EN 635-5-1999 en Plywood - Classification by Surface Appearance - Part 5 Methods for Measuring and Expressing Characteristics and Defects《胶合板 按表观分类 第5部分 特征及缺陷的测量和表述方法》.pdf

《EN 635-5-1999 en Plywood - Classification by Surface Appearance - Part 5 Methods for Measuring and Expressing Characteristics and Defects《胶合板 按表观分类 第5部分 特征及缺陷的测量和表述方法》.pdf》由会员分享，可在线阅读，更多相关《EN 635-5-1999 en Plywood - Classification by Surface Appearance - Part 5 Methods for Measuring and Expressing Characteristics and Defects《胶合板 按表观分类 第5部分 特征及缺陷的测量和表述方法》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 STD-BSI BS EN b35-5-ENGL 1777 Lb2Ybb9 0797085 753 W BRITISH STANDARD Plywood - Classification by surface appearance - Part 5: Methods for measuring and expressing characteristics and defects The European Standard EN 63561999 has the status of a British Standard ICs 79.060.10 BS EN i35-5:1999 - U NO

2、 COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGm LAW STD.BS1 BS EN b35-5-ENGL 1999 Lb21ibb7 079708b b7T 9 direction of the Sector Committee for Buiidmg and Civil Engineering, was published under the authority of the Standards Committee and comes into effect on 15 August 1999 Amd. No.

3、O BSI 08-1999 BS EN 635-5:1999 Date Comments National foreword This British Standard is the English language version of EN 6355: 1999. The UK participation in its preparation was entrusted to Technical Committee B41, Wood-based panels, which has the responsibility to: - aid enquirers to understand t

4、he text; - present to the responsible European committee any enquiries on the - monitor related international and European developments and promulgate interpretation, or proposals for change, and keep the UK interests hformed them in the UK A list of organizations represented on this committee can b

5、e obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “F

6、ind” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contsact. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from leg

7、al obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright notice displayed throughout this document indicates when the document was last issued. ISBN O 580 32361 7 STD-BSI B

8、S EN b35-5-ENGL 1999 II Lb2LibbS 0797087 52b m EUROPEAN sr.ANDm EN 635-5 NOFWF, EUROPENNE EUROP and - a tramparent or semi-tramparent film printed with a rectangular grid; or - any optical system, able to measure the requested quantities, i.e. lengths, wid*, diameters and areas. 6 Methods for measur

9、ement 6.1 Quantity in number Quantities in number of characteristics and defects shall be related to the full panel surface area anel length multiplied by panel width) with the only exceptions of open splits and open joints, for which the number shail be related to the panel width. 6.2 Diameter 6.2.

10、1 The measurement shall be expressed to the nearest millimebe. 6.2.2 The diameter of knots and knot holes shall be measured as the distance between two opposite tangents plotted to the circumference of the knot (or hole) in a direction parallel to the wood fibre direction of the surface veneer (see

11、Figure 1). a) Length direction of the panel Figure 1- Dimensions to be used to express the diameter (d) of knot holes and similar characteristics 6.3 Length 6.3.1 The measurement shall be expressed to the nearest millime or 6.6.2.2 scanning the tracing with suitable electronic 6.6.3 Direct measureme

12、nt The area of the characteristic or defect can be measured directly using a suitable electsonic image identification equipment. Annex A (informative) Bibliography ENV 635-4, Plywood - Classifkatwn by Ju.sclce appearance - Part 4: Parameters of ability for finishing - GuuEeline. Figure 4- “kacing of

13、 the outline of a characteristic or a defect on a transparent squared grid used to determine the area 7 Test report The test report b) their number, length, width or area as wProP*, c) the method used for determination of the area 6.6.2.1,6.6.2.2 or 6.6.3. O BSI 08-1999 BS EN 635-51999 BSI 389 Chisw

14、ick High Road London w4 4AL STDaBSI BS EN b35-5-ENGL 1979 8 1bZqbb7 0797093 821 _ - BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards. It ?resents the UK view on standards in Europe and at the internaional level. It is ncorporated by

15、 Royai Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. t is the constant aim of BSI to improve the quaJity of our products and services. We would be grateful if anyone finding

16、an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel 020 8996 9ooo. Fax: 020 996 7400. BSI offers members an individual updating service called PLUS which ensu

17、res that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is

18、 BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of informion on national, European and international standards through its Library and its Technical Help to Exporters S

19、ervice. Various BSI electronic information services are also available which give details on all its products and services. Contact the information Centre. Tel: 020 8996 71 11. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial disc

20、ounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel 020 8996 7002. Fax: O20 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standard

21、ization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not pr

22、eclude the free use, in the course of implementing the standard, of necessary details such as symbois, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior wrien permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel 020 8996 7070.