EN ISO 6603-2-2000 en Plastics - Determination of Puncture Impact Behaviour of Rigid Plastics - Part 2 Instrumented Puncture Test (Incorporating Corrigendum October 2000)《塑料 硬质塑料复合.pdf

《EN ISO 6603-2-2000 en Plastics - Determination of Puncture Impact Behaviour of Rigid Plastics - Part 2 Instrumented Puncture Test (Incorporating Corrigendum October 2000)《塑料 硬质塑料复合.pdf》由会员分享，可在线阅读，更多相关《EN ISO 6603-2-2000 en Plastics - Determination of Puncture Impact Behaviour of Rigid Plastics - Part 2 Instrumented Puncture Test (Incorporating Corrigendum October 2000)《塑料 硬质塑料复合.pdf（31页珍藏版）》请在麦多课文档分享上搜索。

1、STD=BSI BS EN IS0 bb03-2-ENGL 2000 Lb2YbbS 0913737 571 6 BRITISH STANDARD Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented puncture testing The European Standard EN EO 6603-2:2000 has the status of a British Standard ICs 83.080.01 3s EN IS0 i603-2 :2000

2、ncorpomting hrrigendum No. 1 NO COPYING WITHOUT BSI PFXWISSION EXCEPT AS PERMITTED BY COPYRIGET LAW This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect

3、on 15 December 2000 AmdNo. Date Corrigendum Apd 2001 13063 Q BSI 04-2001 Comments Correction to EN IS0 foreword ISBN O 580 366 80 4 National foreword This British Standard is the official English language version of EN Is0 W22000 including corrigendum October 2000. It is identical with IS0 6603-2200

4、0. It supersedes BS EN Is0 6603-2:1997 which is withdram The UK participation in its preparation was entrusted to Technicd Committee PRv21, Testing of plastics, which has the responsibility to: - aid enquirem to understand the tea - present to the responsible intematiordEuropean committee any enquir

5、es on the interpretation, or proposals for change, and keep the UK interests informed; - monitor related inernatiod and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretaq. Cross-references Attention is

6、 drawn to the fact that CEN and CENELEC Standards nody include an annex which kts normative references to international publications with their corresponding European publications. The British standards which implement international or European publications referred to in this document may be found

7、in the BSI Stan- Catalogue under the section entitled “Intedonal Stan- Correspondence Index“, or by using the “Find“ facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Usem of British Standards are responsibl

8、e for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN IS0 title page, the EN Is0 foreword page, the IS0 title page, pages ii to iv, pages 1 t

9、o 23 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 6603-2 October 2000 _ ICs 08.008.01 Supersedes EN IS0 6603-2:1996 Incorporating corrigendum October 2000 English version Pl

10、astics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented puncture test (IS0 6603-2:2000) Plastiques - Dtermination du comportement des plastiques rigides perfors sous leffet dun choc - Partie 2: Essai de choc instrument (IS0 6603-2:2000) This European Standard was

11、 approved by CEN on 1 October 2000. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nati

12、onal standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and noti

13、fied to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and

14、 United Kingdom. EUROPEAN COMMEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 8-1050 Brussels Q 2000 CEN All rights of exploitation in any form and by any means resewed worldwide for CEN national Members. Ref. No. EN IS0 6

15、603-2:2000 E STDmBSI BS EN IS0 bb03-2-ENGL 2000 Zb24bb9 09LL712 Obb EN IS0 6603-2:2000 Foreword The text of the International Standard IS0 6603-2:2000 has been prepared by Technical Committee ISOTTC 198 Plastics in collaboration with Technical Committee CENTTC 249 Plastics, the Secretariat of which

16、is held by IBN. This European Standard replaces EN IS0 6603-2:1996. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2000, and conflicting national standards shall be withdrawn at the late

17、st by April 2001. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherl

18、ands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard IS0 6603-2:2000 was approved by CEN as a European Standard without any modification. STD-BSI BS EN IS0 bb03-2-ENGL 2000 1b24bb7 0911713 TT2 EN IS0 6603-2:2000 INTERNAT

19、IONAL IS0 STANDARD 6603-2 Second edition 2000-1 0-01 Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented impact testing Plastiques - Dtermination du comportement des plastiques rigides perfors sous reffet dun choc - Partie 2: Essais de choc instruments Refe

20、rence number IS0 6603-2:2000(E) STD*BSI BS EN IS0 bb03-2-ENGL 2000 m Zb24bb7 07Z17Li 739 m EN IS0 6603-2:2000 Contents Page Foreword . iv 1 Scope 1 2 Normative references 1 3 4 Principle 5 5 Apparatus . 5 6 Test specimens 9 7 Procedure . 9 8 Calculations 10 Terms and definitions . 1 9 Precision . 12

21、 Test report 12 Annex A (informative) Interpretation of complex force-deflection curves 14 1 O Annex B (informative) Friction between striker and specimen 16 Annex C (informative) Clamping of specimens 19 Annex D (informative) Toughhrittle transitions . 20 Annex E (informative) Influence of specimen

22、 thickness . 21 Bibliography 23 . 111 - STDVBSI BS EN IS0 bb03-2-ENGL 2000 lb24bb9 0911715 875 = EN IS0 6603-2:2000 Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standa

23、rds is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that cornmittee. International organizations, governmental and non-governmental, in liaison with ISO, also ta

24、ke part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISOAEC Directives, Part 3. Draft International Standards adopted by

25、 the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of IS0 6603 may be the subject of pa

26、tent rights. IS0 shall not be held responsible for identifying any or all such patent rights. International Standard IS0 6603-2 was prepared by Technical Committee ISOTTC 61, Plastics, Subcommittee SC 2, Mechanical properties. This second edition cancels and replaces the first edition (IS0 6603-2:19

27、89), which has been technically revised. IS0 6603 consists of the following parts, under the general title Plastics - Determination of puncture impact behaviour of rigid plastics: - Part 1 : Non-instrumented impact testing - Part 2: Instrumented impact testing Annexes A to E of this part of IS0 6603

28、 are for information only. iv STD-BSI BS EN IS0 bb03-2-ENGL 2000 lb24bb9 07LL7Lb 701 = EN IS0 6603-2:ZOOO Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented impact testing 1 Scope This part of IS0 6603 specifies a test method for the determination of punct

29、ure impact properties of rigid plastics, in the form of flat specimens, using instruments for measuring force and deflection. It is applicable if a force-deflection or force-time diagram, recorded at nominally constant striker velocity, is necessary for detailed characterization of the impact behavi

30、our. IS0 6603-1 can be used if it is sufficient to characterize the impact behaviour of plastics by a threshold value of impact-failure energy based on many test specimens. It is not the purpose of this part of IS06603 to give an interpretation of the mechanism occurring on every particular point of

31、 the force-deflection diagram. These interpretations are a task for scientific research. NOTE See also clause 1 of IS0 6603-1:2000. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of IS0 6603. For d

32、ated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of IS0 6603 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated

33、 references, the latest edition of the normative document referred to applies. Members of IS0 and IEC maintain registers of currently valid International Standards. IS0 2602:1980, Statistical interpretation of test results - Estimation of the mean - Confidence interval. IS0 6603-1 :2000, Plastics -

34、Determination of puncture impact behaviour of rigid plastics - Part 7: Non- instrumented impact testing. 3 Terms and definitions For the purposes of this part of IS0 6603, the following terms and definitions apply. 3.1 impact velocity “O velocity of the striker relative to the support at the moment

35、of impact NOTE Impact velocity is expressed in metres per second (m/s). 1 3.2 force F force exerted by the striker on the test specimen in the direction of impact NOTE Force is expressed in newtons (N). 3.3 deflection 1 relative displacement between the striker and the specimen support, starting fro

36、m the first contact between the striker and the test specimen NOTE Deflection is expressed in millimetres (mm). 3.4 energy E energy expended in deforming and penetrating the test specimen up to a deflection 1 NOTE 1 Energy is expressed in joules (J). NOTE 2 Energy is measured as the integral of the

37、force-deflection curve starting from the point of impact up to a deflection 1. 3.5 maximum force FM maximum force occurring during the test See Figures 1 to 4. NOTE Maximum force is expressed in newtons (N). 3.6 deflection at maximum force lM deflection that occurs at maximum force FM See Figures 1

38、to 4. NOTE Deflection at maximum force is expressed in millimetres (mm). 3.7 energy to maximum force EM energy expended up to the deflection l at maximum force See Figures 1 to 4. NOTE Energy to maximum force is expressed in joules (J). 3.8 puncture deflection 1P deflection at which the force has dr

39、opped to half the maximum force FM See Figures 1 to 4 and note to 3.9. NOTE Puncture deflection is expressed in millimetres (mm). 2 STD-BSI BS EN IS0 bb03-2-ENGL 2000 D Lb24bb7 07LL7L8 584 E EN IS0 6603-2:2000 3.9 puncture energy EP energy expended up to the puncture deflection Ip See Figures 1 to 4

40、 and note 2. NOTE 1 Puncture energy is expressed in joules (J). NOTE 2 When testing tough materials, a transducer mounted at some distance from the impacting tip may record frictional force acting between the cylindrical pait of the striker and the punctured material. The corresponding frictional en

41、ergy shall not be included in the puncture energy, which, therefore, is restricted to that deflection, at which the force drops to half the maximum force FM 3.10 impact failure mechanical behaviour of the material under test which may be either one of the following types (see note): a) YD b) YS c) Y

42、U yielding (zero slope at maximum force) followed by deep drawing yielding (zero slope at maximum force) followed by (at least partially) stable cracking yielding (zero slope at maximum force) followed by unstable cracking d) NY no yielding See Figures 1 to 4. NOTE Comparison of Figures 2 and 3 show

43、s puncture deflection lp and puncture energy Ep are identical for the failure types YS and YU. As shown in Figure 4, identical values at maximum and at puncture are found for the deflection as well as the energy in the case of failure type YU. For complex behaviour see annex A. 1/2 L O LL FM t Defle

44、ction Figure 1 - Example of force-deflection diagram for failure by yielding (zero slope at maximum force) followed by deep drawing, and typical appearance of specimens after testing (with lubrication) 3 STDDBSI BS EN IS0 bbD3-2-ENGL 2000 W Lb24bL7 U7LL7L7 Liz0 0 EN IS0 6603-22000 FM 1/2 FM Y Deflec

45、tion Figure 2 - Example of forcedeflection diagram for failure by yielding (zero slope at maximum force) followed by stable crack growth, and typical appearance of specimens after testing (with lubrication) al U L O LI 1/2 FM NOTE Natural vibration of the force detector can be seen after unstable cr

46、acking (striker and load cell). Figure 3 - Example of forcedeflection diagram for failure by yielding (zero slope at maximum force) followed by unstable crack growth, and typical appearance of specimens after testing (with lubrication) 4 EN IS0 6603-2:2000 ln Ip Deflection Figure 4 - Example of forc

47、e-deflection diagram for failure without yielding followed by unstable crack growth, and typical appearance of specimens after testing (with lubrication) 4 Principle The test specimen is punctured at its centre using a lubricated striker, perpendicularly to the test-specimen surface and at a nominal

48、ly uniform velocity. The resulting force-deflection or force-time diagram is recorded electronically. The test specimen may be clamped in position during the test. The force-deflection diagram obtained in these tests records the impact behaviour of the specimen from which several features of the beh

49、aviour of the material may be inferred. 5 Apparatus 5.1 Testing device, consisting of the following essential components: - energy carrier, which may be inettial-mass type or hydraulic type (see 5.1 .l); - striker, which shall be lubricated; - specimen support with a recommended clamping device. The test device shall permit the test specimen to be punctured at its centre, perpendicular to its surface at a nominally constant velocity. The force exerted on the test specimen in the direction of impact and the deflection from the centre of the test specimen