7 in EN 303 203-1 1. 5.3 Essential radi

15、o test suites 5.3.1 Frequency error The test specified in EN 303 203-1 1, clause 8.1 shall be carried out. 5.3.2 Emission bandwidth The test specified in EN 303 203-1 1, clause 8.2 shall be carried out. 5.3.3 Effective isotropic radiated power The test specified in EN 303 203-1 1, clause 8.3 shall b

16、e carried out. 5.3.4 Transmitter spurious emissions The test specified in EN 303 203-1 1, clause 8.4 shall be carried out. 5.3.5 Out-of-band emissions The test specified in EN 303 203-1 1, clause 8.5 shall be carried out. 5.3.6 Frequency stability under low voltage conditions The test specified in E

17、N 303 203-1 1, clause 8.6 shall be carried out. 5.3.7 Receiver spurious emissions The test specified in EN 303 203-1 1, clause 9.1 shall be carried out. 5.3.8 Spectrum access The tests for spectrum access requirements specified in EN 303 203-1 1, clause 10 shall be carried out. 5.3.9 Normal test-con

18、ditions The normal test procedures shall be as specified in EN 303 203-1 1, clause 5.3. 5.3.10 Extreme test-conditions The extreme test procedures shall be as specified in EN 303 203-1 1, clause 5.4. 5.3.11 Test power source The test power source shall meet the requirements of EN 303 203-1 1, clause

19、 5.2. 5.3.12 Choice of samples for test suites Measurement shall be performed on samples of equipment defined in EN 303 203-1 1, clause 4.2. ETSI ETSI EN 303 203-2 V1.1.1 (2014-11) 13Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) The HS Requirements and confo

20、rmance Test specifications Table (HS-RTT) in table A.1 serves a number of purposes, as follows: it provides a statement of all the requirements in words and by cross reference to (a) specific clause(s) in the present document or to (a) specific clause(s) in (a) specific referenced document(s); it pr

21、ovides a statement of all the test procedures corresponding to those requirements by cross reference to (a) specific clause(s) in the present document or to (a) specific clause(s) in (a) specific referenced document(s); it qualifies each requirement to be either: - Unconditional: meaning that the re

22、quirement applies in all circumstances; or - Conditional: meaning that the requirement is dependent on the manufacturer having chosen to support optional functionality defined within the schedule. in the case of Conditional requirements, it associates the requirement with the particular optional ser

23、vice or functionality; it qualifies each test procedure to be either: - Essential: meaning that it is included with the Essential Radio Test Suite and therefore the requirement shall be demonstrated to be met in accordance with the referenced procedures; - Other: meaning that the test procedure is i

24、llustrative but other means of demonstrating compliance with the requirement are permitted. Table A.1: HS Requirements and conformance Test specifications Table (HS-RTT) Harmonized Standard EN 303 203-2 The following requirements and test specifications are relevant to the presumption of conformity

25、under the article 3.2 of the R those designated “O“ make up the Other Test Suite; for those designated “X“ there is no test specified corresponding to the requirement. The completion of all tests classified “E“ as specified with satisfactory outcomes is a necessary condition for a presumption of con

26、formity. Compliance with requirements associated with tests classified “O“ or “X“ is a necessary condition for presumption of conformity, although conformance with the requirement may be claimed by an equivalent test or by manufacturers assertion supported by appropriate entries in the technical con

27、struction file. Clause Number Identification of clause(s) defining the test specification in the present document unless another document is referenced explicitly. Where no test is specified (that is, where the previous field is “X“) this field remains blank. ETSI ETSI EN 303 203-2 V1.1.1 (2014-11)

28、15Annex B (informative): Change History Void. ETSI ETSI EN 303 203-2 V1.1.1 (2014-11) 16Annex C (informative): Bibliography Recommendation ITU-T O.153: “Basic parameters for the measurement of error performance at bit rates below the primary rate“. Council Directive 89/336/EEC of 3 May 1989 on the a

29、pproximation of the laws of the Member States relating to electromagnetic compatibility (EMC Directive). ETSI EN 301 489: “Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services“. Council Directive 73/23/EEC of 19

30、 February 1973 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (LV Directive). ECC Report 201: “Compatibility study between MBANS operating in the 2400 - 2483.5 MHz and 2483.5 - 2500 MHz bands and other systems in the same bands or in adjacent bands“. CEPT/ERC/REC 74-01: “Unwanted Emissions in the Spurious Domain“. ETSI ETSI EN 303 203-2 V1.1.1 (2014-11) 17History Document history V1.1.0 July 2014 EN Approval Procedure AP 20141030: 2014-07-02 to 2014-10-30 V1.1.1 November 2014 Publication