EN ISO 10882-1-2011 en Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operator-s breathing zone - Part 1 Sampling of airborne p.pdf
《EN ISO 10882-1-2011 en Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operator-s breathing zone - Part 1 Sampling of airborne p.pdf》由会员分享,可在线阅读,更多相关《EN ISO 10882-1-2011 en Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operator-s breathing zone - Part 1 Sampling of airborne p.pdf(46页珍藏版)》请在麦多课文档分享上搜索。
1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 10882-1:2011Health and safety in weldingand allied processes Sampling of airborne particlesand gases in the operatorsbreathing zonePart 1: Sampling of airborne particle
2、s (ISO10882-1:2011)BS EN ISO 10882-1:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO10882-1:2011. It supersedes BS EN ISO 10882-1:2001 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee WEE/40, Health and safet
3、y in welding.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 56332 4ICS 13.040.30; 13.100;
4、 25.160.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 October 2011.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EU
5、ROPISCHE NORM EN ISO 10882-1 October 2011 ICS 25.160.01; 13.100 Supersedes EN ISO 10882-1:2001English Version Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operators breathing zone - Part 1: Sampling of airborne particles (ISO 10882-1:2011) Hygin
6、e et scurit en soudage et techniques connexes - chantillonnage des particules en suspension et des gaz dans la zone respiratoire des oprateurs - Partie 1: chantillonnage des particules en suspension (ISO 10882-1:2011) Arbeits- und Gesundheitsschutz beim Schweien und bei verwandten Verfahren - Proben
7、ahme von partikelfrmigen Stoffen und Gasen im Atembereich des Schweiers - Teil 1: Probenahme von partikelfrmigen Stoffen (ISO 10882-1:2011) This European Standard was approved by CEN on 30 September 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the c
8、onditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard ex
9、ists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national s
10、tandards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland a
11、nd United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1
12、0882-1:2011: EBS EN ISO 10882-1:2011EN ISO 10882-1:2011 (E) 3 Foreword This document (EN ISO 10882-1:2011) has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes“ in collaboration with Technical Committee CEN/TC 121 “Welding”, the secretariat of which is held by DIN. This E
13、uropean Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2012, and conflicting national standards shall be withdrawn at the latest by April 2012. Attention is drawn to the possibility that some of the elem
14、ents of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 10882-1:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the foll
15、owing countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slov
16、akia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 10882-1:2011 has been approved by CEN as a EN ISO 10882-1:2011 without any modification. BS EN ISO 10882-1:2011ISO 10882-1:2011(E) ISO 2011 All rights reserved iiiContents Page Foreword iv Introduct
17、ion . v 1 Scope 1 2 Normative references 1 3 Terms and definitions . 2 3.1 General definitions 2 3.2 Sampling definitions . 3 3.3 Welding terms 5 3.4 Statistical terms . 7 4 Principle . 8 5 Requirement . 9 6 Equipment 9 6.1 Sampling equipment . 9 6.2 Weighing equipment, if required . 10 7 Assessment
18、 strategy 11 8 Measurement strategy 11 8.1 General . 11 8.2 Personal exposure measurement 11 8.3 Fixed-point measurements . 11 8.4 Selection of measurement conditions and measurement pattern . 12 9 Procedure . 13 9.1 Preliminary considerations 13 9.2 Preparation for sampling 14 9.3 Sampling position
19、 . 15 9.4 Sampling 15 9.5 Transportation . 16 9.6 Analysis 16 9.7 Expression of results 17 10 Exposure assessment . 18 11 Recording of sampling data and presentation of results 18 Annex A (normative) Gravimetric analysis 19 Annex B (informative) Examples of arrangements for mounting samplers behind
20、welders face shields 21 Annex C (informative) An example of a report . 28 Annex D (informative) Blank report form 31 Bibliography 34 BS EN ISO 10882-1:2011ISO 10882-1:2011(E) iv ISO 2011 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of
21、 national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Int
22、ernational organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with t
23、he rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval
24、by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10882-1 was prepared by Technical Committee
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ENISO1088212011ENHEALTHANDSAFETYINWELDINGANDALLIEDPROCESSESSAMPLINGOFAIRBORNEPARTICLESANDGASESINTHEOPERATORSBREATHINGZONEPART1SAMPLINGOFAIRBORNEPPDF
链接地址:http://www.mydoc123.com/p-724219.html