EN 45510-2-4-2000 en Guide for procurement of power station equipment - Part 2-4 Electrical equipment - High power static convertors《发电站设备的采购指南 第2-4部分 电力设备 高功率静态转换器》.pdf

《EN 45510-2-4-2000 en Guide for procurement of power station equipment - Part 2-4 Electrical equipment - High power static convertors《发电站设备的采购指南 第2-4部分 电力设备 高功率静态转换器》.pdf》由会员分享，可在线阅读，更多相关《EN 45510-2-4-2000 en Guide for procurement of power station equipment - Part 2-4 Electrical equipment - High power static convertors《发电站设备的采购指南 第2-4部分 电力设备 高功率静态转换器》.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD Guide for procurement of power station equipment - Part 2-4: Electrical equipment - High power static convertors The European Standard EN 45512-4:2000 has the status of a British Standard ICs 27.100, 29.200 NO COPYING WITHOUT BSI PERMISSION EXCEPT As PERMITED BY COPYRIGHT LAW BS EN

2、455 10-242000 Imwrporating Comigendum No. 1 This British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 June 2000 Amd No. Date 11040 August 2000 Corrigendum No. 1 Q BSI 0

3、82000 Comments Error in title corrected National foreword This British Standard is the official English language version of EN 455111242000. The UK palicipation in its preparation was entrusted to Technical Committee W-/20, Power engineering steering committee, which has the responsibility to: - aid

4、 enquirers to understand the text; - present to the responsible European committee any enquiries on the - monitor related international and European developments and promulgate interpretation, or proposals for change, and keep the UK interests informed; them in the UK. A list of organizationS repres

5、ented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Intedod Standards Correspondence Ind

6、ex”, or by using the “Fnd” facility of the BSI Standards Elecironic Catalogue. A British Standard does not purport to include all the necessary provisions of a conhct Users of British standards are responsible for their correct application. Compliance with a British Standard does not of itself confe

7、r immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 29 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued ISBN O 580 34499 1 STD.BSI BS EN 45510-

8、2-q-ENGL 2000 1b24bb9 OBbb119 123 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 45510-2-4 March 2000 ICs 27.100; 29.200 English version Guide for procurement of power station equipment - Part 2-4: Electrical equipment - High power static convertors Guide pour lacquisition dquipements destins

9、aux centrales de production dlectricit - Partie 2-4: Equipements lectriques - Convertisseurs de puissance Leitfaden fr die Beschaffung von Ausrstungen fr Kratwerke - Teil 2-4: Elektrische Ausrstung - Statische Hochleistungsumnchter This European Standard was approved by CENICENELEC on 1 February 200

10、0. CENICENELEC members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving th6 European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references corcerning such national standards may be obt

11、ained on application to the Central Secretariat or to any CENICENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENICENELEC member into its own language and notified to

12、 the Central Secretariat has the same stdus as the official versions. CENICENELEC members are the national standards bodies and national electrotechnical committees, respectively, of Austria, Belgiim, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Net

13、herlands, Norway, Portugal,Spain, Sweden, Switzerland and United Kingdom. CEN Central Secretariat: rue de Stassart, 36 8-1050 Brussels CENELEC CENELEC Central Secretariat: rue de Stassart, 35 B-I 050 Brussels Q 2000 CENICENELEC All rights of exploitation in any form and by any means reserved worldwi

14、de for CEN national Members and for CENELEC Mem bers. Ref. No. EN 45510-242000 E Page 2 EN 45510-2-4:2000 Contents Foreword 5 1 2 3 3.1 3.2 3.3 4 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 5 6 7 7.1 7.2 7.3 7.4 7.5 7.6 7.7 8 8.1 8.2 Scope . 7 Normative references . 8 Definitions 8 Organizational terms 8 Te

15、chnical terms 9 General terms 9 Brief overall project description 10 Role and organization of purchaser 10 Equipment task . 10 Equipment to be purchased 10 Control and instrumentation . 11 Electrical supplies and other services 11 Other interfaces 11 Site location . 10 Project programme . 11 Equipme

16、nt identification systems . 11 Extent of supply 12 Terminal points . 13 Operational requirements . 13 Operating environment . 13 Manning levels 13 Normal operation 13 Operating hours 13 Start-up and shut-down 14 Abnormal conditions . 14 Further operational requirements . 14 Life expectancy . 14 Desi

17、gn life . 14 Components requiring periodic maintenance . 15 O BSI 08-2000 Page 3 EN 45510-2-4:2000 9 Performance requirements 15 9.1 Duty . 15 9.2 Performance 16 9.3 Equipment margins . 16 9.4 Availability . 17 9.5 9.6 IO Levels of component redundancy . 17 Further performance requirements . 17 Desi

18、gn and fabrication 17 10.1 10.2 10.3 10.4 10.5 10.6 11 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 12 12.1 12.2 13 Specific equipment features 17 Design justification 20 Material selection 20 Safety 20 Interchangeability 21 Maintenance requirements 21 Planned maintenance . 21 Personnel safety . 21 Requi

19、rements for access 21 Special tools 22 Spare parts strategy 22 Special precautions . 22 Technical documentation requirements 22 Tender documentation 22 Contract documentation 22 Applicable legislation, regulations, standards and further requirements . 23 Fabrication methods 21 Lifting requirements 2

20、1 Test equipment . 22 13.1 13.2 Standards 23 13.3 Further requirements . 23 14 Evaluation criteria 23 14.1 General . 23 14.2 Technical criteria . 24 Legislation and regulations . 23 O BSI 08-2000 Page 4 EN 45510-2-4:2000 15 15.1 15.2 15.3 15.4 16 16.1 16.2 16.3 17 17.1 17.2 17.3 17.4 17.5 Quality me

21、asures 25 General . 25 Approvals procedure 25 Inspection requirements . 25 Non-conformity . 25 Access 25 Site specific requirements 26 Verification of specified perfomance . 26 Works tests . 26 Tests during installation and commissioning 27 Technical conditions for trial run . 27 Functional and perf

22、ormance tests 28 Site factors 25 Facilities 25 General . 26 Annex A (informative) Bibliography . 29 O BSI 08-2000 Page 5 EN 45510-2-42000 Foreword This standard takes the form of a recommendation and is therefore entitled a “Guide“. This Guide for procurement has been prepared by the CEN/CENELEC Joi

23、nt Task Force Power Engineering (JTFPE) of which the Secretariat is held by the British Standards Institution. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2000, and conflicting natio

24、nal standards shall be withdrawn at the latest by September 2000. Annexes designated “informative“ are given for information only. In this standard, annex A is informa tive. This Guide for procurement has been prepared under mandates given to CEN and CENELEC by the European Commission and the Europe

25、an Free Trade Association. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembour

26、g, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. This Guide for procurement is a part of a series of Guides mandated to cover the procurement of power station plant and equipment in conformity with European Procurement Directives. The Guides are: EN 45510: Guide f

27、or procurement of power station equipment Part I: Common clauses Part 2-1: Electrical equipment - Power transformers Part 2-2: Electrical equipment - Unintermptible power supplies Part 2-3: Electrical equipment - Stationary batteries and chargers Part 2-4: Electrical equipment - High power static co

28、nvertors Part 2-5: Electrical equipment - Motors Part 2-6: Electrical equipment - Generators Part 2-7: Electrical equipment - Switchgear and controlgear Part 2-8: Electrical equipment - Power cables Part 2-9: Electrical equipment - Cabling systems Part 3-1: Boilers - Water tube boilers Part 3-2: Boi

29、lers - Shell boilers Part 3-3: Boilers - Boilers with fluidized bed firing Part 4-1: Boiler auxiliaries - Equipment for reduction of dust emissions Part 4-2: Boiler auxiliaries - Gas-air, steam-air and gas-gas heaters Part 4-3: Boiler auxiliaries - Draught plant Part 4-4: Boiler auxiliaries - Fuel p

30、reparation equipment Part 4-5: Boiler auxiliaries - Coal handling and bulk storage plant Part 4-6: Boiler auxiliaries - Flue gas desulphurization ( De-Sa) plant Part 4-7: Boiler auxiliaries - Ash handling plant Part 4-8: Boiler auxiliaries - Dust handling plant Part 4-9: Boiler auxiliaries - Sootblo

31、wers Part 4-10: Boiler auxiliaries - Flue gas denitrification (De-Na) plant O BSI 08-2000 Page 6 EN 4551 O-2-4:2000 Part 5-1: Turbines - Steam turbines Part 5-2: Turbines - Gas turbines Part 5-3: Turbines -Wind turbines Part 5-4: Turbines - Hydraulic turbines, storage pumps and pump-turbines Part 6-

32、1 : Turbine auxiliaries - Deaerators Part 6-2: Turbine auxiliaries - Feedwater heaters Part 6-3: Turbine auxiliaries - Condenser plant Part 6-4: Turbine auxiliaries - Pumps Part 6-5: Turbine auxiliaries - Dry cooling systems Part 6-6: Turbine auxiliaries - Wet and wetldry cooling towers Part 6-7: Tu

33、rbine auxiliaries - Moisture separator reheaters Part 6-8: Turbine auxiliaries - Cranes Part 6-9: Turbine auxiliaries - Cooling water systems Part 7-1 : Pipework and valves - High pressure piping systems Part 7-2: Pipework and valves - Boiler and high pressure piping valves Part 8-1 : Control and in

34、strumentation EN 4551 O Part 1 contains those clauses common to all the above Guides giving the provisions of a non equipment specific nature for use in the procurement of power station plant. EN 4551 O is the responsibility of JTFPE. The so called “common clauses“, as appropriate, also appear in it

35、alics in the documents specific to particular equipment. In this Guide, words in bold type indicate that they have the meaning given in the definitions, clause 3. In this Guide, words and sentences not in italics are specific to this Guide and refer to the particular equipment covered. O BSI 08-2000

36、 Page 7 EN 4551 0-2-4:2000 1 Scope This standard gives guidance on writing the technical specification for the procurement of static a.c. and d.c. high power convertors for use in electricity generating stations (power stations). This Guide for procurement is not applicable to equipment for use in t

37、he nuclear reactor plant area of nuclear power stations. Other possible applications of such equipment have not been considered in the preparation of this Guide. This Guide covers each type of power convertor, .e. rectifier, inverter, static excitation system, conversion of a.c. to a.c.1d.c. to d.c.

38、 and switching, for the purpose of changing andlor controlling one or more characteristics. This type of equipment is used for many applications such as motor drives and actuators, e.g. variable frequency starting equipment, a.c. and d.c. power supplies for computers and instrumentation, in chemical

39、 process plant, e.g. rectifiers for electrolysis in hydrogen production, in mechanical plant, e.g. electrostatic precipitators, etc. For additional, or specific, requirements for batteries, battery chargers or uninterruptible power supplies (UPS) refer to the relevant guides in this series. The equi

40、pment covered by this Guide is defined by its function rather than design type. Therefore, the guidance to the specification is stated in performance terms rather than being specified by a detailed description of the equipment to be supplied. This Guide indicates to potential purchasers how their sp

41、ecification should be prepared so that - - predicted performance is achieved, - - - the equipment type and capacity interfaces correctly with other elements of the systems, ancillary equipment is properly sized, reliability, availability and safety requirements are achieved, proper consideration is

42、given to the evaluation process and the qualify measures to be applied. This Guide does not determine the type ofspecification (e.g. detailed, performance, functional) or the extent of supply for any given contract which is normally decided on the basis of thepurchasers project strategy. It does not

43、 cover - - any commercial, contractual or legal issues which are normally in separate parts of an enquiry, any allocation of responsibilities which are determined by the contract. This Guide does not prescribe the arrangement of the documents in the enquiry. NOTE: As a comprehensive European environ

44、mental policy is still under preparation, this Guide does not address the environmental implications of the equipment. O BSI 08-2000 Page 8 EN 45510-2-4:2000 2 Normative references This Guide for Procurement incorporates by dated or undated reference, provisions from other publications. These normat

45、ive references are cited in the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this Guide only when incorporated in it by amendment or revision. For undated references, the la

46、test edition of the publication referred to applies. European Standards EN IS0 9001 Quality systems - Model for quality assurance in design, development, production, installation and servicing EN IS0 9002 Quality systems - Model for quality assurance in production, installation and servicing EN 5009

47、1 Specification for uninterruptible power systems (UPS) Part 1 : General and safety requirements Part 2: EMC requirements EN 60146 series Semiconductor convertors - General requirements and line commutated convertors Patt 1-1: Specification of basic requirements (IEC 60146-1-1) Patt 1-3: Transformer

48、s and reactors (IEC 60146-1-3) EN 60529 Degrees of protection provided by enclosures (IP Code) (IEC 60529) International Standards IEC 60050-191 International electrotechnical vocabulary Chapter 191: Dependability and Quality of Services IEC 60050-551 International electrotechnical vocabulary Chapte

49、r 551: Power electronics IEC 60146 series Semiconductor convertors - General requirements and line commutated convertors Part 1-2: Application guide Part 3: Semiconductor d.c. convertors (d.c. chopper convertors) 3 Definitions for the purposes of this Guide, the following definitions apply, 3.1 Organizational terms 3. I. I purchaser: Recipient of a product andor a service provided by a supplier. 3.1.2 supplier Person or organization that provides a product andor a service to the purchaser. 3.1.3 specification: Document stating technical requirements of the purchaser It may