EN 474-9-2006 en Earth-moving machinery - Safety - Part 9 Requirements for pipelayers (Incorporates Amendment A1 2009)《土方机械 安全准则 第9部分 铺管机的要求 包含修改件A1-2009》.pdf

《EN 474-9-2006 en Earth-moving machinery - Safety - Part 9 Requirements for pipelayers (Incorporates Amendment A1 2009)《土方机械 安全准则 第9部分 铺管机的要求 包含修改件A1-2009》.pdf》由会员分享，可在线阅读，更多相关《EN 474-9-2006 en Earth-moving machinery - Safety - Part 9 Requirements for pipelayers (Incorporates Amendment A1 2009)《土方机械 安全准则 第9部分 铺管机的要求 包含修改件A1-2009》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 474-9:2006+A1:2009 Earth-moving machinery Safety Part 9: Requirements for pipelayersICS 53.100g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g

2、43g55g3g47g36g58BS EN 474-9:2006+A1:2009This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2007 BSI 2009ISBN 978 0 580 62373 8National forewordThis British Standard is the UK implementation of EN 474-9:2006+A1:2009. It supersedes BS

3、EN 474-9:2006, which is withdrawn.The UK participation in its preparation was entrusted by Technical Committee B/513, Construction equipment and plant and site safety, to Subcommittee B/513/1, Earth moving machinery (International).A list of organizations represented orequest to its secretary.n this

4、 subcommittee can be obtained on This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication

5、Date CommentsImplementation of CEN amendment A1:2009The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by .A1A131 May 2

6、009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 474-9:2006+A1 February 2009 ICS 53.100 Supersedes EN 474-9:2006English Version Earth-moving machinery - Safety - Part 9: Requirements for pipelayers Engins de terassement - Scurit - Partie 9: Prescriptions applicables aux poseurs de canalisatio

7、ns Erdbaumaschinen - Sicherheit - Teil 9: Anforderungen fr Rohrverleger This European Standard was approved by CEN on 17 April 2006 and includes Amendment 1 approved by CEN on 20 December 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions f

8、or giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three offic

9、ial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria,

10、 Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTE

11、E FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 474-9:2006+A1:2009: EEN 474-9:2006+A1:200

12、9 (E) 2 Contents Page Foreword 3Introduction .51 Scope 62 Normative references 63 Terms and definitions .74 List of additional significant hazards 75 Safety requirements and/or measures 75.1 General 75.2 Operators station 85.3 Stability and lifting equipment .85.4 Rear mounted winch .95.5 Noise .96

13、Information for use . 106.1 Warning signs . 106.2 Operation manual . 106.3 Machine marking. 10Annex A (normative) List of additional significant hazards Pipelayers . 11Annex B (informative) Illustrations . 12Annex ZA (informative) Relationship between this European Standard and the Essential Require

14、ments of EU Directive 98/37/EC . 14Annex ZB (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“ 15Bibliography . 16Figures Figure B.1 Crawler pipelayer 12 Figure B.2 Wheel pipelayer 12 Figure B.3 Pipelayer side view . 13 Figure B.4 Cr

15、awler pipelayer with a rotating upper structure 13 Tables Table A.1 List of additional significant hazards . 11 EN 474-9:2006+A1:2009 (E) 3 Foreword This document (EN 474-9:2006+A1:2009) has been prepared by Technical Committee CEN/TC 151 “Construction equipment and building material machines Safety

16、”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. This

17、document includes Amendment 1, approved by CEN on 2008-12-20. This document supersedes !EN 474-9:2006“. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. This document has been prepared under a mandate given to CEN by the European Commission and th

18、e European Free Trade Association, and supports essential requirements of EU Directive. !For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this document.“ For bibliographic references, see !EN 474-1:2006+A1:2009“. EN 474 “Earth-moving machinery Saf

19、ety“ comprises the following parts: Part 1: General requirements Part 2: Requirements for tractor-dozers Part 3: Requirements for loaders Part 4: Requirements for backhoe-loaders Part 5: Requirements for hydraulic excavators Part 6: Requirements for dumpers Part 7: Requirements for scrapers Part 8:

20、Requirements for graders Part 9: Requirements for pipelayers Part 10: Requirements for trenchers Part 11: Requirements for earth and landfill compactors Part 12: Requirements for cable excavators This European Standard is intended for use in combination with Part 1 of the series. According to the CE

21、N/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, EN 474-9:20

22、06+A1:2009 (E) 4 Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 474-9:2006+A1:2009 (E) 5 Introduction This part of EN 474 is a type C standard as stated in EN ISO 12100-1:2003. The machinery concerne

23、d and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this European Standard. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over

24、 the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard. EN 474-9:2006+A1:2009 (E) 6 1 Scope This part of EN 474 deals with all significant hazards, hazardous situations and events relevant to pipelayers as defined in

25、 EN ISO 6165:2006, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). The requirements of this part are complementary to the common requirements formulated in !EN 474-1:2006+A1:2009“. This part does not repeat the requir

26、ements from !EN 474-1:2006+A1:2009“, but adds or replaces the requirements for application for pipelayers. This part specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, hazardous situations and events during commissioning, operation and mai

27、ntenance of pipelayers. This part specifies additional requirements for rear mounted winches. Pipelayers with rotating upper structure are excluded from the scope of this document. However, specific requirements are under development. This European Standard is not applicable to pipelayers manufactur

28、ed before the date of publication of this European Standard by CEN. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the refer

29、enced document (including any amendments) applies. !EN 474-1:2006+A1:2009“, Earth-moving machinery Safety Part 1: General requirements EN 1032:2003, Mechanical vibration Testing of mobile machinery in order to determine the vibration emission value EN 1677-1:2000, Components for slings Safety Part 1

30、: Forged steel components, Grade 8 EN 1677-2:2000, Components for slings Safety Part 2: Forged steel lifting hooks with latch, Grade 8 !EN ISO 3411:2007, Earth-moving machinery - Physical dimensions of operators and minimum operator space envelope (ISO 3411:2007)“ !EN ISO 7096:2008“, Earth-moving ma

31、chinery Laboratory evaluation of operator seat vibration (ISO 7096:2000) EN ISO 12100-1:2003, Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology (ISO 12100-1:2003) ISO 4308-1:2003, Cranes and lifting appliances Selection of wire ropes Part 1: Gen

32、eral !ISO 6393:2008, Earth-moving machinery - Determination of sound power level - Stationary test conditions“ !ISO 6394:2008“, Earth-moving machinery Determination of emission sound pressure level at operators position Stationary test conditions ISO 6405-2:1993, Earth-moving machinery Symbols for o

33、perator controls and other displays Part 2: Specific symbols for machines, equipment and accessories EN 474-9:2006+A1:2009 (E) 7 ISO 8813:1992, Earth-moving machinery Lift capacity of pipelayers and wheeled tractors or loaders equipped with side boom !ISO 10968:2004“, Earth-moving machinery Operator

34、s controls 3 Terms and definitions For the purposes of this European Standard, the terms and definitions given in !EN 474-1:2006+A1:2009“, EN ISO 12100-1:2003 and the following apply. NOTE 1 Terminology for pipelayers is specified in ISO 7136:2006 and illustrated in Annex B of this European Standard

35、. NOTE 2 Definitions used in EN and ISO standards referred to in this European Standard are also valid for this document. 3.1 pipelayer self-propelled crawler or wheeled machine, having pipe-laying equipment with main frame, a load-hoist mechanism, vertically pivotable side boom, and counterweight,

36、primarily designed to handle and lay pipes (see EN ISO 6165:2006) 4 List of additional significant hazards See Annex A. NOTE Annex A (normative) contains all the significant hazards, hazardous situations and events, as far as they are dealt with in this European Standard, identified by risk assessme

37、nt as significant for this type of machinery and which require action to eliminate or reduce the risk. 5 Safety requirements and/or measures 5.1 General Pipelayers shall comply with the requirements of !EN 474-1:2006+A1:2009“, as far as not modified or replaced by the requirements of this part. EN 4

38、74-9:2006+A1:2009 (E) 8 5.2 Operators station 5.2.1 Cab !EN 474-1:2006+A1:2009“, 5.3.1 applies with the exception that pipelayers do not need to be equipped with a cab. Pipelayers shall be designed and built so that an operators cab can be fitted. The manufacturer shall be able to provide the cab on

39、 demand. 5.2.2 Window(s) !EN 474-1:2006+A1:2009“, 5.3.2.7 and 5.3.2.9 apply with the addition that pipelayers equipped with a cab shall be provided with motorised wiper(s) and washer in the lifting direction. 5.2.3 Heating and ventilation !EN 474-1:2006+A1:2009“, 5.3.2.6 applies if a cab is fitted.

40、5.2.4 Operators seat Pipelayers with measured RMS-values on Z-axis, in accordance with EN 1032:2003, higher than 0,5 m/s2shall be equipped with a suspended seat complying with !EN ISO 7096:2008“ class EM6. As an alternative without testing the machine, the pipelayers shall be equipped with a suspend

41、ed seat complying with !EN ISO 7096:2008“ class EM6. 5.2.5 Operators protection !EN 474-1:2006+A1:2009“, 5.3.3 does not applied for pipelayers. 5.3 Stability and lifting equipment 5.3.1 General !EN 474-1:2006+A1:2009“, 5.11 applies with the additions given in 5.3.2: 5.3.2 Lifting equipment 5.3.2.1 G

42、eneral Lifting equipment shall meet the requirements in ISO 8813:1992. 5.3.2.2 Load lowering speed A device to control the lowering speed of the boom and the hook shall be fitted so that under normal working conditions the operator can control movement and stop the load. This device shall not preven

43、t the deliberate release of the free fall of the load hook (hook winch only). 5.3.2.3 Pipe laying brakes The pipe laying system shall be fitted with brakes which can be released by controls and automatically applied when the operator stops actuating or when the power source fails. The brakes shall b

44、e designed to withstand 1,5 times the rated lift capacity under conditions specified by the manufacturer. EN 474-9:2006+A1:2009 (E) 9 5.3.2.4 Hooks Hooks shall withstand a test load of 2 times the working load limit (WLL) without permanent deformation and a breaking force (BF) of 4 times the WLL acc

45、ording to EN 1677-1:2000. Hooks also used for applications other than pipelaying (e.g. transport or holding of special tooling equipment) shall have a safety latch according to EN 1677-2:2000. 5.3.2.5 Ropes Ropes shall be selected according to ISO 4308-1:2003. 5.4 Rear mounted winch 5.4.1 General NO

46、TE If a pipe-layer is equipped with a rear mounted winch, ISO 19472:2006 should be used as guidance for design. 5.4.2 Mounting The means for securing a winch to the machine structure shall be designed to withstand a force of twice the maximum line-pull that can be exerted by the rope, without perman

47、ent deformation. 5.4.3 Controls The winch controls shall be located at the operators station and shall fulfil the requirements in ISO 10968:2004. 5.4.4 Protection Provision shall be made to allow fitting for protection, when a rear mounted winch is fitted. Machines equipped with rear winch shall be

48、equipped with adequately sized protective screens (minimum 6 mm woven wire mesh with an opening of 45 mm 45 mm) or equivalent protection between the operator and the winch. The screen width and height shall be covering at least the rear of the minimum space envelope as specified in !EN ISO 3411:2007

49、“ (see Figure 5). 5.5 Noise 5.5.1 Sound power level !EN 474-1:2006+A1:2009“, 5.13.2.1 applies as follows: The sound power level for pipelayers shall be measured according to !ISO 6393:2008“. 5.5.2 Emission sound pressure level at operators station !EN 474-1:2006+A1:2009“, 5.13.2.2 applies as follows: The emission sound pressure level at operators station for pipelayers shall be measured according to !ISO 6394:2008“. EN 474-