ETSI EN 301 489-3-2013 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 3 Specific .pdf

《ETSI EN 301 489-3-2013 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 3 Specific .pdf》由会员分享，可在线阅读，更多相关《ETSI EN 301 489-3-2013 Electromagnetic compatibility and Radio spectrum Matters (ERM) ElectroMagnetic Compatibility (EMC) standard for radio equipment and services Part 3 Specific .pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 301 489-3 V1.6.1 (2013-08) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and 246 GHz Harmonized E

2、uropean Standard ETSI ETSI EN 301 489-3 V1.6.1 (2013-08) 2Reference REN/ERM-EMC-279 Keywords EMC, SRD ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la So

3、us-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between

4、such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be sub

5、ject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ET

6、SI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2013. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the E

7、TSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 301 489

8、-3 V1.6.1 (2013-08) 3Contents Intellectual Property Rights 5g3Foreword . 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions and abbreviations . 7g33.1 Definitions 7g33.2 Abbreviations . 7g34 Test conditions . 8g34.1 General . 8g34.2 Arrangements f

9、or test signals . 8g34.2.1 Arrangements for test signals at the input of the transmitter 8g34.2.2 Arrangements for test signals at the output of the transmitter 8g34.2.3 Arrangements for test signals at the input of the receiver . 8g34.2.4 Arrangements for test signals at the output of the receiver

10、. 9g34.2.5 Arrangements for testing transmitter and receiver together (as a system) 9g34.3 Exclusion bands 9g34.3.1 Exclusion bands for receivers . 9g34.3.2 Exclusion band for transmitters 10g34.4 Narrow band responses of receivers . 10g34.5 Normal test modulation 10g35 Performance assessment . 11g3

11、5.1 General . 11g35.2 Equipment which can provide a continuous communications link 11g35.3 Equipment which does not provide a continuous communications link . 11g35.4 Ancillary equipment . 11g35.5 Equipment classification 11g36 Performance criteria . 12g36.1 Classification of SRD equipment . 12g36.2

12、 General performance criteria 12g36.3 Performance table . 12g36.4 Performance criteria for Continuous phenomena applied to Transmitters (CT) 13g36.5 Performance criteria for Transient phenomena applied to Transmitters (TT) 13g36.6 Performance criteria for Continuous phenomena applied to Receivers (C

13、R) . 13g36.7 Performance criteria for Transient phenomena applied to Receivers (TR) 14g36.8 Performance criteria for ancillary equipment tested on a stand alone basis . 14g37 Applicability overview . 14g37.1 Emission . 14g37.1.1 General 14g37.1.2 Special conditions . 14g37.2 Immunity 14g37.2.1 Gener

14、al 14g37.2.2 Special conditions . 15g3Annex A (informative): Examples of Short Range Devices (SRD) in the scope of the present document 16g3A.1 Short Range Devices (SRD) with RF power levels ranging up to 500 mW and intended for operation in the frequency range 25 MHz to 1 000 MHz . 16g3A.2 Short Ra

15、nge Devices (SRD) intended for operation in the frequency range 9 kHz to 25 MHz, and inductive loop systems intended for operation in the frequency range 9 kHz to 30 MHz . 16g3ETSI ETSI EN 301 489-3 V1.6.1 (2013-08) 4A.3 Short Range Devices (SRD) intended for operation in the frequency range 1 GHz t

16、o 40 GHz 16g3A.4 Short Range Devices (SRD) intended for operation in the frequency range 40 GHz to 246 GHz 17g3History 18g3ETSI ETSI EN 301 489-3 V1.6.1 (2013-08) 5Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The informa

17、tion pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ET

18、SI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the upd

19、ates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by

20、 ETSI in response to mandate 284 issued from the European Commission under Directive 98/34/EC i.2 as amended by Directive 98/48/EC i.7. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and reference

21、s of Harmonized Standard under the Directive 1999/5/EC i.1. See article 5.1 of Directive 1999/5/EC i.1 for information on presumption of conformity and Harmonized Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The present documen

22、t is part 3 of a multi-part deliverable. Full details of the entire series can be found in part 1 1. National transposition dates Date of adoption of this EN: 16 August 2013 Date of latest announcement of this EN (doa): 30 November 2013 Date of latest publication of new National Standard or endorsem

23、ent of this EN (dop/e): 31 May 2014 Date of withdrawal of any conflicting National Standard (dow): 31 May 2015 ETSI ETSI EN 301 489-3 V1.6.1 (2013-08) 61 Scope The present document, together with EN 301 489-1 1, covers the assessment of Short Range Devices (SRD) and ancillary equipment in respect of

24、 ElectroMagnetic Compatibility (EMC). Technical specifications related to the antenna port and emissions from the enclosure port of Short Range Devices (SRD) are not included in the present document. Such technical specifications are found in the relevant product standards for the effective use of t

25、he radio spectrum. Examples of SRDs are given in annex A. The present document specifies the applicable test conditions, performance assessment, and performance criteria for Short Range Devices (SRD) and the associated ancillary equipment. In case of differences (for instance concerning special cond

26、itions, definitions, abbreviations) between the present document and the EN 301 489-1 1, the provisions of the present document take precedence. The environmental classification and the emission and immunity requirements used in the present document are as stated in the EN 301 489-1 1, except for an

27、y special conditions included in the present document. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of

28、the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cann

29、ot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. 1 ETSI EN 301 489-1 (V1.9.2) (09-2011): “Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) s

30、tandard for radio equipment and services; Part 1: Common technical requirements“. 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 1999/5/EC of

31、the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz frequency range with power levels ranging up to 5

32、00 mW; Part 1: Technical characteristics and test methods“. ETSI ETSI EN 301 489-3 V1.6.1 (2013-08) 7i.4 ETSI EN 300 330-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment in the frequency range 9 kHz to 25 MHz and inductive loop systems in

33、 the frequency range 9 kHz to 30 MHz; Part 1: Technical characteristics and test methods“. i.5 ETSI EN 300 440-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Short range devices; Radio equipment to be used in the 1 GHz to 40 GHz frequency range; Part 1: Technical characteristics

34、 and test methods“. i.6 ETSI EN 305 550-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 40 GHz to 246 GHz frequency range; Part 1: Technical characteristics and test methods“. i.7 Directive 98/48/EC of the European Parl

35、iament and of the Council of 20 July 1998 amending Directive 98/34/EC laying down a procedure for the provision of information in the field of technical standards and regulations. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions give

36、n in EN 301 489-1 1, clause 3 and the following apply: device type: classification of devices based on the risk assessment of communication link performance receiver: stand alone receiver or receiver being part of a transceiver receiver category: set of relevant receiver requirements and minimum per

37、formance criteria Short Range Device (SRD): piece of apparatus which includes a transmitter, and/or a receiver and or parts thereof, used in alarm, telecommand and telemetry applications, etc. operating with analogue speech/music or data (analogue and/or digital) or with combined analogue speech/mus

38、ic and data, using any modulation type NOTE: These devices can be used in a fixed, mobile or portable application. transmitter: stand alone transmitter or transmitter being part of a transceiver 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AC Alterna

39、ting Current CR Continuous phenomena applied to Receivers CT Continuous phenomena applied to Transmitters DC Direct Current EMC ElectroMagnetic Compatibility EUT Equipment Under Test fo operating frequencyRF Radio Frequency SINAD Ratio of (Signal + Noise + Distortion) to (Noise + Distortion) SRD Sho

40、rt Range Device TR Transient phenomena applied to Receivers TT Transient phenomena applied to Transmitters ETSI ETSI EN 301 489-3 V1.6.1 (2013-08) 84 Test conditions For the purposes of the present document, the test conditions of the EN 301 489-1 1, clause 4, shall apply as appropriate. Further pro

41、duct related test conditions for Short Range Devices (SRD) are specified in the present document. 4.1 General For emission and immunity tests the normal test modulation, test arrangements, etc., as specified in the present document, clauses 4.1 to 4.5, shall apply. Whenever the Equipment Under Test

42、(EUT) is provided with a detachable antenna, the EUT shall be tested with the antenna fitted in a manner typical of normal intended use, unless specified otherwise. For the purpose of the present document Short Range Devices are divided into three types of primary function, based on the technical na

43、ture of the primary function. Table 1: Technical nature of the primary function Primary Function Type Technical nature of the primary function I Transfer of messages (digital or analogue signals) II Transfer of audio (speech or music) III Others 4.2 Arrangements for test signals The provisions of th

44、e EN 301 489-1 1, clause 4.2, shall apply. 4.2.1 Arrangements for test signals at the input of the transmitter The provisions of the EN 301 489-1 1, clause 4.2.1, shall apply with the following modifications. The transmitter shall be modulated with normal test modulation as specified for that type o

45、f primary function (see clause 4.5). Where transmitters do not have a modulation input port, the internal equipment modulation shall be used. 4.2.2 Arrangements for test signals at the output of the transmitter The provisions of the EN 301 489-1 1, clause 4.2.2, shall apply with the following modifi

46、cations. The transmitter shall be operated at its maximum rated RF output power as specified for that type of primary function (see clause 4.5). The manufacturer may provide a suitable companion receiver that can be used to set up a communications link and/or to receive messages. 4.2.3 Arrangements

47、for test signals at the input of the receiver The provisions of EN 301 489-1 1, clause 4.2.3, shall apply with the following modifications: - the wanted RF input signal, coupled to the receiver, shall be modulated with normal test modulation as specified for that type of primary function (see clause

48、 4.5); - the level of the wanted RF input signal shall be chosen to a value significantly above the threshold sensitivity but below the overload characteristics of the receiver; - the manufacturer may provide a suitable companion transmitter that can be used to set up a communications link and/or to

49、 transmit messages. ETSI ETSI EN 301 489-3 V1.6.1 (2013-08) 94.2.4 Arrangements for test signals at the output of the receiver The provisions of EN 301 489-1 1, clause 4.2.4, shall apply. 4.2.5 Arrangements for testing transmitter and receiver together (as a system) The provisions of EN 301 489-1 1, clause 4.2.5, shall apply with the following modification. The transmitter and receiver may be tested together, if appropriate (size of equipment, etc.). In this case the transmitter and the receiver shall be located inside the test envi