EN 14513-2005 en Transportable gas cylinders - Bursting disc pressure relief devices (excluding acetylene gas cylinders)《可移动出储气瓶 防爆板压力释放装置(不含乙炔储气瓶)》.pdf

《EN 14513-2005 en Transportable gas cylinders - Bursting disc pressure relief devices (excluding acetylene gas cylinders)《可移动出储气瓶 防爆板压力释放装置(不含乙炔储气瓶)》.pdf》由会员分享，可在线阅读，更多相关《EN 14513-2005 en Transportable gas cylinders - Bursting disc pressure relief devices (excluding acetylene gas cylinders)《可移动出储气瓶 防爆板压力释放装置(不含乙炔储气瓶)》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 14513:2005Transportable gas cylinders Bursting disc pressure relief devices (excluding acetylene gas cylinders)The European Standard EN 14513:2005 has the status of a British StandardICS 23.020.30g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g5

2、4g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 14513:2005This British Standard was published under the authority of the Standards Policy and Strategy Committee on 24 November 2005 BSI 24 November 2005ISBN 0 580 47312 0Natio

3、nal forewordThis British Standard is the official English language version of EN 14513:2005.The UK participation in its preparation was entrusted by Technical Committee PVE/3, Gas containers, to Subcommittee PVE/3/1, Valve fittings for gas containers, which has the responsibility to:A list of organi

4、zations represented on this subcommittee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Corresp

5、ondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not of i

6、tself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and pr

7、omulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date Comm

8、entsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 14513March 2005ICS 23.020.30English versionTransportable gas cylinders - Bursting disc pressure reliefdevices (excluding acetylene gas cylinders)Bouteilles gaz - Bouteilles gaz transportables -Dispositifs limiteurs de pression disque de rupture (

9、lexclusion des bouteilles pour actylne)Ortsbewegliche Gasflaschen - Berstscheibeneinrichtungenzur Druckentlastung (ausgenommen fr Acetylenflaschen)This European Standard was approved by CEN on 14 February 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate

10、the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in

11、three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Au

12、stria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZ

13、ATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14513:2005: EEN 14513:2005 (E) 2 Contents Page Foreword3 1 S

14、cope 4 2 Normative references 4 3 Terms and definitions .4 4 Requirements.5 5 Bursting disc pressure relief device assembly 7 6 Production testing .7 7 Cleanliness .8 8 Marking and packaging.8 Bibliography 9 EN 14513:2005 (E) 3 Foreword This document (EN 14513:2005) has been prepared by Technical Co

15、mmittee CEN/TC 23 “Transportable gas cylinders”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2005, and conflicting national standards shall b

16、e withdrawn at the latest by September 2005. This document includes a Bibliography. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Est

17、onia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 14513:2005 (E) 4 1 Scope This document specifies the requirements for the desig

18、n, manufacture and testing for bursting disc pressure relief devices for use with gas cylinders. It is a requirement of this document that the bursting disc pressure relief devices conform to EN ISO 4126-2. In the event of a conflict, the requirements of this document take precedence over that stand

19、ard. This document does not apply to acetylene gas cylinders and is restricted to bursting disc pressure relief devices for gas cylinders used in some specific applications. NOTE This document does not provide methods for determining the capacity of a bursting disc pressure relief device for a parti

20、cular gas cylinder. This document will not indicate when a bursting disc pressure relief device shall be fitted and at which pressure it will be set, see EN 13096. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references,

21、only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 4126-2:2003, Safety devices for the protection against excessive pressure Part 2: Bursting disc safety devices (ISO 4126-2:2003). EN ISO 11114-1, Transport

22、able gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials (ISO 11114-1:1997). EN ISO 11114-2, Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials (ISO 11114-2:2000). EN ISO 1111

23、4-3, Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 3: Autogenous ignition test in oxygen atmosphere (ISO 11114-3:1997). ISO 10156, Gases and gas mixtures Determination of fire potential and oxidizing ability for the selection of cylinder valve outle

24、ts. 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 4126-2:2003 and the following apply. 3.1 pressure pressure relative to atmospheric pressure, i.e. gauge pressure 3.2 specified minimum temperature lowest temperature for which the bursting disc p

25、ressure relief device is specified 3.3 specified maximum temperature highest temperature for which the bursting disc pressure relief device is specified 3.4 coincident temperature temperature of the bursting disc pressure relief device associated with a bursting pressure and which is the expected te

26、mperature of the bursting disc when it is required to burst (i.e. the set pressure) EN 14513:2005 (E) 5 3.5 bursting disc pressure relief device with non replaceable rupture disc rupture disc assembly whose rupture disc is permanently joined to the holder by the manufacturer. The rupture disc is des

27、igned to burst at a predetermined pressure to permit the discharge of the gas 3.6 rated burst pressure maximum pressure at which the disc is designed to rupture at one specific temperature range 4 Requirements 4.1 General The bursting disc pressure relief device shall satisfy all the requirements of

28、 EN ISO 4126-2 except where this document takes precedence. The bursting disc pressure relief device assembly is normally fitted to the cylinder valve (see Figure 1). The assembly and its components shall not be capable of being overstressed in normal operation. The design of holder assemblies shall

29、 ensure that any failure due to overstressing during fitting does not result in ejection of material or contents. EN 14513:2005 (E) 6 Key 1 Burst disc cup 2 Sealing ring 3 Screw 4 Pressure direction 5 Burst disc housing 6 Indicator plug for burst disc Figure 1 Bursting disc 4.2 Design 4.2.1 Design t

30、emperature The specified minimum temperature shall be equal to 40 C, unless otherwise specified. The specified maximum temperature shall be + 65 C, unless a higher temperature is specified. 4.2.2 Coincident temperature The coincident temperature used as a reference shall be + 15 C unless otherwise s

31、pecified by the purchase order. EN 14513:2005 (E) 7 4.2.3 Creation of solids on reduction of pressure Where the bursting disc pressure relief device is specified as suitable for service with products that change from gas, liquid or vapour to solid, e.g. CO2, the design shall be such as to avoid redu

32、ction of the discharge area below that required due to accumulation of the solid product. 4.2.4 Eflux ports from bursting discs The gas discharge following rupture of a bursting disc should be directed such that the gas cylinder is not made unstable such that it could fall over. 4.3 Materials 4.3.1

33、Metallic materials Metallic materials shall be in conformance with EN ISO 11114-1 as appropriate to the gas to be relieved. The strength of the materials shall be adequate for their duty at the maximum specified temperature and the elongation of the materials at the minimum specified material proper

34、ties. 4.3.2 Non- metallic materials Non-metallic materials shall be in conformance with reference EN ISO 11114-2 and/or EN ISO 11114-3 as appropriate to the gas to be relieved. 4.3.3 Corrosion resistance Bursting disc materials shall be resistant to normal atmospheric corrosive agents. Thus particul

35、ar care shall be taken to ensure that the selected materials of the bursting disc, together with any coating are appropriate such that premature failure or any other malfunction cannot occur. Some copper alloys are susceptible to stress corrosion cracking, consequently careful consideration shall be

36、 given to the assembly before selection of these materials for components under stress and exposed to the corrosive media. 4.3.4 Oxygen compatibility For oxidizing gases as defined by ISO 10156, the materials shall be oxygen compatible in accordance with EN ISO 11114-1 and EN ISO 11114-3. 5 Bursting

37、 disc pressure relief device assembly It shall be ensured that only a single bursting disc is fitted to each bursting pressure relief device assembly. 6 Production testing The pressure and burst tests shall be performed in accordance with the requirements of EN ISO 4126-2. Bursting discs with a corr

38、osion resisting coating shall have the integrity of the corrosion resistant coating demonstrated prior to pressure testing. The test medium for hydraulic tests shall be “clean water“ or “air“ and for pneumatic tests oil free air or an inert gas such as nitrogen. Before performing the pressure and bu

39、rst tests, the manufacturers specifications relating to assembly/torques/ procedures shall be followed. EN 14513:2005 (E) 8 7 Cleanliness All parts shall be cleaned for the intended service, EN 12300 may be used as a guide. 8 Marking and packaging The bursting disk or its holder shall have tamper ev

40、ident seals and shall be marked with: the number of this document; the burst pressure. In addition on the packaging, e.g. for the delivery of the disk, shall be : manufacturer; model; size; material; batch identity. EN 14513:2005 (E) 9 Bibliography 1 EN 12300:1998, Cryogenic vessels Cleanliness for

41、cryogenic service. 2 EN 13096, Transportable gas cylinders Conditions for filling gases into receptacles Single component gases. BS EN 14513:2005BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It

42、presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of B

43、SI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20

44、8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer

45、 Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Stan

46、dards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on a

47、ll its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and

48、other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at ht

49、tp:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.Th