ETSI EN 301 843-5-2016 ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services Harmonised Standard covering the essential requirements of article 3 1b .pdf

《ETSI EN 301 843-5-2016 ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services Harmonised Standard covering the essential requirements of article 3 1b .pdf》由会员分享，可在线阅读，更多相关《ETSI EN 301 843-5-2016 ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services Harmonised Standard covering the essential requirements of article 3 1b .pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 301 843-5 V2.1.1 (2016-03) ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmonised Standard covering the essential requirements of article 3.1b of the Directive 2014/53/EU; Part 5: Specific conditions for MF/HF radiotelephone transmitters and receive

2、rs HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 843-5 V2.1.1 (2016-03) 2 Reference REN/ERM-EMC-350 Keywords EMC, harmonised standard, HF, maritime, MF, radio, receiver ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623

3、562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of

4、 any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document F

5、ormat (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/E

6、TSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical,

7、 including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Stand

8、ards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are

9、 Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 301 843-5 V2.1.1 (2016-03) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions, symbols and abbr

10、eviations . 7g33.1 Definitions 7g33.2 Symbols 7g33.3 Abbreviations . 7g34 General and operational requirements 7g34.1 Environmental profile . 7g34.2 Arrangements for test signals . 8g34.2.0 General 8g34.2.1 Arrangements for test signals at the input of the transmitter 8g34.2.2 Arrangements for test

11、signals at the output of the transmitter 8g34.2.3 Arrangements for test signals at the input of the receiver . 8g34.2.4 Arrangements for test signals at the output of the receiver . 8g34.2.5 Arrangements for testing transmitter and receiver together (as a system) 8g34.3 Exclusion bands 8g34.3.0 Gene

12、ral 8g34.3.1 Exclusion bands for receivers and receiver parts of transceivers 8g34.3.2 Exclusion band for transmitters 9g34.4 Narrow band responses on receivers 9g34.5 Normal test modulation 9g34.6 Artificial Antennae (non-radiating test load) 9g35 Performance assessment . 10g35.1 General . 10g35.2

13、Equipment which can provide a continuous communication link 10g35.3 Equipment which does not provide a continuous communication link 10g35.4 Ancillary equipment . 10g35.5 Equipment classification 10g36 Performance criteria . 10g36.0 General . 10g36.1 Performance criteria A for continuous phenomena a

14、pplied to transmitters and receivers 10g36.2 Performance criteria B for transient phenomena applied to transmitters and receivers . 11g36.3 Performance criteria C applied to power supply failure . 11g36.4 Performance check . 11g36.4.0 General 11g36.4.1 Transmitter 11g36.4.2 Receiver 11g36.5 Performa

15、nce criteria for equipment which does not provide a continuous communication link 11g36.6 Performance criteria for ancillary equipment tested on a stand-alone basis . 12g37 Applicability overview . 12g37.1 Emission . 12g37.1.1 General 12g37.1.2 Special conditions . 12g37.2 Immunity 12g37.2.1 General

16、 12g37.2.2 Special conditions . 12g3ETSI ETSI EN 301 843-5 V2.1.1 (2016-03) 4 Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 13g3Annex B (informative): Examples of types of MF/HF marine radiotelephone equipment in the scope of

17、the present document 14g3B.0 General . 14g3B.1 Radiotelephone transmitters and receivers for the maritime mobile service operating in the MF/HF bands 14g3History 15g3ETSI ETSI EN 301 843-5 V2.1.1 (2016-03) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document

18、 may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETS

19、I standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs

20、 not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (E

21、RM). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.4 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available o

22、n the market of radio equipment and repealing Directive 1999/5/EC i.1. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 of ETSI EN 301 843-1 1 confers, within the li

23、mits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 5 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. National tr

24、ansposition dates Date of adoption of this EN: 21 March 2016 Date of latest announcement of this EN (doa): 30 June 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 31 December 2016 Date of withdrawal of any conflicting National Standard (dow): 31 December 2

25、017 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must no

26、t“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI EN 301 843-5 V2.1.1 (2016-03) 6 1 Scope The present document together with ETSI EN 301 843-1 1, covers the assessment of MF/HF radiotelephone transmitters and receivers for the maritime mobile service, and ancilla

27、ry equipment in respect of ElectroMagnetic Compatibility (EMC). Technical specifications related to the antenna port and emissions from the enclosure port of marine radiotelephone transmitters and receivers are not included in the present document. Such technical specifications are found in the rela

28、ted product standards for the effective use of the radio spectrum. The present document specifies the applicable test conditions, performance assessment, and performance criteria for radiotelephone transmitters and receivers for the maritime mobile service and the associated ancillary equipment. Exa

29、mples of types of MF/HF radiotelephone transmitters and receivers for the maritime mobile service covered by the present document are given in annex A. In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present document and ETSI EN 301 843-1 1

30、, the provisions of the present document take precedence. The electromagnetic environment used in the present document to develop the technical specifications encompasses the electromagnetic environment on-board ships as identified in CENELEC EN 60945 i.3. 2 References 2.1 Normative references Refer

31、ences are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced do

32、cuments which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced document

33、s are necessary for the application of the present document. 1 ETSI EN 301 843-1 (V2.1.1) (03-2016): “ElectroMagnetic Compatibility (EMC) standard for marine radio equipment and services; Harmonised Standard covering the essential requirements of article 3.1b of the Directive 2014/53/EU; Part 1: Com

34、mon technical requirements“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenc

35、ed document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist t

36、he user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.2 ETS

37、I EN 300 373-2 (V1.1.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Maritime mobile transmitters and receivers for use in the MF and HF bands; Part 2: Harmonized EN covering essential requirements under article 3.2 of the R b) 500 mW for loudspeaker reception; c) 0 dBm (1mW) in

38、to 600 for the audio line outputs. 3.2 Symbols For the purposes of the present document, the following symbols apply: emf electromotive force F1B Frequency modulation, single channel containing quantized or digital information with the use of a modulating sub-carrier, telegraphy for automatic recept

39、ion. J3E Single Sideband, suppressed carrier, single channel containing analogue information, telephony rms root mean square SINAD (Signal + Noise + Distortion) / (Noise + Distortion) 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: AGC Automatic Gain Co

40、ntrol DSC Digital Selective Calling EMC ElectroMagnetic Compatibility EUT Equipment Under Test HF High Frequency MF Medium Frequency MF/HF Medium Frequency/High Frequency PEP Peak Envelope Power RF Radio Frequency SINAD Signal-to-noise and distortion ratio 4 General and operational requirements 4.1

41、Environmental profile The provisions of ETSI EN 301 843-1 1, clause 4.1 shall apply with the following modifications. For emission and immunity tests the normal test modulation, test arrangements, etc., as specified in the present document, clauses 4.1 to 4.5, shall apply. ETSI ETSI EN 301 843-5 V2.

42、1.1 (2016-03) 8 The test shall be carried out at a point within the specified normal operating environmental range of temperature and humidity with the equipment connected to the normal power supply voltage. 4.2 Arrangements for test signals 4.2.0 General The provisions of ETSI EN 301 843-1 1, claus

43、e 4.2 shall apply. 4.2.1 Arrangements for test signals at the input of the transmitter The provisions of ETSI EN 301 843-1 1, clause 4.2.1 shall apply. 4.2.2 Arrangements for test signals at the output of the transmitter The provisions of ETSI EN 301 843-1 1, clause 4.2.2 shall apply. 4.2.3 Arrangem

44、ents for test signals at the input of the receiver The provisions of ETSI EN 301 843-1 1, clause 4.2.3 shall apply with the following modifications. The wanted RF input signal, coupled to the receiver, shall be modulated with normal test modulation as specified for that type of equipment (see clause

45、 4.5). The level of the wanted signal shall be as follows: MF (1 605 kHz to 4 000 kHz) J3E Mode: +56 dBuV F1B Mode: +45 dBuV HF (4 MHz to 27,5 MHz) J3E Mode: +51 dBuV F1B Mode: +40 dBuV Measurements shall only be made in F1B mode where the EUT does not have J3E mode. 4.2.4 Arrangements for test sign

46、als at the output of the receiver The provisions of ETSI EN 301 843-1 1, clause 4.2.4 shall apply as appropriate. 4.2.5 Arrangements for testing transmitter and receiver together (as a system) The provisions of ETSI EN 301 843-1 1, clause 4.2.5 shall apply as appropriate. 4.3 Exclusion bands 4.3.0 G

47、eneral The provisions of ETSI EN 301 843-1 1, clause 4.3 shall apply as appropriate. The emission measurement and immunity test exclusions are referred to as “exclusion bands“ and are defined in the clauses 4.3.1 and 4.3.2. 4.3.1 Exclusion bands for receivers and receiver parts of transceivers The e

48、xclusion band for marine radiotelephone receivers and receivers of transceivers is the frequency range determined by the switching range, as declared by the manufacturer, extended as follows: - the lower frequency of the exclusion band is the lower frequency of the switching range, minus 5 % of the

49、centre frequency of the switching range, or minus 10 MHz, whichever will result in the lowest frequency; - the upper frequency of the exclusion band is the upper frequency of the switching range, plus 5 % of the centre frequency of the switching range, or plus 10 MHz, whichever will result in the highest frequency. The switching range is the maximum frequency range over which the receiver can be operated without reprogramming or realignment. ETSI ETSI EN 301 843-5 V2.1.1 (2016-03) 9 4.3.2 Exclusion band for transmitters The exclusion ba