EN 61755-3-7-2009 en Fibre optic interconnecting devices and passive components - Fibre optic connector optical interfaces - Part 3-7 Optical interface 2 5 mm and 1 25 mm diameter .pdf

《EN 61755-3-7-2009 en Fibre optic interconnecting devices and passive components - Fibre optic connector optical interfaces - Part 3-7 Optical interface 2 5 mm and 1 25 mm diameter .pdf》由会员分享，可在线阅读，更多相关《EN 61755-3-7-2009 en Fibre optic interconnecting devices and passive components - Fibre optic connector optical interfaces - Part 3-7 Optical interface 2 5 mm and 1 25 mm diameter .pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI British StandardsWB9423_BSI_StandardColCov_noK_AW:BSI FRONT COVERS 5/9/08 12:55 Page 1Fibre optic interconnectingdevices and passive components Fibre opticconnector optical interfaces Part 3-7: Optic

2、al interface, 2,5 mm and 1,25 mmdiameter cylindrical PC composite ferrule using titanium as fibre surrounding material, single mode fibreBS EN 61755-3-7:2009National forewordThis British Standard is the UK implementation of EN 61755-3-7:2009. It isidentical to IEC 61755-3-7:2009.The UK participation

3、 in its preparation was entrusted by Technical CommitteeGEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre optic interconnectingdevices and passive components.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to incl

4、ude all the necessary provisions of acontract. Users are responsible for its correct application. BSI 2009ISBN 978 0 580 59157 0ICS 33.180.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy

5、and Strategy Committee on 30 September 2009Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 61755-3-7:2009EUROPEAN STANDARD EN 61755-3-7 NORME EUROPENNE EUROPISCHE NORM April 2009 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Norm

6、alisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: avenue Marnix 17, B - 1000 Brussels 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61755-3-7:2009 E ICS 33.180.20 English versi

7、on Fibre optic interconnecting devices and passive components - Fibre optic connector optical interfaces - Part 3-7: Optical interface, 2,5 mm and 1,25 mm diameter cylindrical PC composite ferrule using titanium as fibre surrounding material, single mode fibre (IEC 61755-3-7:2009) Dispositifs dinter

8、connexion et composants passifs fibres optiques - Interfaces optiques de connecteurs pour fibres optiques - Partie 3-7: Interfaces optiques, frules composites cylindriques PC, de diamtre 2,5 mm et 1,25 mm, utilisant le titane comme matriau entourant la fibre, fibres unimodales (CEI 61755-3-7:2009) L

9、ichtwellenleiter -Verbindungselemente und passive Bauteile - Optische Schnittstellen von Lichtwellenleiter-Steckverbindern - Teil 3-7: Optische Schnittstelle - Zylindrische PC-Composite-Ferrulen mit 2,5 mm und 1,25 mm Durchmesser fr Einmodenfaser, mit Titan als Material fr die Faserfassung, Einmoden

10、 LWL (IEC 61755-3-7:2009) This European Standard was approved by CENELEC on 2009-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date

11、lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under th

12、e responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France,

13、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 61755-3-7:2009EN 61755-3-7:2009 2 Foreword The text of document 86B/2768/FDIS, fut

14、ure edition 1 of IEC 61755-3-7, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61755-3-7 on 2009-03-01. The following dates were fixed: latest date by which t

15、he EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2009-12-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2012-03-01 _ Endorsement notice The text of the International Standard IEC

16、61755-3-7:2009 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61753-1 NOTE Harmonized as EN 61753-1:2007 (not modified). IEC 61755-3 NOTE Harmonized in EN 61755-

17、3 series (modified). _ BS EN 61755-3-7:2009 2 61755-3-7 IEC:2009 CONTENTS 1 Scope.5 2 Description .5 3 Interface parameters for PC ferrule independent from the ferrule material 6 Annex A (informative) .9 Bibliography10 Figure 1 Interface dimensions for PC ferrule 6 Figure 2 Fibre core location .6 Fi

18、gure 3 Interface dimension of the end-face contact zone.7 Table 1 Optical interface parameter values for 2,5 mm diameter PC ferrule .7 Table 2 Optical interface parameter values for 1,25 mm diameter PC ferrule .8 BS EN 61755-3-7:200961755-3-7 IEC:2009 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIV

19、E COMPONENTS FIBRE OPTIC CONNECTOR OPTICAL INTERFACES Part 3-7: Optical interface, 2,5 mm and 1,25 mm diameter cylindrical PC composite ferrule using titanium as fibre surrounding material, single mode fibre 1 Scope This part of IEC 61755 defines dimensional limits and material properties of a 2,5 m

20、m and a 1,25 mm diameter cylindrical composite ferrule optical interface to meet specific requirements for PC fibre-to-fibre interconnection. The composite ferrule uses different materials in the end face contact zone and in ferrule to sleeve contact zone. The specified materials for each zone are z

21、irconia (ZrO2) for the ferrule to sleeve contact zone and titanium for the end face contact zone. Ferrules made from the material specified in this standard are suitable for use in categories C, U, E and O as defined in IEC 61753-1. NOTE If mated within the same family (cylindrical PC ferrule), the

22、ferrules specified in this standard are intended to have the same optical attenuation performance grade for connections with all ferrules described in different parts of IEC 61775-3. 2 Description The performance of a cylindrical ferrule optical interface is determined by the accuracy with which the

23、 optical datum targets of two mating ferrules are aligned with each other. There are three conditions affecting the alignment of two optical datum targets, lateral offset, angular offset and longitudinal offset. Parameters influencing the lateral and angular offset of the optical fibre axes include

24、the following: ferrule outside diameter; fibre hole concentricity relative to the ferrule outside diameter; fibre hole angle relative to outside diameter axis; fibre cladding diameter to fibre hole clearance; alignment sleeve inside diameter; fibre core concentricity relative to the cladding diamete

25、r; fibre core orientation relative to keying feature. Parameters influencing the longitudinal offset of the optical fibre axes include the following: end face spherical radius; end face spherical radius apex offset; fibre undercut; axial force on ferrule end face; ferrule and fibre material physical

26、 constants; alignment sleeve frictional force. BS EN 61755-3-7:2009 6 61755-3-7 IEC:2009 3 Interface parameters for PC ferrule independent from the ferrule material No sharp edge K D J Ferrule axis Fibre axis E IEC 2295/08 Figure 1 Interface dimensions for PC ferrule FIEC 1315/06 Figure 2 Fibre core

27、 location F defines the radial coordinate limits of the optical fibre core relative to the optical datum of the ferrule. BS EN 61755-3-7:200961755-3-7 IEC:2009 7 CAB IEC 2113/06 Figure 3 Interface dimension of the end-face contact zone Table 1 Optical interface parameter values for 2,5 mm diameter P

28、C ferrule Parameter values Grade A Grade B Grade C Grade D Remarks Ref. Minimum Maximum Minimum Maximum Minimum Maximum Minimum Maximum A 200 a200 a200 ab, nm B 7 20 7 20 7 20 Radius, mm C 0 70 0 70 0 70 m D 2,4985 2,4995 2,4985 2,4995 2,4985 2,4995 Diameter, mm E 0 0,6 0 0,8 0 0,6 Degrees F 0 0,000

29、15 0 0,0003 0 0,0016 Radius, mm J 0,8 - 0,8 - 0,8 - Diameter, mm K - 1,8 - 1,8 - 1,8 mm aContact force 4,9 N minimum. Ferrule material: titanium. Nominal material physical constant values: Youngs Modulus, E = 105 GPa, Poissons Ratio, = 0,34. ()801010102115326267650Maximum+=CBBB,bA negative value ind

30、icates fibre protrusion. BS EN 61755-3-7:2009 8 61755-3-7 IEC:2009 Table 2 Optical interface parameter values for 1,25 mm diameter PC ferrule Parameter Values Grade A Grade B Grade C Grade D Remarks Ref. Minimum Maximum Minimum Maximum Minimum Maximum Minimum Maximum A -200 a-200 a-200 ab, nm B 7 20

31、 7 20 7 20 Radius, mm C 0 70 0 70 0 70 m D 1,2485 1,2495 1,2485 1,2495 1,2485 1,2495 Diameter, mmE 0 0,6 0 0,8 0 0,6 Degrees F 0 0,00015 0 0,0003 0 0,0016 Radius, mm J 0,6 - 0,6 - 0,6 - Diameter, mmK - 1,0 - 1,0 - 1,0 mm aContact force 2,9 N minimum. Ferrule material: titanium. Nominal material phys

32、ical constant values: Youngs Modulus, E = 105 GPa, Poissons Ratio, = 0,34. ()801010101880326267650Maximum+=CBBB,bA negative value indicates fibre protrusion. BS EN 61755-3-7:200961755-3-7 IEC:2009 9 Annex A (informative) Maximum allowed spherical fibre undercut The maximum allowed spherical fibre un

33、dercut AMaximumis determined by the interaction of the parameters influencing the longitudinal offset of the optical fibre axes as defined by A.1. PFWDTE32626k1Maximum101010 2DDCBBBkA +=A.1where AMaximumis the maximum spherical undercut for physical contact (nm); k1is the coefficient based on ferrul

34、e contact force and material properties; k2is the exponent based on ferrule contact force and material properties; B is the end face spherical radius (mm); C is the apex offset from fibre axis (m); DDTEis the differential thermal expansion between the ferrule material and the silica fibre at maximum

35、 operating temperature (nm). DDTEbetween the Ti-composite ferrule material and the silica fibre at maximum operating temperature is 50 nm; DPFWis the permanent fibre withdrawal that exceeds the transient fibre movement predicted by the first three terms in A.1 (nm). DPFWfor the Ti-composite ferrule

36、is 30 nm. End face deformation term as a function of contact force, end face radius and material properties. 21kBk A.2 Geometric compensation term for the offset of the ferrule apex from the fibre axis. 32626101010 + CBB A.3 BS EN 61755-3-7:2009 10 61755-3-7 IEC:2009 Bibliography IEC 61753-1, Fibre

37、optic interconnecting devices and passive components performance standard Part 1: General and guidance for performance standards IEC 61755-3 (all parts), Fibre optic connector optical interfaces Part 3: Optical interface _ BS EN 61755-3-7:2009This page deliberately left blankThis page deliberately l

38、eft blankBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswi

39、ck High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products andservices. We w

40、ould be grateful if anyone finding an inaccuracy orambiguity while using this British Standard would inform the Secretary ofthe technical committee responsible, the identity of which can be foundon the inside front cover.Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400BSI offers members an individu

41、al updating service called PLUS whichensures that subscribers automatically receive the latest editions ofstandards.Buying standardsOrders for all BSI, international and foreign standards publicationsshould be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email:

42、 You may also buy directly using a debit/credit card from the BSI Shopon the website response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provide

43、s a wide range of information on national, European andinternational standards through its Library.Various BSI electronic information services are also available which givedetails on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Emai

44、l: Subscribing members of BSI are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact MembershipAdministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding

45、online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of thepublications of the international standardization bodies. Except a

46、s permitted under theCopyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrievalsystem or transmitted in any form or by any means electronic, photocopying, recording orotherwise without prior written permission from BSI. This does not preclude the free use, in the cou

47、rse of implementing the standard of necessarydetails such as symbols, and size, type or grade designations. If these details are to be used forany other purpose than implementation then the prior written permission of BSI must beobtained. Details and advice can be obtained from the Copyright & Licensing Manager.Tel: +44 (0)20 8996 7070 Email: WB9423_BSI_StandardColCov_noK_AW:BSI FRONT COVERS 5/9/08 12:55 Page 2