EN 61300-2-10-2012 en Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-10 Tests - Crush resistance.pdf

《EN 61300-2-10-2012 en Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-10 Tests - Crush resistance.pdf》由会员分享，可在线阅读，更多相关《EN 61300-2-10-2012 en Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-10 Tests - Crush resistance.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationFibre optic interconnectingdevices and passive component Basic test and measurement proceduresPart 2-10: Tests Crush resistanceBS EN 61300-2-10:2012National forewordThis British

2、Standard is the UK implementation of EN 61300-2-10:2012. It isidentical to IEC 61300-2-10:2012. It supersedes BS EN 61300-2-10:1997which is withdrawn.The UK participation in its preparation was entrusted by Technical CommitteeGEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre optic interconnectin

3、gdevices and passive components.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users are responsible for its correct application. The British Standards Institutio

4、n 2013Published by BSI Standards Limited 2013ISBN 978 0 580 69777 7ICS 33.180.20Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and Strategy Committee on 31 January 2013.Amendments issued s

5、ince publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 61300-2-10:2012EUROPEAN STANDARD EN 61300-2-10 NORME EUROPENNE EUROPISCHE NORM November 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektro

6、technische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61300-2-10:2012 E ICS 33.180.20 Supersedes EN 61300-2-10:1997English version Fibre optic interconnectin

7、g devices and passive components - Basic test and measurement procedures - Part 2-10: Tests - Crush resistance (IEC 61300-2-10:2012) Dispositifs dinterconnexion et composantspassifs fibres optiques - Mthodes fondamentales dessais et de mesures - Partie 2-10: Essais - Rsistance la compression (CEI 61

8、300-2-10:2012) Lichtwellenleiter -Verbindungselemente und passive Bauteile - Grundlegende Prf- und Messverfahren - Teil 2-10: Prfungen - Querdruckbestndigkeit (IEC 61300-2-10:2012) This European Standard was approved by CENELEC on 2012-09-13. CENELEC members are bound to comply with the CEN/CENELEC

9、Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to

10、 any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the

11、 official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembo

12、urg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 61300-2-10:2012EN 61300-2-10:2012 - 2 - Foreword The text of document 86B/3439/FDIS, future edition 2 of IEC 61300-2-10, prepared by SC 86B “Fibre opti

13、c interconnecting devices and passive components“ of IEC/TC 86 “Fibre optics“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-10:2012. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an id

14、entical national standard or by endorsement (dop) 2013-06-13 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2013-09-13 This document supersedes EN 61300-2-10:1997. EN 61300-2-10:2012 includes the following significant technical changes with respe

15、ct to EN 61300-2-10:1997: The changes with respect to the previous edition are to reconsider the entire text. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or

16、all such patent rights. Endorsement notice The text of the International Standard IEC 61300-2-10:2012 was approved by CENELEC as a European Standard without any modification. BS EN 61300-2-10:2012- 3 - EN 61300-2-10:2012 Annex ZA (normative) Normative references to international publications with th

17、eir corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (in

18、cluding any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 61300-1 - Fibre optic interconnecting devices and passive components - Basic test and measurement p

19、rocedures - Part 1: General and guidance EN 61300-1 - IEC 61300-2-38 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-38: Tests - Sealing for pressurized fibre optic closures EN 61300-2-38 - IEC 61300-3-1 - Fibre optic interconnecting devi

20、ces and passive components - Basic test and measurement procedures - Part 3-1: Examinations and measurements - Visual examination EN 61300-3-1 - IEC 61300-3-4 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-4: Examinations and measurement

21、s - Attenuation EN 61300-3-4 - IEC 61300-3-6 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-6: Examinations and measurements - Return loss EN 61300-3-6 - BS EN 61300-2-10:2012 2 61300-2-10 IEC:2012 CONTENTS 1 Scope . 5 2 Normative refere

22、nces . 5 3 General description 5 4 Apparatus . 5 4.1 General . 5 4.2 Plate . 5 4.3 Pad . 6 4.4 Force generator . 6 4.5 Gauge . 6 5 Procedure. 6 5.1 DUT preparation 6 5.2 Pre-conditioning 6 5.3 Initial measurements . 6 5.4 Device mounting 7 5.5 Conditioning 7 5.6 Final examinations and measurements 7

23、 6 Severity 7 7 Details to be specified 7 Figure 1 Apparatus 6 Table 1 Severities 7 BS EN 61300-2-10:201261300-2-10 IEC:2012 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 2-10: Tests Crush resistance 1 Scope This part of IEC 61300 evaluates t

24、he effect of loads which might occur when fibre optic devices are exposed to critical situations such as being stepped on or being run over by vehicle tyres. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its

25、 application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61300-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 1: General

26、and guidance IEC 61300-2-38, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-38: Tests Sealing for pressurized fibre optic closures IEC 61300-3-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures

27、Part 3-1: Examinations and measurements Visual examination IEC 61300-3-4, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-4: Examinations and measurements Attenuation IEC 61300-3-6, Fibre optic interconnecting devices and passive components Bas

28、ic test and measurement procedures Part 3-6: Examinations and measurements Return loss 3 General description The device under test (DUT) is exposed to a compressive load which is applied by a pad. 4 Apparatus 4.1 General The apparatus consists of the following elements (Figure 1). 4.2 Plate A 10 mm

29、thick steel plate large enough for the whole DUT or as specified in the relevant specification. The plate is place on a non yielding surface. The plate has rounded edges. BS EN 61300-2-10:2012 6 61300-2-10 IEC:2012 4.3 Pad A 10 mm thick steel pad, size as Table 1, or as specified in the relevant spe

30、cification, bonded to a non-yielding plate. The pad has rounded edges. 4.4 Force generator The force generator may be any device or apparatus capable of smoothly applying the specified load at the specified rate. 4.5 Gauge A suitable instrument for measuring the load applied to the DUT. Key 1 force

31、generator and gauge 2 pad 3 device under test 4 plate Figure 1 Apparatus 5 Procedure 5.1 DUT preparation Prepare the DUT in accordance with the relevant specification. Unless otherwise specified, the DUT shall be subjected to the crush resistance test in a non-operational mode. Clean the optical and

32、 mechanical parts of the DUT according to the manufacturers instructions. 5.2 Pre-conditioning Unless otherwise specified, pre-condition each prepared closure DUT for 4 h and each prepared connector DUT for 2 h at the standard test conditions specified in IEC 61300-1. 5.3 Initial measurements The DU

33、T shall be visually inspected, optically measured and mechanically checked as required by the relevant specification. 4 1 3 2 IEC 1602/12 BS EN 61300-2-10:201261300-2-10 IEC:2012 7 5.4 Device mounting Position the DUT centrally on the test surface contained in the shallow box. 5.5 Conditioning a) Pl

34、ace the pad over the DUT. b) Smoothly apply the specified load to the pad. c) Maintain the load for the specified duration. 5.6 Final examinations and measurements Upon completion of the test, the DUT shall be examined and all necessary observations recorded as specified in the relevant specificatio

35、n. Careful attention shall be given to the loss of optical continuity (where tested, use IEC 61300-3-4 and IEC 61300-3-6), broken parts (IEC 61300-3-1), and damage to seals (IEC 61300-2-38). 6 Severity The severity consists of the combination of the load, load area and the duration. The severity sha

36、ll be specified in the relevant specification or taken from the table below. Table 1 Severities Severity Load N Pad area Duration s Closures 1 000 50 25 cm2600 Connectors for industrial environment 750 50 25 cm260 7 Details to be specified The following details, as applicable, shall be specified in

37、the relevant specification: Representative ground or floor surface Load Duration of load DUT orientation DUT optically functioning or non-functioning DUT mated or unmated Pre-conditioning procedure Number of load applications Post-conditioning procedure Initial examinations and measurements and perf

38、ormance requirements Examinations and measurements during test and performance requirements _ BS EN 61300-2-10:2012This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publicatio

39、ns, information and services. It presents the UK view on standards in Europe and at the international level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwid

40、eBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improv

41、e the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify

42、 BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 70

43、01Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 89

44、96 7001Email: In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards th

45、rough its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. T

46、el: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all

47、 British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as

48、 permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI