ETSI EN 302 609-2016 Short Range Devices (SRD) Radio equipment for Euroloop railway systems Harmonised Standard covering the essential requirements of article 3 2 of the Directive _1.pdf

《ETSI EN 302 609-2016 Short Range Devices (SRD) Radio equipment for Euroloop railway systems Harmonised Standard covering the essential requirements of article 3 2 of the Directive _1.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 302 609-2016 Short Range Devices (SRD) Radio equipment for Euroloop railway systems Harmonised Standard covering the essential requirements of article 3 2 of the Directive _1.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 302 609 V2.1.1 (2016-12) Short Range Devices (SRD); Radio equipment for Euroloop railway systems; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 302 609 V2.1.1 (2016-12) 2 Reference REN/ERM-TG28-50

2、8 Keywords harmonised standard, radio, SRD, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important no

3、tice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authori

4、zation of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be

5、 aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the followin

6、g services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF vers

7、ion shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI regist

8、ered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 302 609 V2.1.1 (2016-12) 3 Contents Intellectu

9、al Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions, symbols and abbreviations . 7g33.1 Definitions 7g33.2 Symbols 8g33.3 Abbreviations . 8g34 Technical requirements specif

10、ications . 8g34.1 Environmental profile . 8g34.2 Transmitter conformance requirements 8g34.2.1 OBE TX field strength and Transmitter mask 8g34.2.1.1 Applicability 8g34.2.1.2 Limits 8g34.2.1.3 Conformance . 9g34.2.1.4 Maximum Allowable Measurement Uncertainty 9g34.2.2 OBE unwanted emissions . 9g34.2.

11、2.1 Applicability 9g34.2.2.2 Limits 9g34.2.2.3 Conformance . 9g34.2.2.4 Maximum Allowable Measurement Uncertainty 10g34.2.3 Euroloop transmitter field strength . 10g34.2.3.1 Applicability 10g34.2.3.2 Limits 10g34.2.3.3 Conformance . 10g34.2.4 Euroloop transmitter mask 10g34.2.4.1 Applicability 10g34

12、.2.4.2 Limit 10g34.2.4.3 Conformance . 11g34.3 Receiver Conformance requirements . 11g34.3.1 OBE Receiver sensitivity 11g34.3.1.1 Applicability 11g34.3.1.2 Limits 11g34.3.1.3 Conformance . 11g34.3.2 OBE Receiver co-channel rejection 11g34.3.2.1 Applicability 11g34.3.2.2 Limits 11g34.3.2.3 Conformanc

13、e . 11g34.3.3 OBE Receiver blocking 11g34.3.3.1 Applicability 11g34.3.3.2 Limits 11g34.3.3.3 Conformance . 11g34.3.4 OBE Receiver radio-frequency intermodulation 11g34.3.4.1 Applicability 11g34.3.4.2 Limits 12g34.3.4.3 Conformance . 12g34.3.5 Euroloop Receiver sensitivity . 12g34.3.5.1 Applicability

14、 12g34.3.5.2 Limits 12g34.3.5.3 Conformance . 12g3ETSI ETSI EN 302 609 V2.1.1 (2016-12) 4 5 Testing for compliance with technical requirements 12g35.1 Environmental conditions for testing . 12g35.2 General conditions for testing 12g35.2.1 Test conditions 12g35.2.2 Test power source . 12g35.2.3 Norma

15、l test conditions 13g35.2.3.1 Normal temperature and humidity 13g35.2.3.2 Normal test power source 13g35.2.3.2.1 Mains voltage 13g35.2.3.2.2 Other power sources 13g35.2.4 Choice of equipment for test suites . 13g35.2.4.1 Choice of model 13g35.2.4.2 Measuring receiver 13g35.3 Interpretation of the me

16、asurement results 14g36 Performance Test Suites . 14g36.1 Conformance methods of measurement for transmitters 14g36.1.1 OBE Tx field strength and Transmitter Mask . 14g36.1.2 OBE Unwanted Emission . 15g36.1.3 Euroloop field strength measurements 15g36.1.4 Euroloop transmitter conducted measurements

17、16g36.2 Conformance Methods of Measurement for Receiver 16g36.2.1 OBE receiver sensitivity . 16g36.2.2 OBE Receiver co-channel rejection 16g36.2.3 OBE Receiver blocking 16g36.2.4 OBE Receiver radio-frequency intermodulation 16g36.2.5 Euroloop receiver sensitivity 17g3Annex A (normative): Relationshi

18、p between the present document and the essential requirements of Directive 2014/53/EU . 18g3Annex B (normative): Field strength measurements along the Euroloop 19g3Annex C (informative): Change History 20g3History 21g3ETSI ETSI EN 302 609 V2.1.1 (2016-12) 5 Intellectual Property Rights IPRs essentia

19、l or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially

20、Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guaran

21、tee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electroma

22、gnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.8 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of th

23、e Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table

24、 A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. National transposition dates Date of adoption of this EN: 12 December 2016 Date of latest announcement o

25、f this EN (doa): 31 March 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 September 2017 Date of withdrawal of any conflicting National Standard (dow): 30 September 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “sh

26、ould not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introducti

27、on The Euroloop communication system is defined by the specifications 1 and 2 of the UNISIG consortia. ETSI ETSI EN 302 609 V2.1.1 (2016-12) 6 1 Scope The present document covers the technical requirements for radio transmitters and receivers used in the Euroloop transmission system. The system is u

28、sed in railway systems. The present document applies to the following equipment: 1) The On-Board Equipment (OBE) receiving the Euroloop signal and the OBE comprises a receiver fitted with a dedicated antenna. 2) The Track-Side Equipment (Euroloop) transmitting the Euroloop signal that is always inst

29、alled in an inner or outer foot of a rail. The Euroloop transmission system operates in frequency bands listed in table 1 in accordance with the EC Decision 2013/752/EU i.2, and ERC Recommendation 70-03 i.3, annex 4. These radio equipment types are capable of operating at the following frequencies a

30、s given below in table 1. Table 1: Radio communications frequencies Radio communications frequencies OBE receive frequency band 11,1 -16,0 MHz OBE transmit frequency band 27,09 - 27,10 MHz Euroloop receiver frequency band 27,09 - 27,10 MHz Euroloop transmit frequency band 11,1 -16,0 MHz Euroloop tra

31、nsmit modulation BPSK, DSSS chip rate 4,516 MHz The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. 2 References 2.1 Normative references References are either sp

32、ecific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are n

33、ot found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for

34、 the application of the present document. 1 ERTMS/ETCS: “FFFIS for Euroloop“, SUBSET-044, Issue 2.4.0, 29thFebruary 2012. 2 ERTMS/ETCS: “Test Specification for Euroloop“, SUBSET-103, Issue 1.1.0, 29thFebruary 2012. 2.2 Informative references References are either specific (identified by date of publ

35、ication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at t

36、he time of publication, ETSI cannot guarantee their long term validity. ETSI ETSI EN 302 609 V2.1.1 (2016-12) 7 The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU

37、 of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC, (OJ L153, 22.5.2014, p62). i.2 EC Decision 2013/752/EU: “Commission Implementing

38、Decision of 11 December 2013 amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range devices and repealing Decision 2005/928/EC“. i.3 CEPT/ERC/Recommendation 70-03: “Relating to the use of Short Range Devices (SRD)“. i.4 ETSI TR 100 028-1 (V1.4.1): “Electromagneti

39、c compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 1“. i.5 ETSI TR 100 028-2 (V1.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment character

40、istics; Part 2“. i.6 ETSI EN 300 330-1 (V1.7.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in the frequency range 9 kHz to 30 MHz; Part 1: Technical characteristics and

41、 test methods“. i.7 CENELEC EN 50121-2 (2015-03): “Railway applications - Electromagnetic compatibility - Part 2: Emission of the whole railway system to the outside world“ / Applies in conjunction with EN 50121-1 (2000-09)“. i.8 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a s

42、tandardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. 3 Definitions, symbols and abbreviations 3.1 D

43、efinitions For the purposes of the present document, the following terms and definitions apply: dedicated antenna: removable antenna supplied and tested with the radio equipment, designed as an indispensable part of the equipment eurobalise: wayside transmission unit that uses the magnetic transpond

44、er technology NOTE: Its main function is to transmit and/or receive signals through the air gap. The Eurobalise is a single device mounted on the track, which communicates with a train passing over it. euroloop: wayside transmission unit that uses the magnetic transmission technology NOTE: Its main

45、function is to transmit signals through the air gap. The Euroloop is a single device mounted on the track, which communicates with a train passing over it. magnetic transmission technology: method that uses magnetic coupling in the air gap between a transmitter and a receiver NOTE: In the Euroloop t

46、ransmission system context, it considers systems using the band 11,1 - 16,0 MHz for Uplink (track to train) transmission. rf carrier: fixed radio frequency prior to modulation uplink: transmission link from the Euroloop to the OBE ETSI ETSI EN 302 609 V2.1.1 (2016-12) 8 3.2 Symbols For the purposes

47、of the present document, the following symbols apply: f Frequency Ohm R Distance RC Chip rate wavelength 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: BPSK Binary Phase Shift Keying CW Continous Wave dB deciBel (logarithmic scale) DSSS Direct Sequence

48、 Spread Spectrum ERC European Radiocommunications Committee LOOMO LOOp MOdem OBE On-Board Equipment RF Radio Frequency RMS Root Mean Square SRD Short Range Device TX Transmitter UNISIG UNion Industry of SIGnalling VSWR Voltage Standing Wave Ratio 4 Technical requirements specifications 4.1 Environme

49、ntal profile The technical requirements of the present document apply under the environmental profile for operation of the equipment, which shall be declared by the manufacturer. The equipment shall comply with all the technical requirements of the present document at all times when operating within the boundary limits of the declared operational environmental profile. 4.2 Transmitter conformance requirements 4.2.1 OBE TX field strength and Transmitter mask 4.2.1.1 Applicability This test only applies to the OBE. The radiated H-field mask