EN 60634-1995 en Heat Test Source (H T S ) Lamps for Carrying out Heating Tests on Luminaires《灯具热试验用热试验源(H T S)灯(IEC 634-1993)［替代 CENELEC HD 392 S2］》.pdf

《EN 60634-1995 en Heat Test Source (H T S ) Lamps for Carrying out Heating Tests on Luminaires《灯具热试验用热试验源(H T S)灯(IEC 634-1993)［替代 CENELEC HD 392 S2］》.pdf》由会员分享，可在线阅读，更多相关《EN 60634-1995 en Heat Test Source (H T S ) Lamps for Carrying out Heating Tests on Luminaires《灯具热试验用热试验源(H T S)灯(IEC 634-1993)［替代 CENELEC HD 392 S2］》.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、 CENELEC EN*bOb3Y 95 m 3Y04583 OL5577b 8TT m BRITISH STANDARD Heat test source (H.T.S.) lamps for carrying out heating tests on luminaires UDC 628.94: .U2 1.316.58.Ol7.7 1 O83 B;! 1,326.7.089. 2-65.00 1.2 BS EN 60634 : 1995 CENELEC ENmbOb34 95 = 340Li583 0355777 73b BS EN 60634 : 1995 Amd. No. Commi

2、ttees responsible for this British Standard Date Text affected The preparation of this British Standard was entrusted to Technical Committee CPLI3411, Lamps, upon which the following bodies were represented: British Lighting Association for the Preparation of Standards Chartered Institution of Build

3、ing Services Engineers Electricity Association Engineering Equipment and Materials Users Association Institution of Lighting Engineers Lighting Industry Federation Ltd. London Regional Transport National Illumination Committee of Great Britain Society of Motor Manufacturers and Traders Limited (BRIT

4、LAPS) This British Standard, having been prepared under the direction of the Electrotechnicai Sector Board, was published under the authority of the Standards Board and comes into effect on 15 July 1995 O BSI 1995 The following BSI references relate to the work on this standard: Committee reference

5、CPL/34/1 Draft for comment 91/20221 DC ISBN O 580 24317 6 Amendments issued since publication CENELEC EN*bb34 95 3404583 0155778 672 a BS EN 60634 : 1995 Contents Page Committees responsible Inside front cover National foreword ii Fore word 2 Text of EN 60634 3 i National foreword This British Stand

6、ard has been prepared by Technical Committee CPL/34/1 and is the English language version of EN 60634 : 1995 Heat test source (H. T.S.) lamps for carrying out heating tests on luminaires, published by the European Committee for Electrotechnical Standardization (CENELEC). It is identical to IEC 634 :

7、 1993 published by the International Electrotechnical Commission (IEC), which has the same title as the European Standard. The foreword of the EN makes reference to the date of withdrawal (dow) of the relevant national standard. In this case the relevant standard is BS 6012 : 1980 which will be with

8、drawn on 1995-12-01. Certificates or marks will not be awarded after this date with respect to the withdrawn British Standard. However, such certificates and marks, already awarded, may apply to production until 2000-12-01. The following print types are used in this standard: requirement proper in r

9、oman type test specijkations in italic type expanatory matter in smaller roman type Cross-references international standard EN 60630 : 1989 (IEC 360 : 1987) EN 60432-1 : 1995l) (IEC 432-1 : 1993) EN 60598-1 : 1993 (IEC 598-1 : 1992) IEC 887 Corresponding British Standard BS 5371 : 1990 Standard meth

10、od of measurmnt of lamp cap temperature rise BS EN 60432 Safety specflication for incandescent lamps Part 1 : 1995 Tungsten filament lamps for domestic and similar general lighting purposes BS EN 60598 Luminaires Part 1 : 1993 General requirements and tests BS 7132 : 1989 Nomenclature for ghs bulb d

11、esignation system for lamps Compliance with a British Standard does not of itself confer immunity from legal obligations. 1 EN 60432 : 1988 has been superseded by EN 60432-1 : 1995. ii CENELEC EN*bb34 95 3404583 0355780 220 = EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60634 January 1995 UD

12、C 628.94:621.316.58.017.71.083 621.326.7.089.62-65.001.2 ICs 29.140.40 Supersedes HD 392 S2 : 1985 Descriptors: Luminaires, temperature rise of lampholders, measurement, heat test source lamp, requirements English version Heat test source (H.T.S.) lamps for carrying out heating tests on luminaires (

13、IEC 634 : 1993) Lampes talons pour essais dchauffement (E. E. E.) excuter sur les luminaires (CE1 634 : 1993) Leuchten Wrmeprflampen (HTS-Lampen) zur Durchfhrung von Erwrmungsprfungen an (IEC 634 : 1993) This European Standard was approved by CENELEC on 1994-12-06. CENELEC members are bound to compl

14、y with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secre

15、tariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as t

16、he official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electro

17、technical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels O 1995 Copyright reserved to CENELEC members Ref. No. EN 60634 : 1995 E CENELEC EN+bb34 95 3404583 OL5578L Lb7 Page 2 EN

18、 60634 : 1995 Foreword The text of the International Standard IEC 634 : 1993, prepared by SC 34A, Lamps, of IEC E 34, Lamps and related equipment, was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 60634 on 1994- 12-06 without any modification. The following dates wer

19、e fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by latest date by which the national standards conflicting with the EN have to be withdrawn endorsement (dop) 1995- 12-0 I - (dow) 1995-12-01 For products which have com

20、plied with HD 392 S2 : 1985 before 1995-12-01, as shown by the manufacturer or by a certification body, this previous standard may continue to apply for production until 2000-12-01. Annexes designated normative are part of the body of the standard. In this standard, annexes A, B and ZA are normative

21、. Annex ZA has been added by CENELEC. CENELEC ENmbOb34 95 E 3404583 0155782 OT3 E Page 3 EN 60634 : 1995 CONTENTS page FOREWORD 2 Clause Scope 4 Normative references 4 Definitions . 4 General requirements . 5 Requirements for H.T.S. lamps for thermal tests on luminaires for incandescent lamps . 5 An

22、nexes A Survey of the origin and development of heat test source lamps . 8 6 Scheme of the fundamental system . 1 O ZA (normative) Other international publications quoted in this standard with the references of the relevant European publications 11 CENELEC EN*bOb3Y 95 W 3Li04583 0155783 T3T W Page 4

23、 EN 60634 : 1995 HEAT TEST SOURCE (H.T.S.) LAMPS FOR CARRYING OUT HEATING TESTS ON LUMINAIRES 1 Scope This International Standard specifies requirements for heat test source (H.T.S.) lamps used for carrying out those thermal tests of IEC 598 which primarily check the influence of heat conducted thro

24、ugh the lamp cap as well as of convection. For a description of the origin and philosophy of this standard see annex A. Where H.T.S. lamps are not available, an alternative heat test source (A.H.T.S.) lamp may be used. A guideline for the selection and preparation of such lamps is given in annex B o

25、f IEC 598-1. Some consideration has been given to radiation test sources (R.T.S.) in annex A. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editi

26、ons indicated were valid. All normative documents are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. Members of IEC and IS0 maintain reg

27、isters of currently valid International Standards. IEC 360: 1987, Standard method of measurement of lamp cap temperature rise IEC 432: 1984, Safety requirements for tungsten filament lamps for domestic and similar general lighting purposes IEC 598, Luminaires IEC 598-1 : 1992, Luminaires - Part I: G

28、eneral requirements and tests IEC 887: 1988, Glass bulb designation system for lamps 3 Definitions For the purpose of this International Standard, the following definitions apply. CENELEC EN*hh34 95 3404583 0355784 976 Page 5 EN 60634 : 1995 3.1 heat test source (H.T.S.): Lamp which has a cap temper

29、ature rise (At,) equal to the maximum permissible cap temperature rise (At, max.) as specified for the specific lamp type in the appropriate table of IEC 432. 3.2 alternative heat test source (A.H.T.S.): Commercial lamp which has a cap temperature rise (At,) in the range 5 K below, up to the maximum

30、 permissible cap temperature rise (At, max.), as specified for the specific lamp type in the appropriate table of IEC 432. NOTE - Under consideration for 100 V lamps. 3.3 radiation test source (R.T.S.): Commercial lamp which reproduces the most onerous situation regarding radiation for this type of

31、lamp. 4 General requirements The lamp cap temperature rise shall be referred to an ambient temperature of 25 OC and shall be measured as specified in IEC 360. 5 Requirements for H.T.S. lamps for thermal tests on luminaires for incandescent lamps 5.1 The lamp cap temperature rise shall be equal to th

32、e maximum permissible cap temperature rise (At, max.) for the specific lamp type as specified in the appropriate table of IEC 432. 5.2 The rated wattage, dimensions and caps are given in tables 1 and 2. Table 1 - Values for H.T.S. lamps for heating tests on luminaires for normal G.L.S. lamps Rated w

33、 at lag e bulb diameter and -bulb shape I 60 1 O0 150 200 60 A or PS 60 A or PS 65 to 80 A or PS 80 A or PS Maximum overall length 110 108,5 110 108.5 166.5 165 166.5 E27 B22d E27 B22d E27 B22d E27 See IEC 887 CENELEC ENtbOb34 95 W 3404583 0155785 802 D Page 6 EN 60634 : 1995 Table 2 - Values for H.

34、T.S. lamps for heating tests on luminaires for candle and round bulb lamps Rated wattage W 40 60 40 60 Nominal bulb diameter and -bulb shape mrn 35-BorC 35 - B or C 45 - G or P 45 - G or P Maximum overall length rnm 104 983 102.5 97 104 102.5 80 74 78,5 72.5 80 78.5 E14 E27 B15d B22d E14 B15d E14 E2

35、7 B15d B22d E14 B15d I See IEC 887 5.3 The tolerances on rated wattage and lamp cap temperature rise shall be within the limits defined by the area A, B, C, D, E, F in figure 1. The relevant test voltage shall be marked on the lamp or shall be specified on the data sheet delivered with the H.T.S. la

36、mps. NOTE - The test voltage and finish of the H.T.S. lamp are not specified in order to allow the manufacturer some freedom to achieve the specified cap temperature rise. CENELEC ENsbOb34 75 = 3404583 Ol15578b 747 m Page 7 EN 60634 : 1995 -2 -1 I C E D IEC ?Mi93 6W % is the percentage variation in

37、rated wattage 6Ats Ob is the percentage variation in lamp cap temperature rise NOTE - The shape of the tolerance field above takes into account the fact that in the production of H.T.S. lamps, the spread in cap temperature rise is much larger than that in wattage. Experience has shown that the influ

38、ence of the wattage tolerance on the temperature measured at the bifurcation point of the luminaire is 1.5 times greater than that of the cap temperature rise tolerance. This allows a widening of the cap temperature rise tolerance thus enabling a greater number of lamps to be selected as H.T.S. The

39、area enclosed by A, B, C, D, E and F has been chosen to allow for the tolerance spread of cap temperature rise to be greater than the spread of wattage tolerance. Figure 1 - Tolerances on wattage and lamp cap temperature rise CENELEC ENxhOh34 95 = 3404583 0355787 685 W Page 8 EN 60634 : 1995 Annex A

40、 (no r mat ive) Survey of the origin and development of heat test source lamps A.1 Introduction Luminaires for incandescent lamps must satisfy various safety requirements. Two of the most important requirements are that the user must be safeguarded against accidental contact with live parts and agai

41、nst fire hazard. This necessitates stringent limits with regard to temperatures that arise during operation (see IEC 598-1). The temperature limits applicable to the materials used in the luminaire shall not be exceeded in order to prevent premature ageing, melting or shrinking of parts providing pr

42、otection against electric contact or parts holding current-carrying parts in position. To check this, it is necessary that luminaires should be submitted to thermal tests during type testing. For such tests, two types of test lamps are generally necessary, namely: - heat test source (H.T.S.) lamps,

43、to check primarily the effect of heat conducted through the lamp cap on the lampholder and its wiring; - radiation test source (R.T.S.) lamps, in order to check the effect of radiated energy on the temperature of other parts of the luminaire. For this purpose, a commercial lamp of the relevant bulb

44、finish and shape, dimensions, cap and rated voltage should be taken. It is essential that the bulb is clean and free of extraneous markings, coating and the like. It is also necessary to give some consideration to the filament configuration for LV (100 V - 130 V) G.L.S. lamps since some designs use

45、axial, while others use trans- verse or wreath filaments, which could produce different temperature patterns in luminaires. In the case of reflectors or bowl-mirror lamps, these can also be used as R.T.S. lamps, but in a version where the non-reflector part is clear (if such a version is available c

46、ommercially). Radiation test source (R.T.S.) lamps do not need to have controlled Ats. CENELEC EN*b0634 95 3404583 0155788 511 = Page 9 EN 60634 : 1995 A.2 Basic rules for the H.T.S. system The H.T.S. and the corresponding temperature measurement of luminaires are based on the following fundamental

47、rules. 1) H.T.S. lamps are basically defined by rated wattage, dimensions, type of cap and cap temperature rise. 2) The method of measuring the lamp cap temperature rise Ats (sleeve method) speci- fied in IEC 360. 3) Maximum average cap temperature rises have been specified in IEC 432 for incan- des

48、cent production lamps of various rated wattages. 4) For such rated wattages H.T.S. lamps are intended to represent the lamps having the highest permissible average cap temperature rises for the relevant rating. 5) Luminaires shall be marked with the maximum rated wattage of the lamp(s) to be used. A

49、.3 General considerations 1) The basis of the CEE/IEC 1963 “Gentlemens agreement“ was that existing good practice for lamps should not have to be modified as a consequence of the new require- ments. This basis still holds good today. 2) The CEE/IEC 1963 agreement was laid down in detail only for pear-shaped lamps for mains supply with E27 caps in the following ratings: 60 W, 100 W, 150 W, 200 W and 300 W. Subsequently, values were derived for lamps with the ratings 60 W, 100 W and 150 W but capped with 822. 3) Lamp