EN ISO 8130-2-2010 en Coating powders - Part 2 Determination of density by gas comparison pyknometer (referee method)《粉末涂料 第2部分 气体比较比重仪法测定密度(仲裁法)》.pdf

《EN ISO 8130-2-2010 en Coating powders - Part 2 Determination of density by gas comparison pyknometer (referee method)《粉末涂料 第2部分 气体比较比重仪法测定密度(仲裁法)》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 8130-2-2010 en Coating powders - Part 2 Determination of density by gas comparison pyknometer (referee method)《粉末涂料 第2部分 气体比较比重仪法测定密度(仲裁法)》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN ISO8130-2:2010Coating powders Part 2: Determination of density by gas comparisonpyknometer (referee method) (ISO 8130-2:1992) ICS 87.040Incorporating corrigendum April 2011National forewordThis British Standard is the UK implementation of EN ISO 8130-2:2010. It is identical to

2、ISO 8130-2:1992. It supersedes BS 3900-J6:1993 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee STI/10, Test methods for paints.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not p

3、urport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN ISO 8130-2:2010This British Standard, having been prepared under the direction of the Pigments, Paint

4、s and Varnishes Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 April 1993 BSI 2011The following BSI references relate to the work on this standard: Committee reference PVC/10 Draft for comment 88/54511 DCAmendments/corrigenda issued s

5、ince publicationDate Comments 30 April 2011 This corigendum renumbers BS 390-J6:193 as BS EN ISO 8130-2:2010ISBN 978 0 580 72110 6EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 8130-2 November 2010 ICS 87.040 English Version Coating powders - Part 2: Determination of density by gas compari

6、son pyknometer (referee method) (ISO 8130-2:1992) Poudres pour revtement - Partie 2: Dtermination de la masse volumique laide dun pycnomtre gaz (mthode de rfrence) (ISO 8130-2:1992) Pulverlacke - Teil 2: Bestimmung der Dichte mit einem Gasvergleichspyknometer (Schiedsverfarhen) (ISO 8130-2:1992) Thi

7、s European Standard was approved by CEN on 16 October 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical refere

8、nces concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member i

9、nto its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, It

10、aly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-10

11、00 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 8130-2:2010: EForeword The text of ISO 8130-2:1992 has been prepared by Technical Committee ISO/TC 35 “Paints and varnishes” of the International Organization for

12、 Standardization (ISO) and has been taken over as EN ISO 8130-2:2010 by Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement

13、, at the latest by May 2011, and conflicting national standards shall be withdrawn at the latest by May 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or

14、all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, H

15、ungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 8130-2:1992 has been approved by CEN as a EN ISO 8130-2:2010 without any mo

16、dification. BS EN ISO 8130-2:2010EN ISO 8130-2:2010 (E) BSI 2011 11 ScopeThis part of ISO8130 specifies a method for the determination of the density of coating powders using a gas comparison pyknometer. It can be used for all types of coating powder, is simple to carry out, but requires more expens

17、ive instrumentation than is often used for density determinations.The density of coating powders can also be determined using the liquid displacement pyknometer method described in ISO8130-3. The apparatus is relatively inexpensive, but the liquid displacement pyknometer method is liable to give err

18、oneous results, particularly if the powder swells in contact with the displacement liquid used or the displacement liquid does not totally displace the air between the powder particles. The liquid displacement method is much slower in execution, less accurate and is only to be used if it can be show

19、n that the same results will be obtained as for the gas comparison pyknometer method.2 Normative referenceThe following standard contains provisions which, through reference in this text, constitute provisions of this part of ISO8130. At the time of publication, the edition indicated was valid. All

20、standards are subject to revision, and parties to agreements based on this part of ISO8130 are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.ISO 842:1

21、984, Raw materials for paints and varnishes Sampling. 3 PrincipleThe volume of a weighed test portion is determined by measuring the volume of gas displaced within a receptacle when the test portion is introduced. This is achieved by equalizing the pressure difference which arises due to the displac

22、ement of the gas. The density is then calculated from the mass and the volume of the test portion.4 Material4.1 Air or, if desired, helium, commercial grade, in a steel cylinder.Other gases may be used provided that the product under test is not affected and this deviation from the method is noted i

23、n the test report.5 Apparatus5.1 Gas comparison pyknometer, for the manual or automatic determination of the density, complying with the requirements given below.The essential design of a typical gas comparison pyknometer using air as the medium is outlined inFigure 1. It consists of two cylinders (

24、A and B) with pistons of exactly equal dimensions. The cylinders are connected by a valve and a pressure difference meter. The test portion, contained in a50ml beaker, is placed in cylinder B. Both pistons are moved by an equal amount which results in a pressure difference between cylinders A and B.

25、 The measuring piston in cylinder B is then moved again to re-establish equal pressure. The resulting volume change, which is equivalent to the volume of the test portion, is read from the scale.The swept volumes of the cylinders shall be measured and shown to be equal to within0,5% (relative). The

26、intervals in the scale showing the measured volume shall not be greater than1% of the measured volume. The scale calibration shall be checked by placing reference standards, of known volume and traceability, in the apparatus. The use of two different volumes is sufficient for routine checks, but at

27、least five different volumes shall be used for the initial calibrations to show that the scale is linear over the whole of its range.NOTE 1Suitable gas comparison pyknometers are available from several manufacturers.6 SamplingTake a representative sample of the product to be tested, as described in

28、ISO842.7 ProcedureCarry out the determination in duplicate at(23 1)C and, where applicable, at a relative humidity of (50 5)%.Adjust the apparatus in accordance with the manufacturers instructions, in particular to allow for the volume of the beaker material. Check the apparatus to ensure that there

29、 are no leaks.Weigh the sample beaker to the nearest1mg and fill it almost to the brim with the product under test, making sure that no powder is on the outside walls of the beaker. Weigh the beaker plus contents to the nearest1mg to determine the mass (m) of the test portion.BS EN ISO 8130-2:2010EN

30、 ISO 8130-2:2010 (E)2 BSI 2011Place the beaker and contents in the apparatus and determine the volume of the test portion by following the instructions given by the manufacturer of the apparatus. Repeat the volume measurement in order to ensure that the reading is consistent and calculate the mean (

31、V) of the two volumes.NOTE 2If the gas is dry, a slight change in density may be observed due to the drying of the test portion.If the two readings differ by more than2%, disregard the results.8 Expression of results8.1 CalculationCalculate the density p, in grams per millilitre, of the coating powd

32、er at23C, using the equation:whereIf the two determinations differ by more than0,04g/ml, repeat the procedure described in clause7.Calculate the mean of two valid determinations and report the result to the nearest0,01g/ml.8.2 PrecisionNo precision data are currently available.9 Test reportThe test

33、report shall contain at least the following information;a) all details necessary to identify the product tested;b) a reference to this part of ISO8130 (ISO8130-2);c) the type of gas comparison pyknometer and the gas used;d) the result of the test (individual values and mean value);e) any deviation f

34、rom the test method specified;f) the date of the test.m is the mass, in grams, of the test portion;V is the volume, in millilitres, of the test portion.P mV-=Figure 1 Example of a gas comparison pyknometerBS EN ISO 8130-2:2010EN ISO 8130-2:2010 (E) BSI 2011List of referencesSee national foreword.BS

35、EN ISO 8130-2:2010EN ISO 8130-2:2010 (E)BSI GroupHeadquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standardsBSI - British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK v

36、iew on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the

37、 quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +

38、44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +

39、44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, u

40、nless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its p

41、roducts and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact

42、Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/ CopyrightCopyright subsists in all BSI publ

43、ications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic,

44、photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager. Tel: +44 (0)20 8996 7070 Email: BS EN ISO 8130-2:2010